Dell d400 - Latitude - Pentium M 1.3 GHz User manual

Dell™Latitude™D400ServiceManual
Before You Begin
Preparing to Work Inside the Computer
Recommended Tools
Computer Orientation
Screw Identification
Using the Dell Diagnostics
When to Use the Dell Diagnostics
Features of the Dell Diagnostics
Starting the Dell Diagnostics
System Components
Keyboard
Removing the Keyboard
Installing the Keyboard
Memory
Installing a Memory Module Under the Memory
Module/Modem Cover
Installing a Memory Module Under the Keyboard
Mini PCI Card
Modem
Hard Drive
Removing the Hard Drive
Installing the Hard Drive
Removing the Interposer
Replacing the Interposer
Docking Doors
Removing the Docking Doors
Installing the Docking Doors
Bluetooth™
Display
Removing the Display Assembly
Replacing the Display Latch
Palm Rest
Cooling Fan
Touch Pad
System Board
Removing the System Board
Replacing the System Board
Reserve Battery
Flashing the BIOS
Speakers
Battery Latch
Pin Assignments for I/O Connectors
USB Connector
Video Connector
Serial Connector
Dell D/Bay Connector
Mini Recommended Spares List
Notes, Notices, and Cautions
Information in this document is subject to change without notice.
©2003DellInc.Allrightsreserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and Latitude are trademarks of Dell Inc.; Microsoft and Windows are registered trademarks of Microsoft Corporation; Bluetooth is a
trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model PPT
October2003Rev.A02
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Before You Begin
Dell™Latitude™D400ServiceManual
Preparing to Work Inside the Computer
Recommended Tools
Computer Orientation
Screw Identification

Preparing to Work Inside the Computer




1. Ensure that the work surface is flat and clean to prevent scratching the computer cover.
2. Save any work in progress and exit all open programs.
3. Turn off the computer and all attached devices.

4. If the computer is connected to a docking device (docked), undock it.
5. Disconnect the computer from the electrical outlet.
6. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices.
7. Disconnect all other external cables from the computer.
8. Remove any installed PC Cards from the PC Card slot.
9. Close the display and turn the computer upside down on a flat work surface.

10. Slide and hold the battery-bay latch release on the bottom of the computer, and then remove the battery from the bay.


CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is
not covered by your warranty. Read and follow the safety instructions in the System Information Guide that came with the computer.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a microprocessor by its edges, not by its pins.
NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the computer operating
system, press and hold the power button for 4 seconds.
NOTICE: To avoid damaging the system board, you must remove the main battery before you service the computer.


Recommended Tools

The procedures in this manual require the following tools:
lPhillips screwdriver
lFlat-blade screwdriver
lSmall plastic scribe
lFlash BIOS update program floppy disk or CD

Computer Orientation



Screw Identification

When you are removing and replacing components, photocopy "Screw Identification" as a tool to lay out and keep track of the screws. The screw identification
chart provides the number of screws and their sizes.


1
back
2
right
3
front
4
left
keyboard
(two each)
modem
(one each)
hard drive
(four each)


Back to Contents Page



1428U

1428U

2864D
display removal
(six each)

4911U
display bezel
(six each)

7166P
display latch
(two each)

5H953
palm rest
(thirteen each)

4911U

(two each)


5H953
fan
(three each)

1428U
system board
(six each)

1428U
(one each, if a BIOS card is present)
1428U
speakers
(two each)

4911U





Back to Contents Page

Flashing the BIOS
1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.

2. Insert the BIOS update program floppy disk or CD, and turn on the computer.

Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the
computer automatically reboots.
3. Press <F2> during POST to enter the system setup program.
4. Press <Alt> and <F> to reset the computer defaults.
5. Press <Esc>, select Save changes and reboot, and press <Enter> to save configuration changes.
6. Remove the flash BIOS update program floppy disk or CD from the drive and restart the computer.


Back to Contents Page

NOTE: If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD.

Back to Contents Page

Bluetooth™


1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Turn the computer over, loosen the captive screw in the Bluetooth module cover, and remove the cover.



3. Remove the existing module:
a. Pull the Bluetooth module out of the slot.
b. Disconnect the cable from the module.



CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
1
Bluetooth module cover
0X737
2
captive screw

3
battery bay


4. Ensure that the front of the Bluetooth module (silver) is facing outward, and connect the cable to the module.
5. Insert the module into the slot.
6. Replace the cover and tighten the captive screw.

Back to Contents Page

1
Bluetooth connector

2
Bluetooth module (front)
2U381

Back to Contents Page

Using the Dell Diagnostics
When to Use the Dell Diagnostics
Features of the Dell Diagnostics
Starting the Dell Diagnostics

When to Use the Dell Diagnostics

Whenever a major component or device in your computer does not function properly, you may have a component failure. If you are experiencing a problem
withyourDell™computer,performthechecksinthe"SolvingProblems"sectionintheUser's Guide and run the Dell Diagnostics before you call Dell for technical
assistance. Running the Dell Diagnostics may help you to resolve the problem yourself quickly without having to contact Dell for assistance.

If you are experienced with computers and know what component(s) you need to test, select the appropriate diagnostic test group(s) or subtest(s). If you are
unsure about how to begin diagnosing a problem, see "Starting the Dell Diagnostics."

Features of the Dell Diagnostics

The Dell Diagnostics helps you to check your computer hardware without any additional equipment and without destroying any data. By using the diagnostics,
you can have confidence in the operation of your computer. If you find a problem that you cannot solve by yourself, the diagnostic tests can provide you with
important information you need when talking to Dell's service and support personnel.


The diagnostic test groups or subtests also have the following features:
lOptions that let you perform express, extended, or custom tests on one or all devices
lAn option that allows you to select tests based on a symptom of the problem you are having
lAn option that allows you to choose the number of times a test group or subtest is repeated
lThe ability to display test results
lOptions to temporarily suspend testing if an error is detected, or to terminate testing
lExtensive online Help that describes the tests and devices
lStatus messages that inform you whether test groups or subtests were completed successfully
lError messages that appear if any problems are detected

Starting the Dell Diagnostics

The Dell Diagnostics is located on a hidden Diagnostic utility partition on your hard drive.

1. Shut down the computer.
2. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.
3. Connect the computer to an electrical outlet.

NOTICE: Use the Dell Diagnostics to test only your Dell computer. Using this program with other computers may cause incorrect computer responses or
result in error messages.
NOTE: If your computer cannot display a screen image, contact Dell. See the User's Guide for contact information.
NOTE: If you do not see anything on your display, hold down the mute button and press the power button (instead of <F12>) to begin the Dell
Diagnostics. You do not need to highlight Diagnostics and press <Enter>. The computer automatically runs the Pre-boot System Assessment.

4. Turnonthecomputer.WhentheDELL™logoappears,press<F12>immediately.IfyouwaittoolongandtheMicrosoft®Windows®logo appears,
continue to wait until you see the Windows desktop. Then shut down your computer and try again.
5. When the boot device list appears, highlight Diagnostics and press <Enter>.

The computer begins to run the Pre-boot System Assessment, a series of embedded diagnostics that perform initial testing on your system board,
keyboard, hard drive, and display.
lDuring the assessment, answer any questions that appear.
lIf a component failure is detected, the computer stops and beeps. To stop the assessment and reboot to the operating system, press <N>; to
continue to the next test, press <Y>; to retest the component that failed, press <R>.
lIf failures are detected during the Pre-boot System Assessment, write down the error code(s) and contact Dell before continuing on to the Dell
Diagnostics. See the User's Guide for contact information.
lIf you receive a message stating that no Diagnostics utility partition has been found, follow the instructions on the screen to run the Dell
Diagnostics from your Drivers and Utilities CD.

If the Pre-boot System Assessment completes successfully, you receive the message Booting Dell Diagnostic Utility Partition. Press any key to
continue.
6. Press any key to start the Dell Diagnostics from the Diagnostics utility partition on your hard drive.
7. After the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want.


8. If a problem is encountered during a test, a message appears, displaying the error code and a description of the problem. Write down the error code
and problem description and follow the instructions on the screen. If you cannot resolve the error condition, contact Dell. See the User's Guide for
contact information.
9. If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information.

10. When you have finished running a test, close the screen to return to the Main Menu screen. To exit the Dell Diagnostics and reboot the computer, close
the Main Menu screen.
Back to Contents Page

NOTE: The Service Tag for your computer is located in the title bar of each screen.
Option
Function
Express Test
Performs a quick test of devices. The test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to
increase the possibility of tracing the problem quickly.
Extended
Test
Performs a thorough check of devices. The test typically takes 1 hour or more and requires you to answer questions periodically.
Custom Test
Tests a specific device. You can customize the tests to be run.
Symptom
Tree
Allows you to select tests based on a symptom of the problem you are experiencing. The option lists the most common symptoms.
Tab
Function
Results
Displays the results of the test and any error conditions encountered.
Errors
Displays error conditions encountered, error codes, and problem description.
Help
Describes the test and may indicate requirements for running the test.
Configuration
Displays your hardware configuration for the selected device.
The Dell Diagnostics obtains your configuration information for all devices from the system setup program, memory, and various internal
tests and displays the information in the device list in the left pane of the screen (see the User's Guide for information on the system setup
program). The device list may not display the names of all the components installed on your computer or all devices attached to your
computer.
Parameters
Allows you to customize the test by changing the test settings.

Back to Contents Page

Display
Removing the Display Assembly
Replacing the Display Latch

Removing the Display Assembly


1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Remove the battery.
3. Remove the hard drive.
4. Remove the center control cover.
5. Remove the two M2.5 x 6-mm screws next to each hinge.



6. Remove the two M2.5 x 6-mm screws from the display-feed flex cable hold-down board.
7. Use the pull-tab to disconnect the display-feed flex cable from its connector on the system board.
8. Move the display assembly to an upright position and pull it up out of the computer.

Replacing the Display Latch



CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
1
display-feed flex cable

2
M2.5 x 6-mm screws (6)
4911U
3
display-feed flex cable hold-down board

4
pull-tab

CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.

To replace the display latch, you must remove the whole bezel.
1. Follow the instructions in "Preparing to Work Inside the Computer."
2. Remove the hard drive.
3. Remove the keyboard.
4. Openthedisplay180degrees,andremovethetworubberscrewcovers,fourrubberscrewbumpers,andthesixM2.5x4-mm screws that secure the
bezel.



5. Use your fingers to carefully pry around the perimeter of the bezel until the bezel separates from the display assembly.
6. Remove the two display latch screws, and remove the display latch.




Back to Contents Page

1
rubber screw bumpers
6U549
2
bezel

3
rubber screw covers
2U940
4
M2.5 x 4-mm screws
7116P
1
M2 x 1.8-mm screws (2)
5H953
2
display latch

NOTICE: When you replace the bezel, ensure that the display cable is routed correctly.

Back to Contents Page

Docking Doors
Removing the Docking Doors
Installing the Docking Doors

Removing the Docking Doors


1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Gently bend the docking doors and lift them away from the computer base.




Installing the Docking Doors

Slide the side of the docking doors with the spring over the longer posts.

CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
1
docking doors
8X516




Back to Contents Page

1
docking doors with spring
8X516
2
longer post


Back to Contents Page

Cooling Fan


1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Remove any installed memory modules, smart card, modem, or PC Card.
3. Remove the hard drive.
4. Remove the keyboard.
5. Remove the display.
6. Remove the palm rest.
7. Remove the fan cable from the fan extender cable that runs under the system board.



8. Remove the three M2 x 5-mm screws that secure the cooling fan.
9. Lift out the cooling fan.

Back to Contents Page

CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
1
fan cable

2
M2 x 5-mm screws (3)
1428U

Back to Contents Page

Hard Drive
Removing the Hard Drive
Installing the Hard Drive
Removing the Interposer
Replacing the Interposer

Removing the Hard Drive







To remove the hard drive in the hard drive bay:
1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Turn the computer over, and remove the two M3 x 3-mm screws.




3. Slide the hard drive out of the computer.

Installing the Hard Drive
CAUTION: If you remove the hard drive from the computer when the drive is warm, do not touch the metal housing of the hard drive.
CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
NOTICE: To prevent data loss, turn off your computer before removing the hard drive. Do not remove the hard drive while the computer is on, in
standby mode, or in hibernate mode.
NOTICE: Hard drives are extremely fragile; even a slight bump can damage the drive.
NOTE: Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell.
NOTICE: When the hard drive is not in the computer, store it in protective, antistatic packaging. See "Protecting Against Electrostatic Discharge" in your
System Information Guide.
1
M3 x 3-mm screws (2)
2864D
2
hard drive
See Mini RSL

1. Remove the new drive from its packaging.

Save the original packaging for storing or shipping the hard drive.
2. Slide the hard drive into the bay until it is fully seated.
3. Replace and tighten the two M3 x 3-mm screws.
4. Use the Operating System CD to install the operating system for your computer.
5. Use the Drivers and Utilities CD to install the drivers and utilities for your computer.

Removing the Interposer
1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Remove the hard drive.
3. Remove the two M3 x 3-mm screws from the side of the hard drive, and remove the hard drive carrier.



4. Carefully remove the interposer by pulling it straight off the hard drive.



1
M3 x 3-mm screws (2)
2864D
2
hard drive carrier
7X499
1
interposer
8267R


Replacing the Interposer

1. Attach the hard drive carrier to the new hard drive, and replace the two M3 x 3-mm screws.
2. Carefully attach the interposer from the old hard drive by pushing it straight onto the hard drive. Ensure that the pins are oriented correctly. When the
interposer is attached correctly, four extra pins are on one side.



3. Install the hard drive.

Back to Contents Page

NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector.
1
interposer
8267R

Back to Contents Page

Keyboard
Removing the Keyboard
Installing the Keyboard

Removing the Keyboard


1. Follow the instructions in "Preparing to Work Inside the Computer" to remove the battery and prepare the computer for work.
2. Open the display approximately 180 degrees.
3. Use a plastic scribe or, if a plastic scribe is not available, carefully use a small flat-blade screwdriver to lift the notched right edge of the center control
cover, and pry the cover loose from the bottom case.



4. Remove the two M2 x 5-mm screws from the top of the keyboard.
5. Use the pull-tab to pull the keyboard up and out (toward the display) of the bottom case.

CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such
as the back panel) on the computer.
1
center control cover
5U447



6. Rest the keyboard face down on the palm rest.
7. Pull straight up on the pull-tab that is attached to the keyboard connector to disconnect the connector from the interface connector on the system
board.



Installing the Keyboard
1. Connect the keyboard connector to the interface connector on the system board.
2. Insert the five securing tabs on the keyboard into their respective slots in the palm rest.
3. Replace the two screws at the top of the keyboard.
4. Replace the center control cover and snap it down starting on the left side and working to the right side so that it is flush with the palm rest.

1
keyboard
P1290
2
keyboard pull-tab

3
M2 x 5-mm screws (2)
1428U
4
securing tabs (5)

1
pull-tab on keyboard
connector
2
keyboard connector