Dedoes MPU02 User manual
Call or Visit @ 248-624-7710 / www.dedoes.com
PART # P2764 KD RV.0 - 2022-05-12
• Perform a pressure test after each repair or replacement of parts within the MPU02 before use to ensure there are no leaks.
• Turn both of the front pump valves to the "ON" position.
• Unscrew the wetting cup and set it aside.
• Visually check that both pump pistons go completely down within each pump and are adjusted correctly.
• Pour one quart of reducer in a container and place under front pump.
• Place both of the front pump suction hoses into the front container with the reducer.
• Pour one quart of reducer into a container and place under the rear pump.
• Place the rear pump suction hose into the rear container with the reducer.
• Pump the lever in quick short strokes making sure the lever is going completely down until both pumps are primed.
• Once the air is pumped out of the pumps, pump the lever one full stroke and verify that the pumps are working correctly.
• With the lever at the half stroke and reducer lling the pumps, block the end of one of the discharge tubes with your nger.
• Pull the lever down rmly and hold it down.
• Visually inspect the seals in each pump to be sure that uid does not by-pass the seals.
• Visually check all connections of the pump for any leakage. If none, lift lever slightly to release your nger.
• Verify that both pump assemblies and hose assemblies do not leak under pressure using the steps above.
• Pull the lever down completely.
• Remove the full container and replace it with an empty container.
• Pump the unit until both pumps are empty.
• Shake suction the hoses to drain as much uid as possible.
• Leave the hoses hanging to air dry.
• Wipe the unit o using paper towels.
• Screw the wetting cup in place.
• Place new product on the MPU02 and prime the pumps. (Refer to the user manual for priming instructions)
• Dispense enough uid to ensure the reducer has been ushed from MPU02 unit entirely.
• Dedoes suggests a spray panel test to verify clear coat nish quality.
Call or Visit @ 248-624-7710 / www.dedoes.com
P1891
SA0154
P2603
P0466
P0472
P0465
P0436
P0478
P1888
P0468
P1893
P0439
P0476
P0470
P0477
Call or Visit @ 248-624-7710 / www.dedoes.com
SA0255
rValve
P0444
P1892
P0435 Rod
Front Discharge
Hose
P0441D
Rear Discharge
Hose
SA0256
r
P0472
P0465
P0436
P0478
P1888
P0444
P0444
P0444
Call or Visit @ 248-624-7710 / www.dedoes.com
To assemble the new SA0153 PUMP ASSEMBLY to the front posi�on on MPU:
• Perform a pressure test to check for leaks prior to use. See page 1 for pressure test steps.
For rear pump replacement:
To assemble the new SA0153 PUMP ASSEMBLY to the rear posi�on on MPU:
• Perform a pressure test to check for leaks prior to use. See page 1 for pressure test steps.
SA0256
Call or Visit @ 248-624-7710 / www.dedoes.com
Removal of check valves.
Assembly of new check valves
• Perform a pressure test to check for leaks prior to use. See page 1 for Pressure test steps.
SA0256
Valve
SA0255
Call or Visit @ 248-624-7710 / www.dedoes.com
Rear Valves
SA0255
pressure.
SA0256
12 Hours
Call or Visit @ 248-624-7710 / www.dedoes.com
P1225
P0449
P1109*
P0454
P0440
P0458
P0464
P0451
P0445
P0440
Call or Visit @ 248-624-7710 / www.dedoes.com
rod
P1891.
P0436
P0478
P1888
P0465
P0466
P0472
P1893
SA0154
P2603
P0476
P0477
P0468
P0470
P1891
SA0256
SA0255
P0439
P0435 Rod
Call or Visit @ 248-624-7710 / www.dedoes.com
P0472
P1893
SA0154
P2603
P0476
P0477
Call or Visit @ 248-624-7710 / www.dedoes.com
READ THIS BEFORE ASSEMBLING THE TABLE
