Deister electronic proxSafe locker User manual

locker-manual_en_896328_v200915
www.deister.com
proxSafe locker
Wiring and Installation Instructions

2
locker-manual_en_896328_v200915
Regulatory Notices
Hereby, deister electronic declares that the radio equipment type proxSafe locker is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address: http://go.deister.com/ce
Disclaimer
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmit-
ted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
prior written permission of deister electronic GmbH.
deister electronic GmbH reserves the right to make changes to any and all parts of this documentation with-
out obligation to notify any person or entity of such changes.
deister electronic GmbH is not able to supervise the observance of the instructions given in this manual as
well as the conditions and methods used during installation, operation and maintenance of the devices.
Therefore we disclaim liability and reject responsibility for any losses, damages or costs that are caused by
misapplication, installation, handling errors or faulty operation or related to the above in any other way.
deister electronic GmbH
Hermann-Bahlsen Str. 11
30890 Barsinghausen
Germany
Phone: [phone] - 51 61 11
Fax: [phone] - 51 62 17
E-Mail: [email protected]
Web: www.deister.com

3
locker-manual_en_896328_v200915
Contents
1. proxSafe locker overview............................................................................... 4
2. Required tools ............................................................................................... 5
3. Mechanical connection.................................................................................. 5
4. Mounting side walls .................................................................................... 10
5. Mounting the wall bracket ........................................................................... 14
6. Installing the backplane in the service compartment .................................... 17
7. System initialization..................................................................................... 26
8. keyTag removal and return.......................................................................... 28
8.1 Removal .......................................................................................................................... 28
8.2 Return ............................................................................................................................. 29
9. keyTag sealing/ de-sealing.......................................................................... 30
9.1 Sealing ............................................................................................................................ 30
9.2 De-sealing ....................................................................................................................... 31
10. Emergency opening..................................................................................... 32

4
locker-manual_en_896328_v200915
1. proxSafe locker overview
Model
locker
S12-10
locker
S12-8 T
locker
S12
locker
S12-10
locker
S14
Equipment
With 10 com-
partments
With 8 com-
partments and
an integrated
terminal
With 12 com-
partments
With 10 com-
partments and
an integrated
terminal
with 14 com-
partments
Weight
75 kg
70 kg
80 kg
75 kg
76 kg
Outer Dimen-
sions, WxHxD
250 x 1920 x
300 mm
250 x 1920 x
300mm
250 x 1920 x
300mm
250 x 1920 x
300mm
250 x 1920 x
300mm
Operating Temp.
+5….+50 °C
+5….+50 °C
+5….+50 °C
+5….+50 °C
+5….+50 °C
Relative Humidity
5 …95% non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing
Model
locker
S14-11
locker
L4
locker
L6
locker
L8
locker
M12
Equipment
With 11 com-
partments and
an integrated
terminal
With 4 com-
partments
With 6 com-
partments
With 8 com-
partments
With 12 com-
partments
Weight
77 kg
200 kg
200 kg
200 kg
140 kg
Outer Dimen-
sions, WxHxD
250 x 1920 x
300 mm
650 x 1920 x
530 mm
650 x 1920 x
530 mm
650 x 1920 x
530 mm
500 x 1920 x
300mm
Operating Temp.
+5….+50 °C
+5….+50 °C
+5….+50 °C
+5….+50 °C
+5….+50 °C
Relative Humidity
5 …95% non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing
5 …95 % non-
condensing

5
locker-manual_en_896328_v200915
2. Required tools
3. Mechanical connection
1. Put the locker columns that are supposed to be connected next to each other, but leave a small gap.

6
locker-manual_en_896328_v200915
2. Open the service compartments at the bottom of each locker. The required keys are fixed with tape on
each locker’s front. Each service compartment contains a connector and a mounting bracket to mount
the column to the wall.
3. Put the connector in place.

7
locker-manual_en_896328_v200915
4. Correctly placed connector.
5. The lockers can now be positioned right next to each other.

8
locker-manual_en_896328_v200915
6. To secure both lockers at the bottom, you need two of the provided hexagon socket screws.
7. Position one screw at the connector’s rear (shown in step 4) and secure it.

9
locker-manual_en_896328_v200915
8. Close-up: connector and rear screw. Secure the screw with your hand first.
9. Tighten the screw by using a hex key.

10
locker-manual_en_896328_v200915
10. Do the same with the front screw. The lockers are now connected.
4. Mounting side walls
1. Loosen the four screws used to fix the locker’s cover with the hex key (2 at the back, 2 at the front).

11
locker-manual_en_896328_v200915
2. Now you can remove the lockers’ covers.
3. Take one of the provided spacers and its corresponding screw.

12
locker-manual_en_896328_v200915
4. Screw the spacers by using a Phillips screwdriver into the corresponding bores. (6 spacers for each locker).
5. Mind an even distance between the six spacers (spread across the surface of the side wall).

13
locker-manual_en_896328_v200915
6. Insert the left side wall and push it down until it ends flush with the locker’s top. Do the same with the
right side wall.
7. Afterwards secure the lockers’ covers.

14
locker-manual_en_896328_v200915
5. Mounting the wall bracket
1. Place the wall bracket on the top of both lockers so that the bracket’s bores correspond to the ones on
the lockers.
2. Mark the bore position on the wall. The bracket can be secured with up to three screws.

15
locker-manual_en_896328_v200915
3. Drill a hole into the wall at the marked position. This example uses a 8 mm masonry drill.
4. To secure the bracket, use the provided screws and washers.

16
locker-manual_en_896328_v200915
5. Screw the bracket to both lockers at the corresponding positions. Thereby, the single columns are now a
connected unit.
6. Put the anchor into the hole and secure the bracket with a screw. Thereby, the unit cannot fall or be moved.

17
locker-manual_en_896328_v200915
6. Installing the backplane in the service compartment
1. Guide the network and mains cables through the back of the locker that is connected to the terminal. In
the service compartment you can find two additional cables marked with either “Master” or “Slave”. Pull
these cables out of the service compartment as well.
2. Guide the connection cable of the second locker through the appropriate hole into the service compartment of
the other locker and pull it out. Do the same if you connect multiple lockers with each other, you may require
additional extension cables.

18
locker-manual_en_896328_v200915
3. The next step requires the Ethernet adapter module - DEA 1 - with its corresponding screws and washers
to connect it to the corresponding contacts on the circuit board (View the red marks in the image).
4. Put the adapter on the circuit board as shown in the image. Press the adapter slightly down until it lies on
the corresponding contacts on the circuit board.

19
locker-manual_en_896328_v200915
5. Afterwards secure the Ethernet adapter from deister with the provided screws and washers.
6. To connect the grounding cable, loosen the hex nut at the backplane.

20
locker-manual_en_896328_v200915
7. The grounding cable has a blue terminal (view image). It is put above the existing cables with red termi-
nals and secured with the loosened hex nut.
8. Afterwards, guide the cable with the red terminal back into the service compartment. Remove the hex nut
from the thread, put the cable on it and secure it again with the hex nut.