Dell Mobile Workstation Precision M2400 User manual

Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Notes, Notices, and Cautions
IfyoupurchasedaDELL™nSeriescomputer,anyreferencesinthisdocumenttoMicrosoft®Windows®operating systems are not applicable.
Information in this document is subject to change without notice.
©2008DellInc.Allrightsreserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell,Latitude, and the DELL logo are trademarks of Dell Inc.; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc., and is used by Dell
under license; Intel is a registered trademark of Intel Corporation in the U.S. and other countries; Microsoft, Windows, Windows Vista, and the Windows Vista start button logo are
either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
September2009Rev.A02
Troubleshooting
Working on Your Computer
Base Assembly
Hinge Covers
Hard Drive
WLAN/WiMax Card
WWAN Card
WPAN (UWB/BT) Card
FCM
Fan
Processor Heatsink Assembly
Processor Module
Memory
Coin-Cell Battery
Modular Drive
LED Cover
Keyboard
Modem
Right Speaker Grill/Fingerprint Reader Assembly
Palm Rest Assembly
Card Cage
1394 Card
RJ-11 Modem Connector
System Board Assembly
I/O Card
DC Power Cable
Battery Latch Assembly
Display Assembly
Flashing the BIOS
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates potential for property damage, personal injury, or death.

Back to Contents Page
1394 Card
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing the 1394 Card
Replacing the 1394 Card
Removing the 1394 Card


1. Follow the instructions in Before Working on Your Computer.

2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly).

3. Remove the modular drive (see Removing the Modular Drive).

4. Remove the hinge covers (see Removing the Hinge Covers).

5. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly).

6. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) or Removing the Display Assembly (E6400 ATG)).

7. Remove the LED cover (see Removing the LED Cover).

8. Remove the keyboard (see Removing the Keyboard).

9. Remove the right speaker grill (see Removing the Right Speaker Grill/Fingerprint Reader Assembly).

10. Remove the palm rest assembly (Removing the Palm Rest Assembly).

11. Remove the card cage (see Removing the Card Cage).

12. Disconnect the 1394 cable from the system board, and unroute the cable.

13. Remove the two M2 x 3 screws.

14. Lift the 1394 card up at an angle and remove it.
CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.
1
1394 cable connector
2
system board
3
M2 x 3 screws (2)
4
1394 card

Replacing the 1394 Card


1. Insert the 1394 card at a 45-degree angle to fit the connector into the base assembly. Use the alignment pins to seat into position.

2. Replace the two M2 x 3 screws.

3. Route and connect the 1394 cable to the system board.

4. Replace the card cage (see Replacing the Card Cage).

5. Replace the palm rest assembly (Replacing the Palm Rest Assembly).

6. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly).

7. Replace the keyboard (see Replacing the Keyboard).

8. Replace the LED cover (see Replacing the LED Cover).

9. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Assembly (E6400 ATG)).

10. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly).

11. Replace the hinge covers (see Replacing the Hinge Covers).

12. Replace the modular drive (see Replacing the Modular Drive).

13. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

14. Follow the procedures in After Working on Your Computer.
Back to Contents Page

CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.

Back to Contents Page
Base Assembly
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing the Bottom of the Base Assembly
Replacing the Bottom of the Base Assembly
Removing the Base Assembly
Replacing the Base Assembly

Removing the Bottom of the Base Assembly

1. Follow the procedures in Before Working on Your Computer.

2. Close the display and turn the computer upside down.

3. Loosen the captive screw.

4. Slide the bottom of the base assembly away from the hinge covers, and lift to remove the bottom of the base assembly.
Replacing the Bottom of the Base Assembly

1. Slide the bottom of the base assembly into place.

2. Tighten the captive screw.

3. Follow the procedures in After Working on Your Computer.
Removing the Base Assembly

1. Follow the procedures in Before Working on Your Computer.

2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly).

3. Remove the card in the WWAN/FCM card slot, if present (see Removing a WWAN Card or Removing an FCM from the WWAN/FCM Slot).

4. Remove the card from the WLAN/WiMax card slot, if present (see Removing the WLAN/WiMax Card).
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
1
hinges covers (2)
2
bottom of the base assembly
3
captive screw




5. Remove the hinge covers (see Removing the Hinge Covers).

6. Remove the card from the WPAN/UWB/FCM card slot, if present (see Removing a WPAN (UWB/BT) Card or Removing an FCM from the WPAN/UWB/FCM
Slot).

7. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly).

8. Remove the hard drive (see Removing the Hard Drive).

9. Remove the modular drive (see Removing the Modular Drive).

10. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) or Removing the Display Assembly (E6400 ATG)).

11. Remove the LED cover (see Removing the LED Cover).

12. Remove the keyboard (see Removing the Keyboard).

13. Remove the right speaker grill (see Removing the Right Speaker Grill/Fingerprint Reader Assembly).

14. Remove the palm rest assembly (see Removing the Palm Rest Assembly).

15. Remove the card cage (see Removing the Card Cage).

16. Remove the coin-cell battery (see Removing the Coin-Cell Battery).

17. Remove the system board (see Removing the System Board Assembly).

18. Remove the modem (see Removing the Modem).

19. Remove the RJ-11 modem connector (see Removing the RJ-11 Modem Connector).

20. Remove the I/O card (see Removing the I/O Card).
Replacing the Base Assembly

1. Replace the I/O card (see Replacing the I/O Card).

2. Replace the RJ-11 modem connector (see Replacing the RJ-11 Modem Connector).

3. Replace the modem (see Replacing the Modem).

4. Replace the system board (see Replacing the System Board Assembly).

5. Replace the coin-cell battery (see Replacing the Coin-Cell Battery).

6. Replace the card cage (see Replacing the Card Cage).

7. Replace the palm rest assembly (see Replacing the Palm Rest Assembly).

8. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly).

9. Replace the keyboard (see Replacing the Keyboard).

10. Replace the LED cover (see Replacing the LED Cover).

11. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Assembly (E6400 ATG)).

12. Replace the modular drive (see Replacing the Modular Drive).

13. Replace the hard drive (see Replacing the Hard Drive).

14. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly).

15. Replace the card in the WPAN/UWB/FCM card slot, if applicable (see Replacing a WPAN (UWB/BT) Card or Replacing an FCM).



16. Replace the hinge covers (see Replacing the Hinge Covers).

17. Replace the card from the WLAN/WiMax card slot, if applicable (see Replacing the WLAN/WiMax Card).

18. Replace the card from the WWAN/FCM card slot, if applicable (see Replacing a WWAN Card or Replacing an FCM).

19. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

20. Follow the procedures in After Working on Your Computer.

21. Flash update the BIOS (see Flashing the BIOS for more information).

22. Enter the system setup program to update the BIOS on the new system board with the computer Service Tag. For information on the system setup
program, see the Dell™TechnologyGuide on your computer or at support.dell.com.
Back to Contents Page

NOTE: If you use a BIOS update program disc to flash the BIOS, press <F12> before inserting the disc in order to set the computer to boot from the disc
for one time only. Otherwise, you must enter the system setup program to change the default boot order.

Back to Contents Page
Battery Latch Assembly
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing a Battery Latch Assembly
Replacing the Battery Latch Assembly
There are two battery latches, a left and a right, and each latch uses a unique latch assembly. The spring, screw, and release buttons are the same for the left
and right battery latches.
The removing and replacing procedures are primarily the same for the right and the left battery latch. The differences are noted for the instructions that are
different for the right and left battery latches.
Removing a Battery Latch Assembly


1. Follow the instructions in Before Working on Your Computer.

2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly).

3. Remove the hard drive (see Removing the Hard Drive).

4. Remove the modular drive (see Removing the Modular Drive).

5. Remove the hinge covers (see Removing the Hinge Covers).

6. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly).

7. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) or Removing the Display Assembly (E6400 ATG)).

8. Remove the LED cover (see Removing the LED Cover).

9. Remove the keyboard (see Removing the Keyboard).

10. Remove the right speaker grill (see Removing the Right Speaker Grill/Fingerprint Reader Assembly).

11. Remove the palm rest assembly (see Removing the Palm Rest Assembly).

12. Remove the card cage (see Removing the Card Cage).

13. Remove the system board (see Removing the System Board Assembly). Do not remove the wireless mini-cards, memory modules, or processor from the
system board.

14. Remove the modem (see Removing the Modem).

15. Remove the RJ-11 modem connector (see Removing the RJ-11 Modem Connector).

16. Remove the I/O card (see Removing the I/O Card).

17. Remove the M2 x 3-mm screw from the alignment bracket, and remove the battery latch assembly.


18. Remove the spring from the alignment bracket and set it aside until the assembly is ready to be reinstalled.
CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.
NOTICE: The spring is not secured to the alignment bracket and can be easily misplaced. When removing the battery latch assembly, place the
spring in a secure location until the assembly is ready to be reinstalled.

Replacing the Battery Latch Assembly


1. Place the spring on the alignment bracket.

2. Place the battery release button underneath the base assembly.
For the right battery latch assembly, slide the alignment bracket to the left to align the button with the hole in the alignment bracket.
For the left battery latch assembly, slide the alignment bracket to the right to align the button with the hole in the alignment bracket.

3. Replace the M2 x 3-mm screw.


4. Replace the I/O card (see Replacing the Battery Latch Assembly).

5. Replace the RJ-11 modem connector (see Replacing the RJ-11 Modem Connector).

6. Replace the modem (see Replacing the Modem).

7. Replace the system board (see Replacing the System Board Assembly).

8. Replace the card cage (see Replacing the Card Cage).

9. Replace the palm rest assembly (see Replacing the Palm Rest Assembly).

10. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly).

11. Replace the keyboard (see Replacing the Keyboard).

12. Replace the LED cover (see Replacing the LED Cover).

13. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Assembly (E6400 ATG)).

14. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly).

15. Replace the hinge covers (see Replacing the Hinge Covers).

16. Replace the modular drive (see Replacing the Modular Drive).

1
spring
2
alignment bracket
3
M2 x 3-mm screws (2)
4
battery release button
5
base assembly


CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.
NOTICE: The battery release button is keyed to ensure proper alignment. If you feel resistance, check the alignment of the release button.


17. Replace the hard drive (see Replacing the Hard Drive).

18. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

19. Follow the procedures in After Working on Your Computer.
Back to Contents Page


Back to Contents Page
Working on Your Computer
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Recommended Tools
Before Working on Your Computer
After Working on Your Computer
This document provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that:
lYou have performed the steps in Before Working on Your Computer.
lYou have read the safety information that shipped with your computer.
Recommended Tools
The procedures in this document may require the following tools:
lSmall flat-blade screwdriver
lPhillips screwdriver
lSmall plastic scribe
lFlash BIOS update (see the Dell Support website at support.dell.com)
Before Working on Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.






1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.

2. Shut down your computer.
lIn Windows XP, click Start®Shutdown®Shutdown.
lIn Windows Vista, click Start , click the arrow icon, and then click Shut Down to turn off your computer.

3. Disconnect your computer and all attached devices from their electrical outlets.


4. Disconnect any telephone or network cables from the computer.

NOTE: The color of your system and certain system components may appear differently than shown in this document.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as
authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not
authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal
surface, such as a connector on the back of the computer.
NOTICE: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal
mounting bracket. Hold a component such as a processor by its edges, not by its pins.
NOTICE: When disconnecting a cable, pull on the cable's connector or on its strain-relief loop, not on the cable itself. For cable connectors with
locking tabs, press inward on the locking tabs to release the connector. When connecting a cable, ensure that the connectors are correctly
oriented and aligned to avoid damage to the connector and/or the connector's pins.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
NOTICE: To disconnect a network cable, first unplug the cable from your computer, and then unplug it from the network wall jack.
NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer.


5. Turn the computer upside down.

6. Slide the battery release latches toward each other to lock them in an open position.

7. Slide the battery out of the battery bay.

8. Disconnect any external devices and remove any installed cards before working on your computer:
lTo remove any installed cards, such as an ExpressCard, see the Dell™TechnologyGuide on your computer or at support.dell.com.
lTo undock from a docking station, see the E-Port User's Guide or the E-Port Plus User's Guide on support.dell.com.
lTo remove a battery slice, see the documentation that shipped with your battery slice or on support.dell.com.
lTo remove a cool slice, see the documentation that shipped with your cool slice or on support.dell.com.
lTo remove a port cover from the E6400 ATG, lift up and ease the port cover away from the connectors along the back of the computer.

9. Turn the computer topside up, open the display, and press the power button to ground the system board.
After Working on Your Computer
After you have completed the replacement procedures, ensure you connect the external devices, cards, cables, etc. before turning on your computer.

1
battery
2
battery release latches (2)
1
bottom of computer
2
port cover
NOTE: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell
computers.

1. Connect any external devices, such as a port replicator, battery slice, or cool slice, and replace any cards, such as an ExpressCard.

2. To replace a port cover from the E6400 ATG, fit the port cover into the connectors on the back of the computer.

3. Connect any telephone or network cables to your computer.

4. Replace the battery. Slide the battery into the battery bay until it clicks into place.

5. Connect your computer and all attached devices to their electrical outlets.

6. Turn on your computer.
Back to Contents Page


Back to Contents Page
Flashing the BIOS
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Flashing the BIOS From a CD
Flashing the BIOS From the Hard Drive
If a BIOS-update program CD is provided with a new system board, flash the BIOS from the CD. If you do not have a BIOS-update program CD, flash the BIOS
from the hard drive.
Flashing the BIOS From a CD


1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.

2. Press <F12> before inserting the BIOS-update program CD so that you can set up the computer to boot from a CD for one time only. Otherwise, you
must enter the system setup program to change the default boot order.

3. Insert the BIOS-update program CD, and turn on the computer.

Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the
computer will automatically reboot.

4. Remove the flash BIOS update program CD from the drive.
Flashing the BIOS From the Hard Drive


1. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.

2. Turn on the computer.

3. Locate the latest BIOS update file for your computer at support.dell.com.

4. Click Download Now to download the file.

5. If the Export Compliance Disclaimer window appears, click Yes, I Accept this Agreement.
The File Download window appears.

6. Click Save this program to disk, and then click OK.
The Save In window appears.

7. Click the down arrow to view the Save In menu, select Desktop, and then click Save.
The file downloads to your desktop.

8. Click Close if the Download Complete window appears.
The file icon appears on your desktop and is titled the same as the downloaded BIOS update file.

9. Double-click the file icon on the desktop and follow the instructions on the screen.
NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage.
NOTICE: Do not interrupt this process once it begins. Doing so may cause system damage.
NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage.

Back to Contents Page


Back to Contents Page
Card Cage
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing the Card Cage
Replacing the Card Cage
Removing the Card Cage


1. Follow the procedures in Before Working on Your Computer.

2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly).

3. Remove the modular drive (see Removing the Modular Drive).

4. Remove the hinge covers (see Removing the Hinge Covers).

5. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly).

6. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) or Removing the Display Assembly (E6400 ATG)).

7. Remove the LED cover (see Removing the LED Cover).

8. Remove the keyboard (see Removing the Keyboard).

9. Remove the right speaker grill (see Removing the Right Speaker Grill/Fingerprint Reader Assembly).

10. Remove the palm rest assembly (Removing the Palm Rest Assembly).

11. If a card is in the card cage, remove the card.

12. Remove the two M2 x 3 screws.

13. Press down on the connector-end of the card cage, then grasp each side of the card cage and push it towards the back of the laptop.

14. Pivot the card cage up to a 45-degree angle, then lift it up from the connector and laptop.
Replacing the Card Cage

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
1
M2 x 3 screws (2)
2
card cage
3
connector





1. Holding the card cage at a 45-degree angle, attach the front of the card cage to the base assembly, then lower the card cage into place.

2. Replace the two M2 x 3 screws.

3. Replace the palm rest assembly (Replacing the Palm Rest Assembly).

4. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly).

5. Replace the keyboard (see Replacing the Keyboard).

6. Replace the LED cover (see Replacing the LED Cover).

7. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Assembly (E6400 ATG)).

8. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly).

9. Replace the hinge covers (see Replacing the Hinge Covers).

10. Replace the modular drive (see Replacing the Modular Drive).

11. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

12. Follow the procedures in After Working on Your Computer.
Back to Contents Page

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
1
M2 x 3 screws (2)
2
base assembly
3
front of card cage



Back to Contents Page
Coin-Cell Battery
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing the Coin-Cell Battery
Replacing the Coin-Cell Battery
Removing the Coin-Cell Battery


1. Follow the procedures in Before Working on Your Computer.

2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly).

3. Pry up the coin-cell battery to release the double-stick adhesive tape on the bottom of the coin-cell battery, then lift it out of the computer.

4. Disconnect the coin-cell battery cable from the system board.
Replacing the Coin-Cell Battery


1. Connect the coin-cell battery cable to the system board.

2. Insert the coin-cell battery into the computer:
If you are installing the same coin-cell battery you removed, slide the battery under the tab, then press down to seal the tape on bottom.
If you are installing a new coin-cell battery, first remove the adhesive backing paper from the coin-cell battery. Slide the battery under the tab, then
press down to seal the tape on bottom.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.
1
coin-cell battery
2
coin-cell battery cable
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.


3. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

4. Follow the procedures in After Working on Your Computer.
Back to Contents Page

1
coin-cell battery
2
coin-cell battery cable

Back to Contents Page
Processor Module
Dell™Latitude™E6400andE6400ATGand
MobileWorkstationPrecision™M2400ServiceManual
Removing the Processor Module
Replacing the Processor Module
Removing the Processor Module


1. Follow the instructions in Before Working on Your Computer.

2. Remove the bottom of the computer (see Removing the Bottom of the Base Assembly).

3. Remove the processor heatsink assembly (see Removing the Processor Heatsink Assembly).


4. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop.


CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.
1
processor module


NOTICE: To avoid damage to the processor, hold the screwdriver so that it is perpendicular to the processor when turning the cam screw.
1
ZIF socket
2
ZIF-socket cam screw
NOTICE: To ensure maximum cooling for the processor, do not touch the heat transfer areas on the processor heatsink assembly. The oils in your
skin can reduce the heat transfer capability of the thermal pads.


5. Lift the processor module from the ZIF socket.
Replacing the Processor Module




1. Align the pin-1 corner of the processor module with the pin-1 corner of the ZIF socket, then insert the processor module.
When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the
others, the module is not seated properly.


2. Tighten the ZIF socket by turning the cam screw clockwise to secure the processor module to the system board.

3. Replace the processor heatsink assembly (see Replacing the Processor Heatsink Assembly).

4. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly).

5. Follow the procedures in After Working on Your Computer.
Back to Contents Page

NOTICE: When removing the processor module, pull the module straight up. Be careful not to bend the pins on the processor module.
CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer.
NOTICE: Do not touch the processor die. Press and hold the processor down on the substrate on which the die is mounted while turning the cam
screw to prevent intermittent contact between the cam screw and processor.
NOTICE: Ensure that the cam lock is in the fully open position before seating the processor module. Seating the processor module properly in the
ZIF socket does not require force. A processor module that is not properly seated can result in an intermittent connection or permanent damage
to the microprocessor and ZIF socket.
NOTE: If a new processor is installed, you will receive a new heatsink assembly, which will include an affixed thermal pad, or you will receive a new
thermal pad along with a tech sheet to illustrate proper installation.
NOTE: The pin-1 corner of the processor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket.
1
ZIF socket
2
pin-1 corner
3
ZIF-socket cam screw


NOTICE: To avoid damage to the processor, hold the screwdriver so that it is perpendicular to the processor when turning the cam screw.