Deenkee I7 User manual

Owner’s Manual
I7 Vacunm cleaner
Thank you for purchasing the product.
Please read the manual carefully before using.

Warnings
Instructions for use shall be provided with the appliance so that appliance
can be used safely.
The plug must be removed from the socket-outlet before cleaning or
maintaining the appliance.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and usermaintenance shall not be done by children without
supervision.
Children shall not play with the appliance.
Only to be used with the power supply unit provided with the appliance.
This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of theappliance in a safe way and understand the hazards
involved.
This appliance is intended for household use only.
- 01 -

Contents
1. Safety Instruction………………2-6 2. Product Formation………………7-8
3. Product Installation……………… 9 4. Product Usage…………………10-15
5. Product Maintenance……………15-18 6. Common Faults………………………19
7. Technical Parameters……………… 20
1.1 Use Notes
1.2 Safety Precautions
1.3 Child Safety
1.4 About Battery
1.5 Usable Range
1.6 Exception Clause
2.1 Main Body and Accessories
2.2 Accessories Introduction
4.1 Main body’s Usage
4.2 Charging Methods
4.3 Remote Control’s Usage
4.4Water Tank’s Usage
5.1 Daily Storage
5.2Cleaning of Charging Pole Pieces
5.3 Clean the Dust Box
5.4 Clean the Main Brush
5.5 Clean the Side Brush
5.6 Clean the Wheels
5.7 Clean the Sensors
- 02 -
4.5Magnetic Stripe’s Usage

Thank you for purchasing intelligent vacuum cleaner.
Wish you have a happy experience!
1.Safety Instruction
1.1 Use Notes
1.2 Safety Precautions
Before using the product, please observe the following safety precautions:
Read the instruction carefully; use the product according to the operation procedures.
Keep the instruction carefully, and look it up in the future.
If you want to give the product to others, please enclose the instruction.
Wrong operation will lead to serious personal injury and damage the product.
Caution
Only use the original adaptor, battery and charging station, or else it
will damage the machine and cause fire because of electric shock
and high voltage.
If you find that the main body and accessories are damaged, Please do
not use the cleaner and keep contact with the after-service dep artment
Anyone is not allowed to disassemble, maintenance or remould the
machine.
Do not touch the battery socket and the machine when your hands are
wet, or else it will cause electric shock.
Pull off the plug before doing the maintenance.
If the mains cord is destroyed, to avoid danger, please contact us and
wait for professional persons to replace it.
- 03 -

- 04 -
Attention
Switch off the cleaner
when taking out the
battery.
The machine is only used
indoor.
Prevent water, oil and
other liquid into the
machine.
Clean up the wire in the
floor, or else it will hinder
the working of the machine.
Charging station and
space isolator should be
against the wall and flat
place, or else the function
will be influenced.
Please remove all fragile
objects.
Please cut off the battery
socket, not used for a
long time.
If the docking station is
removed when works,it will
cause incapability of the
machine to recharge.
Don’t use this product without the protective guard if it is suspended
in the air so as to prevent the vacuum cleaner from falling accidentally
and causing personal injury.
Do not put the machine behind the fire, inflammable, explosive and
corrosive materials.
Do not put your clothes or any place of your body(hair, finger and so on)
into the main brush and wheels, or it will cause personal injury.
Danger!
Electric shock.

1.3 Child Safety
1.4 About Battery
1. The machine will only be used with the original battery.
2. Please turn off the power switch before taking out the battery.
3. The battery must be taken out before abandoning it.
4. If you want to replace the battery,please keep contact with our after service department.
It will lead to accident if wrong battery is put in the machine.
5. If the battery is leaked,please do not touch the liquid, wipe the liquid with dry cloth,and put
the battery to recycling bin or maintenance centre,do not throw it at random.
6. Please handle the old battery of the parts(remmote control).
The battery includes hazardous substance,please put it to recycle site according to original
environmental protection regulations.
The machine should not be used alone by children.
Forbid the children playing the poly bag, or else it will cause smother.
Please don’t collect
something sharp with the
device, such as glass sheet,
iron nail and others, for fear
of thedamage to the
product.
Please don’t use this cleaner
in humid or flammable,
explosive and corrosive
environments.
- 05 -

1.6 Exception Clause
Wooden Floor Tile Carpet
Applicable Range The cleaner is suitable to the following environment:
One of the following circumstances of the product is not in the range of free service.
Repair underpayment can be carried out:
A. The damage to the product arises out of the user’s operation and storage against our Manual;
B. The whole machine and its components have been out of the free warranty period;
C. The damage to the product arises out of the disassembly by the serviceman not sent or authorized
by our company;
D. The valid purchase invoice can’t be provided;
E. The model in the warranty card is inconsistent with that of the product for repair or is altered;
F. The damage to the product arises out of the irresistible factors such as natural disasters;
G. The failure or damage to the product arises out of accidental or human factors (including disoperation,
liquid feeding, improper insertion and pulling, scratch, handling, bumping, inappropriate voltage input, etc).
1.5 Usable Range
- 06 -

2. Product Formation
2.1 Main Body and Accessories
Main Body
*1pc
Tips:
Docking Station
*1pc
Battery
*1pc
Filter
*1pc
Screwdriver
*1pc
Side Brush
*2pcs
Clean Brush
*1pc
Adaptor
*1pc
Instruction
*1pc
* There is a battery, two side brushes and a filter assembled in main body, and another
two side brushes and one filter is inside.
Remote Control
*1pc
Water Tank +Mop
Cloth *1pc
Magnetic
Stripe*1pc
- 07 -
Thank you for purchasing the product.
Please read the manual carefully before using.
Owner’s Manual
I7 Vacunm cleaner

2.2 Accessories Introduction
Water Tank + Mop Mop
Cloth
Water Tank
- 08 -
Front View
Top Cover
Control Button
Signal Window
Dustbin Button
Front Shell
Battery
Left Wheel
Middle Brush
Bottom View
Side Brush
Right Wheel
Rubber Brush
Front Wheel

3.Product Installation
1. Connect the terminal of the battery pack to the machine; then press the battery pack downforwad into
the battery box.
2. Please put the docking station on the flat ground against the wall. Please clean up the dust and other
debris ,stick the dock station on floor. Next, inserting the adapter into the power socket.
Tips:
The docking station can’t be placed on the carpet. It is recommended to place it at a fixed
position for a long time. Please don't move the docking station artificially during the cleaning.
1. Place the docking station on the flat ground against to the wall. Make suer no obstacles ahead 3
meters and within 1 meter’s scope.
2. Connect the adapter and docking station .
- 09 -
Adapter Socket
Charging Terminal
Please install the battery before using the cleaner.
Red
Black
Aim at the terminal and insert
it during wiring.
Unplug it in the reverse
direction during unwiring.
1
1
Danger! Electric shock.

4.Product Usage
4.1.1 Introduction to Control Button
4.1.2.1 Manual Mode
4.1 Main body’s Usage
4.1.2 Work Mode
Auto Cleaning
Shortly-press the " " button ,the red indicator
will light(standby mode ).Then,click the button and the
indicator turn green,it will start cleaning automatically.
Auto Recharge
When the vacuum cleaner is in standby mode,
double click the " " button and then the indicator
turns green and blinks at the same time,which means
it enters auto-recharging mode.
CLEAN
CLEAN
Recharge Button
Turn On/off Button
In standby
Double click
Shortly press
Button Introduction
CLEAN
- 10 -

4.1.3 Operation guideline of indicators
4.2 Charging Methods
4.2.1 Manual Charging
2. Charging via the remote control:
When the cleaner is in standby mode,
press the " " button to have the machine
enter the recharge mode.
1. Charging with the docking station:
Connect the adapter to the docking station first, and
then insert to the power supply; Place the vacuum
cleaner on the docking station for charging. (The
green " " indicator will flash when looking for
dock station,the green indicator on dock station will
be off when charge back successfully; The red
" " indicator will flash during charging and
keep on after fully charged).
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
CLEAN
Turn-off1
2
3
4
5
6
7
8
Light-off
Red Light-on
Green Light-on
Flash Green
Flash Red
Flash Orange
Flash red and beep
Light off
Long-press " "4S and enter the
OFF state.
Short-press " " and enter the
Auto Cleaning mode.
In standby,long-press " " 6S till
orange " " blinks, meanwhile
press " " on remote control,till
beep sound heard
Double click " " and it will enter
the Recharge mode.
Short-press " " and enter the
Standby state.
Turn-on
Cleaning
Recharge
Charging
Error
Fully Charged
Pairing mode
No. State Display Operation
- 11 -
Danger!
Electric shock.

4.2.2 Auto Charging
Automatic Charging:
In low battery ,the green " " indicatorwill flash entering
the Recharge mode.
CLEAN
Tips:
1. Customers should operate the cleaner within 7 meters distance covered by WIFI signal with our
remote control; otherwise, the operation fails.
2. When press the “auto-recharge”button, the vacuum cleaner will may fail to return to the
charging base either because of complex surrounding obstacles or running-out-of batteries.
3. The cleaner will beep when receive a comand from remote control.
Single Room Cleaning
Start/Stop Auto cleaning
Right-turn button
Back button
Auto cleaning button
Left-turn button
Forward button
Auto-charging
Time setting
Scheduling
Edge cleaning button
4.3 Use of Remote Control
Introduction of remote control buttons
- 12 -

Start/Stop (button)
Right-turn button
Back button
Left-turn button
Forward button
Guidelines of Remote Control Use:
Function Guidelines
1. When the cleaner is in standby mode, press the button to enter the auto-cleaning mode.
2. When the cleaner is at any cleaning mode, press the button to shift it to standby mode.
3. When setting the time, press this button to hold settings.
Long-press the button and the cleaner will forward; releasing, it stops moving.
Long-press the button and the cleaner rotates counterclockwise; releasing, it stops.
Long-press the button and the cleaner rotates clockwise; releasing, it stops rotating.
Long-press the button and the cleaner moves backward less than 20cm before stop to
prevent it from falling off stairs or anywhere; releasing, it stops moving.
Function Information
Press the button to change the cleaner’s mode to auto-cleaning mode.
It will look for the charge station automatically when finish cleaning.
Press the button to change the cleaner’s mode to edge cleaning mode.
It will look for the charge station automatically when finish edge cleaning.
Press the button to change the cleaner’s mode to single-room cleaning mode.
It will look for the charge station automatically when finish the cleaning.
It will work for 30mins.in this mode.
1. In standby mode, press this button,the " " and " "on the display screen will
flash. Then press the up/down key to adjust the hour.
2. Press the left/right-turn key " "and " " to change into " "to adjust the minute.
3. Please save your settings by pressing the " "or " " key.
1. In standby mode, press this button,the " " and " " on the display screen will
flash. Then press the up/down key to adjust the hour.
2. Press the left/right-turn key " " and " " to change into " "to adjust the minute.
3. Please save your settings by pressing the " " or " ".
Pay attention to am or pm when set time.
Press the button to change the cleaner’s mode to recharging mode.
Auto Cleaning button
Edge Cleaning button
Single Room Cleaning
button
Time setting
Scheduling
Auto-charging
Function Guidelines Function Information
- 13 -

One way as below.
A.Turn on the cleaner entering standby mode with red light.
B.Press the" "button for 6s till orange light blinks,meanwhile,press" "button,
do not release both buttons till beep sounds heard.
Beep sounds mean paired.
Another way as below.
In off mode,press " " and " "at the same time for 3s,it is well paired when beep sounds heard .
Remarks:
If no beep sounds heard during above operations,it means failure of pairing.Pls repeat the above
methods.
Note:
If the remote control fails to respond, please check whether it’s it's in low
battery. If it is still not work after charge,then re-pair again in below methods.
CLEAN
CLEAN
Tips:
Water Tank is a product add-on. It is only suitable for work on flat floor. Please select
it according to the use environment.
4.4 Water Tank's Usage
Please install the Water Tank as shown in the figure above.
Step:
1. As shown in the picture, open the cover of the water tank and fill it with water.
2.The buckle position should be aligned on the machine when installing the water tank
components.
3.When the water tank is held perpendicular to the vacuum cleaner, please press down
gently, you hear "click", and water tank close to the bottom of the machine, installation
completes.
- 14 -

4.5 Magnetic Stripe’s Usage
1.Measure
and cut
Magnetic Stripe
to your desired
length.
2.Firmly place
Magnetic Stripe
on the ground to
create a barrier.
3. Vacuum Cleaner
will not pass over
the Magnetic
Stripe.
Note: Robotic Vacuum Cleaner might go half way over the Magnetic Stripe before the
sensor is triggered and it turn around.
5.1 Daily Storage
5.2 Cleaning of Charging Pole Pieces
5.3 Clean the Dust Box
5.3.1 Assembly and Disassembly of Dustbin
5. Product Maintenance
If do not use the cleaner for a long time please fully
charge the battery first and store it in a dry place.
1. Please turn off the power switch or disconnect the
power plug first.
2. Please clean the charging pole pieces monthly with
dry cloth.
3. Do not use oil for scrubbing.
Press and hold the dustbin button and then take out the dustbin.
- 15 -
Charging
Pole Pieces

5.3.2 Cleaning dustbin
1. Open the baffle first, and then pour out the dust.
Recommendation:the dustbin should be cleaned
periodically.
2. Please clean the dustbin with the cleaning
brush.
3. After take out the filter, wipe off the dust with
the cleaning brush.
4.The dustbin can be washed. Note: the dust box should be completely air-dried before re-inserting
cold air
hot air X
5. After cleaning, re-assemble the filter in the dustbin first, and then install the dustbin into the cleaner.
- 16 -

5.4 Clean the Main Brush
5.4.1 Disassemble the Main Brush
5.4.2 Cleaning the main brush and the rubber brush
3. Take out the middle brushes and its scraper assembly.
1. Push the locking-bar buckle and lift it upward. 2. Clutch the main brush and lift it upward.
1. Please clean the main brush and rubber brush
with the cleaning brush regularly.
2. Please remove the hair and other entanglements
on the main brush regularly.
- 17 -

5.7 Clean the Sensors
1. Unscrew the screws on the side brush
with a screwdriver.
2. Take out the side brush, tidy the hair and trash
on and inside the side brush base.
Clean the front, left and right wheels regularly with a cleaning brush.
After each cleaning work is completed, dry cotton cloth is used to dry the transparent plate to
prevent dust from being accumulated on the plate so as to affect the performance of this product.
5.5 Clean the Side Brush
5.6 Clean the Wheels
- 18 -
Ground
Monitoring
Sensors
IR Sensors

Tips: If corresponding faults cannot be removed, please contact our after service team.
6. Common Faults
Failure of device
taking off
The device takes off and stops in
1 second.
Failure of front
wheel
The front wheel gets stuck and
doesn’t rotate.
Failure of ground
inspection
There is a problem in the ground
inspection.
Low electricity of
battery
Battery power has been extremely
low (but not the critical point of
recharge voltage).
Failure of front
bumper
The impact switches on the left and
right front shells can’t be restored.
Failure of main
brush
The main brush wheel is overloaded
or under loaded.
Failure of side
brush
The side-sweeper wheel is overloaded
or under loaded.
Failure of wall
inspection
There is a problem in the wall
inspection.
Failure of fan The fan doesn’t rotate but with large
current.
Flash red light
twice with one
sound
Flash red light
three times with
one sound
Flash red light
four times with
one sound
Flash red light
five times with
one sound
Flash red light
six times with
one sound
Flash red light
seven times with
one sound
Flash red light
eight times with
one sound
Flash red light
nine times with
one sound
Flash red light
ten times with
one sound
Flash red light
eleven times with
one sound
Flash red light
twelve times with
one sound
Error-flash
indicator Fault Names Fault Forms Solutions
Failure of left
wheel
Failure of right
wheel
The left wheel doesn’t rotate and is
overloaded.
Please check if there are twisters on
the left wheel of the device.
Please check if there are twisters on
the right wheel of the device.
Please take the device back to the
floor. Don’t have it suspended in
the air.
Please check if there are twisters on
the small wheels of the front wheel.
Please check if the sensing window at
the bottom of the device is abnormally
shielded.
Please return the device to the docking
station for charging.
Please check if the device impact
buffer is normal or not.
Please check if there are foreign
matters on the main brush hairbrush
of the device.
Please check if there are things like
hair or cloth twine the side brush.
Please check if the transparent window
of the wall inspection is shielded or
obstructed by hair and cloth.
Please check if the blades of the fan
are loose or wrapped by hair and cloth.
Failure of charging The device can’t be powered or
show the charging state.
Flash red light
fourteen times
with one sound
Please check if the device is connected
with the docking station.
The right wheel doesn’t rotate and
is overloaded.
- 19 -