DEFA LedgeCircle RF User manual

1
www.defa.com
122577 EN Rev. E04 - 0920
LedgeCircle RF Manual
NB! Pleasendthemanualinotherlanguages
  onwww.defa.comorscantheQRcode.
Norsk Svensk

www.defa.com
2
RF Radar | MinMaxO󰀨
About the product
LedgeCircle®RFisaRadarMinMaxO󰀨ttingwithabuilt-inradiocommunication.Thiscombinationmakes
LedgeCircle®RFidealforapplicationslikestairwaysandcorridorswherethelightcanremaino󰀨orata
reducedlevelwhennooneispresent.
Before your start!
 - Readtheconnectionandcongurationinstructionsbeforeyoustartmounting!Thisprocessmay
  beeasiertodowiththettingsinfrontofyou.
 - NotethattheRadarsensormaybetriggeredbymotionontheothersideofdoorsandwindows.
  Adjustthesensitivity/rangeofsensorsaccordingtotheconditions.
 - LedgeCircle®RFttingscommunicateatthe868Mhzfrequency.Telecomantennasusingthe
  800Mhzand900Mhzbandsmaycausettingstobepermanentlyon.Thisismostlikelytooccur
  atthetopoorsofbuildingswithornearsuchantennas.
How it works
EachLedgeCircle®RFttingcanreceiveactivationsignalsfromupto30otherttingsandbesettorespond
eitherbyturningontotheMaxlevel(usually100%)ortotheselectedStandby/Minlevel(10,20,30or50%).
Byconguringthesensorandcommunicationsettings,aLedgeCircle®RFinstallationmaybesetuptobe-
haveinawidevarietyofways,dependingonyourneeds.Seefurtherinstructionsonconnectionand
congurationinthefollowingsections.
Radar activation - example 1:
AllconnectedttingsreactrespondtoactivationsignalsbyturningONtotheMaxlevel(100%).
MinMaxOnO󰀨mode.
100% 100% 100%
 - AllttingsareOFFbydefault.
 - TherstttingtodetectmotionsendsanactivationsignalandturnsONtotheMaxlevel.
 - Allconnectedttingsrespondtotheactivationsignalinthesameway.
 - Thisensuresthatthelightwillbeonwellaheadofthepersonmovingthroughthebuilding.

3
www.defa.com
RF Radar | MinMaxO󰀨
100% 100% 100%
 - Asapersonmovesthroughthebuilding,eachttingdetectsmotionandcontinuestosignalthe
  otherstostayon.
 - TheHoldPeriodandsubsequentStandbyPeriod(seeSensorManual)doesnotstartrunning
  untilnomoreactivationsignalsarereceived.
 - TheHoldandStandbyPeriodsstartrunningatthesametimeforallconnectedttings.
  Thismeansthattheyalsoturno󰀨atthesametime.
100% 100% 100%
 - SinceallconnectedLedgeCircle®RFttingsdetectmotionforwardactivationsignalstoeachother,
  theinstallationbehavesinthesamewaynomatterwhichttingrstdetectsmotion.
100% 100% 100%

Hold
Period
10% 10% 10%

Standby
Period
Off Off Off

Off
 - TheHoldPeriodstartswhenafterthelastdetection/activationsignalhasbeenreceived.Thelight
  remainsattheMaxlevelduringthisperiod.OncetheHoldPeriodexpiresthelightgoesdowntothe
  totheselectedMinlevelfortheStandbyPeriod.
 - Detectionrange,HoldandStandbyPerioddurationandStandbydimminglevelcanbecongured
  withtheremote.

www.defa.com
4
Off Off OffOff
Off Off OffOff
10% Off Off Off
100% 100% 100% 100%
1
Radar activation - example 2:
Groupedresponses.ConnectedttingsrespondeitherbyturningONtotheMaxlevelorbyturningONtothe
selectedStandby/Minlevel.MinMaxO󰀨mode.
- AllttingsintheinstallationareOFFbydefault.
- Therstconnectedttingtodetectmotionsends
 anactivationsignalandturnsontotheMaxlevel.
- Fittingsonthesameoorrespondtothe
 activationsignalinthesameway.
- Therstttingontheoorsaboveandbelow 
 respondbyturningONtotheselectedStandby/
 Minlevel,andtheStandbyPeriodstartsrunning.
Off Off OffOff
100% 100% 100% 100%
10% Off Off Off
100% 100% 100%100%
2- Apersonmovingtothesecondoorisdetected
 bythersttting,alreadyattheStandbyMinlevel.
- ThettinggoesfromtheselectedMinlevelto 
 100%andsendsanactivationsignal.
- Fittingsonthesecondoorrespondbyalso
 turningONtotheMaxlevel.
- Thestairwellttinginthethirdoorrespondsby
 turningONtotheselectedStandbylevel.
- ThettingsintherstoorremainattheMaxlevel
 forthedurationoftheHoldPeriod.
- Notethatwhenthettingsintherstoorarenot
 alreadyon(e.g.thepersonisleavingfromthe
 secondoor),thestairwellttingontherstoor
 willalsorespondbyturningONtotheselected
 Minlevel.
RF Radar | MinMaxO󰀨

5
www.defa.com
Off Off Off Off
100% 100% 100% 100%
10% 10% 10%10%
100% 100% 100% 100%
4
- Allttingsintherstoorturno󰀨atthesame 
 timewhentheStandbyPeriodexpires,except
 whentheStandbyPeriodissettoindenite
 (MinMaxmode/Eternitysign).
- Thettingsinthesecondoorgototheselected
 Standby/MinlevelforthedurationoftheStandby
 Period.
- Detectionrange,HoldandStandbyperiod
 durationandStandbydimminglevelcanbe
 conguredwiththeremote.
RF Radar | MinMaxO󰀨
10% 10% 10% 10%
100% 100% 100% 100%
100% 100% 100%100%
10% Off Off Off
3
- Asthepersoncontinuestomoveupthestairs,the
 ttingsonthoseoorsbehaveinthesameway.
- WhentheHoldPeriodexpiresforthettingson
 therstoor,theyturndowntotheselectedMin
 levelforthedurationoftheStandbyPeriod.
- SinceallconnectedLedgeCircle®RFttings
 detectmotionandforwardactivationsignalsto
 eachother,theinstallationbehavesinthesame
 waynomatterwhichttingrstdetectsmotion.

www.defa.com
6
How to set up your installation
TosetupyourLedgeCircle®RFinstallation,rstconsiderwherettingswillbeinstalled,whichttingsthat
shouldobeyeachotherandhowyouwanteachttingtorespondtoanactivationsignal.Youshouldalso
considerwhatdurationstheHoldandStandbyperiodsshouldhave,whatyouwanttheStandbydimming/
MinlightleveltobeandwhetheryoushouldadjusttheSensorSensitivityincertainttingstopreventthem
frombeingtriggeredbymotionbehinddoorsorwindows.
Connection
 - Setonettingaside.Thiswillbetherstttingthattheotherslearntoobey(Fitting1).
 - Inturn,pointtheremotetoeachoftheotherttingsandpressandholdthe“Learn/Erase”
  buttonontheremote.
 - WhenthettingsenterLearn-mode,theywillstarttobeeponcepersecond.
 - RepeatthisforallttingsyouwanttoreceiveactivationsignalsfromFitting1.
 - Eachttingwillremaininlearnmodefor3minutes,unlessmanuallycancelled.
 - Now,pointtheremotetotheFitting1andpress“Transmit”.
 - ThettingsinLearn-modewillconrmthatthepairinghasbeenestablishedbybeepingrapidly
  3times.TheywillnowallrespondtoactivationsignalsfromFitting1.
 - Tointerconnectallttings,nowpointtheremotetoFitting1andpressandholdthe“Learn/Erase”
  buttonuntilitentersLearn-mode.
 - Placettingsthathavecompletedthe"Transmit"tooneside,apartfromthosewhohavenot.
 - Nowselectanothertting(Fitting2)andtakeitoutofLearn-modebypointingtheremotetoitand
  pressingthe“Learn/Erase”button.
 - PointtheremotetoFitting2againandpress“Transmit”.
 - Asbefore,allttingsinlearnmodewillbeeprapidly3timestoconrmthatthepairingissuccessful.
 - Repeatabovestepsuntilallttingshavelearnttorespondtoactivationsignalsfromallotherttings.
Selecting responses
 - ResponsesareselectedwiththeRX100%andRXSTBY%buttonsontheremote.
 - ByselectingRXSTBY%thettingwillgotoyourselectedStandbydimming/Minlevelwhenactivated.
 - ThisalsomeansthatthettingwillgostraighttotheStandbyPeriod.OnceyourselectedStandby
  Perioddurationexpires,thettingwillturnOFF.
 - Pointtheremotetoeachttingandpressthebuttoncorrespondingwithyourpreferredresponse.
 - ThefactorysettingforLedgeCircle®RFttingsisRXSTBY%.
Mounting
 - NOTE!Pleasereadthesensorandcongurationinstructionsbeforemounting.
 - Beawarethateachttingasamaximumindoorcommunicationrangeof30meters.
 - Forinstructions,seetheseparatemountingmanualprovidedwitheachtting.
RF Radar | MinMaxO󰀨
Using the Remote Control, follow the procedure described below:
TheRotarySwitch
islocatedinside
thetting
RF grouping via Rotary Switch
ByselectingthesamechannelontheRotaryswitchforallttingsina
preferredgroupthegroupingisautomaticallycompleted.
Useascrewdrivertopointthearrowtotheselectedchannel.
Connect ttings, select responses
Tomakethesetupandconnectionprocedurease󰀩cientaspossible,placethettingsyouwishtoconnect
infrontofyou.

7
www.defa.com
Remote Control | RF Wireless
Description
TheHRC-11providesafastandeasywaytocustomizeLedgeCircle®RFttings.Alterthesettingsusingthe
functionsasdescribedbelow.Thexturewillemitabeepwhenanewsettinghasbeenreceived.
Permanent On/O󰀨 function
Press“ON/OFF”toselectpermanentONor
permanentOFFmode.Press“AUTO”,“RESET”to
quitthismode.
Auto Mode
Press“AUTO”toinitiateautomaticmode.Inthis
modethesensorandttingbehaveaccordingto
yourselectedsettings.
Reset function
Press“RESET”,torestoredefaultsettings.
Shift +
ThisfeatureisnotavailablewithLedgeCircle®RF
ttings.
Power output
Press"Power80%"toreducepowerinputto80%.
Thiscanbedoneduringtherstyearortherst
10,000hoursofuse,whenthelightoutputisusually
abovetherequiredamount.Notethatttingsmust
bereturnedto100%manually(withtheremote).
Scene programming
1. Press“Start”tobeginprogramming.
2. Chooseyoursettingsforthescenewiththeappropriatebuttons.
3. Press“Memory”tosavethecreatedsceneintheremotecontrol.
4. Press“Apply”tousethesceneineachtting.
Shift
Press"shift"tousesecondarybuttonvalues
markedinred."Shift-mode"isactivefor20
seconds.
Brightness +/-
UsethesebuttonstoadjustthelightOutputduring
theHoldPeriod.

www.defa.com
8
Standby Period (Standby Time)
Usethesebuttons(+Shiftforredvalues)tosettheStandbyPeriodto
0s/10s/1min/5min/10min/30min/1h/+.Use"0s"tosetthe
ttingstoOn/O󰀨mode(noStandbyPeriod).Use("+")tosetthe
ttingstoMinMaxmode.ThettingwillremainattheselectedMin
levelindenitely.
Hold Period (Hold Time)
UsethesebuttonstosettheHoldTimeto2s/30s/1min/5min/10min/
15min/20min/30min.TosetHoldTimeto30s/5min/15min/30min,
pressthe“Shift”buttonrst.
Standby dimming level
SettheStandbydimming/Minlevelto10%/20%/30%/50%.
Remote Control | RF Wireless
Dual Tech & RF mode
UsetheLearn/EraseandTransmitbuttonssetupconnections
betweenttings,see"Howtosetupyourinstallation"onpage
6.UseRX100%AndRXSTBY%toselectwhetherthetting
shouldgoto100%ortotheselectedStandbylightlevelvia
radiocommunication.
Factory settings:
-Sensitivity: 100%
-Holdperiod: 1min.
-Standbyperiod: 5min.
-Standbydimlevel: 20%
-Daylightthreshold: Disable
Detection range
Pressthesebuttonstosetdetectionrangeto100%/75%/50%/10%.