DecorQuip DREAM 191782 User manual

DREAM CURTAIN
BATTERY MOTOR
191782
Third party port
/Smart Home Integration
LED Indicator
Setting Button
DISPLAY SCREEN
UP
STOP
DOWN
CHANNEL SELECTOR P2 SETTING BUTTONS
BATTERY
Channel selector - UP
UP
STOP
DOWN
Channel selector - DOWN
P2 Setting button
Battery
Display screen
Channel ‘0’ button
DREAM WALL SWITCH FUNCTION BUTTONS
DREAM REMOTE FUNCTION BUTTONS
MOTOR SPECIFICATION
CONTROL TYPE RADIO RATED VOLTAGE DC 14.8 V
LIMITS ELECTRONIC (set remotely) IP RATING IP40 RATED POWER 16 W
OUTPUT SPEED 20 cm/s RATED CURRENT 1.0 A MAX. LOAD 50 Kg
RATED TORQUE 1.2 N.m RADIO FREQUENCY 433.92 MHz MOTOR LENGTH 421 mm
315mm106mm
421mm
40mm
40mm
DETACHABLE
BATTERY
DREAM CURTAIN MOTOR FUNCTION BUTTONS
USB-C

SWITCHING DIRECTION METHOD 1
SWITCHING DIRECTION METHOD 2
LED
�ashes x5
beeps x3
DIRECTION
SWITCHED
Press simultaneously
for 2sec
LED
�ashes x3 Motor
beeps x3
LED
�ashes x5
beeps x3
Release
P1
Press for 2sec
within 10s
DIRECTION
SWITCHED
Press P1
for 10sec
Note:
Switching direction with a remote device is only possible before
setting top and bottom limits. To switch after limits have been set,
use METHOD 2.
PROGRAMMING INSTRUCTIONS
Before starting the process of pairing a handheld remote/wall switch to a Dream motor, choose the channel to which it is to be
paired. Channel Zero is reserved for simultaneously controlling all blinds paired to a remote and cannot be used for pairing,
programming or other adjustments. If using a battery powered motor, ensure that it is su ciently charged to complete the
set-up process.
PARING A REMOTE WITH A MOTOR
LED
�ashes x1 Motor
beeps x1
LED
�ashes x5
beeps x3
Release
P1
Press for 2sec
within 10s
PAIRING
COMPLETE
Press P1
for 2sec

SETTING LIMITS
CLEARING LIMITS
LED
�ashes x5
beeps x3
LIMITS
SET
Press for
15sec
Open curtains
to desired position Close curtains to desired position
Press for
15sec
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1
LIMITS
CLEARED
Press for
15sec
Press P2
for 15sec Press P2 for 15sec
SETTING A FAVOURITE STOP POSITION
CLEARING A FAVOURITE STOP POSITION
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1 FAVOURITE
POSITION
SET
Press for
15sec Press for 15sec
Press P2
for 15sec
Run curtains to
favourite stop position
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1 FAVOURITE
POSITION
CLEARED
Press for
15sec Press for 15sec
Press P2
for 15sec
Note:
Press the stop button
for 2 seconds to
automatically run
the curtains to a favourite
stop position.

FINE-TUNING AN OPEN LIMIT
FINE-TUNING A CLOSED LIMIT
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
Fine-tuning
mode entered
OR
OPEN
LIMIT
REFINED
Press for 5sec
simultaneously Press for 2sec simultaneously
Jog to desired
position
Adjust
manually
Run curtains to
‘open limit’
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
Fine-tuning
mode entered
OR
CLOSED
LIMIT
REFINED
Press for 5sec
simultaneously Press for 2sec simultaneously
Jog to desired
position
Adjust
manually
Run curtains to
‘closed limit’
INCREASING MOTOR SPEED
DECREASING MOTOR SPEED
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1
SPEED
INCREASED
Press for
1sec Press for 1sec
Press P2
for 1sec
LED
�ashes x5
beeps x3
LED
�ashes x1
beeps x1
LED
�ashes x1
beeps x1
SPEED
DECREASED
Press for
1sec Press for 1sec
Press P2
for 1sec
Note:
Three speed levels available. If the motor
does not response to these instructions, it
has already reached its upper speed setting.
Note:
Three speed levels available. If the motor
does not response to these instructions, it
has already reached its lower speed setting.

LED
�ashes x2
REMOTE
CONTROL
DEACTIVATED
Press P1
until LED
�ashes x2
LED
�ashes x8
beeps x4
FACTORY
SETTINGS
RESTORED
Press P1
for 14sec
ACTIVATING/DEACTIVATING ‘PULL TO START’ CONTROL
DEACTIVATING REMOTE CONTROL RESTORING FACTORY SETTINGS
LED
�ashes x3 Motor
beeps x1
LED
�ashes x5
beeps x3
Release
P1
Press for 1sec
within 10s
PULL TO
START
ACTIVATED/
DIACTIVATED
Press P1
for 10sec
Note:
‘Default setting: ‘Pull to start’ control activated.
Note:
To reactivate remote control,
press P1 button x1.
V1 - Sept 2023