Decibel Eleven Hot Stone Deluxe User manual
Introduction
The Hot Stone Deluxe pedal power supply was specifically designed to meet the higher power
requirements of modern digital effect pedals while providing sufficient outputs to power any
battery operated pedal. All outputs are completely isolated, filtered and regulated to provide
clean, ripple free D voltage. Isolation and short circuit protection on each output ensures that
there will be no hum, noise, or pedal interaction.
The Hot Stone Deluxe provides:
Eight isolated outputs with a total, ripple-free current of 1600mA.
Two high current, 400mA, 9 and/or 12V outputs capable of powering Eventide™ Factor,
Strymon™, Boss™ Twin, T ™ Nova, Line6™ modelers.
Two medium current, 9 or 12V outputs capable of 200mA each.
Two variable voltage outputs for simulating used carbon batteries.
ustom magnetically shielded toroidal transformer
Short circuit protection on all outlets
Box Contents
Hot Stone Deluxe
A power cord
(8) D cables with 5.5x2.1mm black barrel connectors
(2) D cables with 5.5x2.5mm blue barrel connector
(1) D cable with 3.5mm mini plug
Manual and Warranty
Declaration of Conformity
Decibel Eleven declares that this product complies with the European Union ouncil Directives and Standards
requirements for the Low Voltage Directive (2006/95/E ) and the EM Directive (2004/108/E ).
The European Union’s (EU) WEEE (Waste Electrical and Electronic Equipment) directive is for waste management of
electronic equipment sold into EU countries.The symbol on our product (shown) indicates that this product must not
be disposed of with other waste. It is the user’s responsibility to dispose of their waste electrical and electronic
equipment by handing it over to an approved reprocessor or recycler. For more information on proper recycling,
please contact your local city office or Decibel Eleven distributor.
DECIBEL11.COM
DB-11 HOT STO E OPERATI G TEMPERATURE
The Hot Stone is a linear power supply designed for low noise and high
output current. Higher currents require higher heat dissipation. The Hot
Stone is designed to radiate heat. This is normal to its operation. However,
care should be taken to keep the top cover clear and freely exposed to air.
Overview
Front Panel:
1 Power indicator LED is lighted when Hot Stone is powered on.
2 5.5mm x 2.1mm D output jacks
3 Adjustment controls for varying voltage of outputs 7 & 8.
Rear Panel:
4 Output Voltage Select Switches for outputs 5 & 6
5 A Inlet - standard IE connector.
6 A Input Voltage Switch – set to proper voltage prior to plugging in the Hot Stone
FUSE REPLACEME T
The Hot Stone Deluxe has a replaceable cartridge type fuse. Should your Hot Stone
Deluxe stop working, where there is no power being supplied to your pedals and
the green power indicator on the Hot Stone front panel is not lit, it is recommended
to check the condition of the fuse.
To access the fuse, first be absolutely certain that the unit is detached from
its A power cable. Then, remove the 2 flat head screws along the bases of the
front and rear panels. arefully remove the bottom cover from the unit. The fuse
is located at the A power cable inlet connector. Please be sure to replace the fuse
with the same type and rating: 5x20mm, 250V/500mA SLO BLO
12
3
456
Output Configuration
The Hot Stone Deluxe has 8 isolated outputs. All outputs are standard barrel type connectors
wired “center negative”, which means the outside barrel is +V. This is the standard wiring for
most guitar effect pedals. However, there are exceptions. Always check the label on the pedal
before connecting, and use a polarity reversal cable if needed (see D ables section).
Outputs 1 and 2 are each configured with separate outlets for 9V and 12V. The 9 & 12V outlets
are both fed from the same transformer winding and can supply a combined maximum output
current of 400mA. They can be used individually or simultaneously as long as the combined
current draw does not exceed 400mA.
Outputs 3 and 4 each provide up to 100mA of current at 9V. These outputs will run just about
any battery operated 9V pedal.
Outputs 5 and 6 each provide up to 200mA of current at either 9V or 12V. Use the switches
SW1 and SW2 on the rear panel to select the desired voltages.
Outputs 7 and 8 each provide up to 100mA. The output voltage for each is variable using the
control knob below the respective outlet 3 . Voltage is adjustable from 9V (fully clockwise) down
to about 5V (fully counter-clockwise). This can be used to simulate a used carbon battery, giving
transistor fuzz pedals a unique “brown” sound. The effect is not typically useful on effects which
utilize opamps in the circuitry. The voltage control is not intended to be a calibrated control. The
typical response when rotating the knob counter-clockwise will begin as a very gradual voltage
drop, increasing near the end.
DC Cables
There are three types of D cables included with the Hot Stone Deluxe:
1) 5.5x2.1mm (BLA K) to 5.5x2.1mm (BLA K): This is the standard cable used by most
pedals (BOSS™, Ibanez™, DOD™, and most 9V pedals).
2) 5.5x2.1mm (BLA K) to 5.5x2.5mm center-positive (BLUE): This cable should be used
with the Line6™ 4button modeling pedals and Eventide™ Factor pedals. These can also be
used for powering some A powered effects (depending on current draw).
3) 5.5x2.1mm (BLA K) to 3.5mm mini plug (tip positive): Use this to supply tip-positive
voltage to any pedals using 3.5mm mini jacks.
Other types power cables can be purchased including:
Polarity reversal for pedals requiring 5.5x2.1mm “center-positive” connection.
Voltage Doubling cable for combining two outputs to create 18V or 24V
urrent Doubling cable for combining two outputs to create double current.
Various lengths and end types are available for purchase.
12 3 4 5 6 7 8
4
SW2 SW1
Pedal Specifics
BOSS™ pedals are generally powered by one of two types of voltage, identified on the label as
“PSA” or “A A”. Most all BOSS™ pedals are “PSA” type and require standard 9VD . “A A” pedals
will operate correctly using any 12VD output on the Hot Stone. BOSS™ Twin pedals require
higher current and can be operated from output 5 or 6 at 9V, or output 1 or 2 at 9V.
Line 6™ Modeling pedals (4 button type) can be operated from output 5 or 6 set to 12V, or
output 1 or 2 at 12V. The BLUE 5.5x2.5mm cable must be used for these pedals.
T Electronic™ Nova pedals can be powered using the standard BLA K cable from output 5 or
6 set to 12V, or output 1 or 2 at 12V. Some pedals such as the NDR-1 Nova Drive require higher
current and must be operated from output 1 or 2 at 12V, or by using a current doubling cable
with outputs 5 & 6.
Eventide™ “Factor” pedals can be powered from output 1 or 2 at 12V using the BLUE
5.5x2.5mm cable. It is also possible to power them using a current doubling cable from outputs
5 and 6 set to 12V.
Strymon™ pedals can be powered from output 1 or 2 at 9V using the standard BLA K cable.
Other pedals will list power requirements in their manual or on the pedal itself. Some
manufacturers list actual power requirements, while others may list only the rating of the
included or recommended adapter. Often a pedal will use much less power than the
recommended adapter rating. If you are unsure of your pedals requirements, please check our
Specifications
OUTPUTS:
All outlets: 5.5x2.1mm barrel connectors, center negative.
All outlets: regulated and filtered D voltage, short circuit protected.
Outlet 1-2: 9V and/or 12V, 400mA
Outlet 3-4: 9V and/or12V, 400mA
Outlet 5-6: 9V, 100mA each
Outlet 7-8: 9V or 12V, 200mA each
Outlet 9-10: 5V-9V (continuously variable), 100mA each
INPUT:
115V/230V, 50/60Hz switchable
PHYSI AL:
Dimensions (WxDxH): 6.10" x 3.46" x 1.73"
Weight: 2.65 lbs.
DECIBEL11.COM
Table of contents
Other Decibel Eleven Music Pedal manuals
