Dell UltraSharp 1907FPV User manual

Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/index.htm[8/7/2012 10:06:33 AM]
Dell™ 1907FPV Flat Panel Monitor User's Guide
About Your Monitor
Front View
Back View
Side View
Bottom View
Monitor Specifications
Cleaning Your Monitor
Using Your Adjustable Monitor Stand
Attaching the Stand
Organizing Your Cables
Using the Tilt, Swivel, and Vertical Extension
Removing the Stand
Setting Up Your Monitor
Connecting Your Monitor
Using the Front Panel
Using the OSD
Setting the Optimal Resolution
Using the Dell Soundbar (Optional)
Rotating Your Monitor
Changing the Rotation of Your Monitor
Rotating Your Operating System
Solving Problems
Troubleshooting Your Monitor
General Problems
Product Specific Problems
USB Problems
Troubleshooting Your Soundbar
Appendix
Safety Information
FCC Notice (U.S. Only)
Contacting Dell
Your Monitor Setup Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and
Dell OpenManage are trademarks of Dell Inc; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; Adobe is a
trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered trademark of the U.S.
Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for
energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model 1907FPV
November 2006 Rev. A02

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
Back to Contents Page
About Your Monitor
Dell™ 1907FPV Flat Panel Monitor User's Guide
Front View
Back View
Bottom View
Side View
Monitor Specifications
Cleaning Your Monitor
Front View
1. OSD menu / select button
2. Video input select / Down button
3. Auto-adjust / Up button
4. Power button (with power light indicator)
Back View

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
1VESA mounting holes (100mm) (Behind
attached base plate) Use to mount the monitor.
2Regulatory rating label List the regulatory approvals.
3Security lock slot Use a security lock with the slot to help secure your monitor.
4Dell Soundbar mounting brackets Attach the optional Dell Soundbar.
5Barcode serial number label Refer to this label if you need to contact Dell for technical support.
6Stand removal button Press to release the stand.
7Cable holder Help organize cables by placing them in the holder.
8Lock down/release button Push the monitor down, press the button to unlock the monitor, and then
lift the monitor to the desired height.
Bottom View
1 Power
connector Insert the power cable.
2Dell Soundbar
power
connector
Connect the power cord for the Soundbar (optional).
3DVI connector Connect your computer DVI cable.
4 VGA
connector Connect your computer VGA cable.
5USB upstream
connector Connect the USB cable that came with your monitor to the monitor and the computer. Once this cable is connected you can use the USB connectors on the side and bottom of the
monitor.
6 USB
connector Connect your USB devices.
NOTE: You can use this connector only after you connect the USB cable to the computer and the USB upstream connector on the monitor.
Side View

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
USB connectors (downstream)
Left side Right side
Monitor Specifications
Power Management Modes
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is
referred to as 'Power Save Mode'*. If input from keyboard, mouse, or other input devices is detected by the computer, the monitor automatically 'wakes up'. The following
table shows the power consumption and signaling of this automatic power saving feature:
VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption
Normal operation (with Dell Soundbar and USB active) Active Active Active Green 65 W (maximum)
Normal operation Active Active Active Green 32 W (typical)
Active-off mode Inactive Inactive Blanked Amber Less than 2 W
Switch off - - - Off Less than 1 W
NOTE: The OSD will only function in the 'normal operation' mode. One of the following messages will appear when the “menu” or “plus” buttons are pressed when in
Active-off mode.
1. Analog Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
or
2. Digital Input
In Power Save Mode
Press Computer Power Button
or Any Key on Keyboard or Move Mouse
Activate the computer and 'wake up' the monitor to gain access to the OSD.
This monitor is ENERGY STAR®-compliant as well as TCO '99 / TCO '03 power management compatible.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
Pin Assignments
15-pin D-Sub connector

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
Pin Number Monitor Side of the 15-pin Side Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 GND
5 DDC-GND
6 GND-R
7 GND-G
8 GND-B
9DDC +5V
10 Self Test
11 GND
12 DDC data
13 H-sync
14 V-sync
15 DDC clock
24-pin Digital-only DVI Connector
NOTE: Pin 1 is at the top right.
Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment
1T.M.D.S. Data 2- 9T.M.D.S. Data 1- 17 T.M.D.S. Data 0-
2T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+ 18 T.M.D.S. Data 0+
3T.M.D.S. Data 2/4 Shield 11 T.M.D.S. Data 1/3 Shield 19 T.M.D.S. Data 0/5 Shield
4No Connect 12 No Connect 20 No Connect
5No Connect 13 No Connect 21 No Connect
6DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7DDC Data 15 Self Test 23 T.M.D.S. Clock +
8No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock -
Universal Serial Bus (USB) Interface
This monitor supports High-Speed Certified USB 2.0 interface.
Data Rate Power Consumption
High speed 480 Mbps 2.5W (Max., each port)
Full speed 12 Mbps 2.5W (Max., each port)
Low speed 1.5 Mbps 2.5W (Max., each port)

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
USB ports:
1 upstream - rear
4 downstream - 2 on rear; 2 on left side
NOTE: USB 2.0 capability requires 2.0-capable computer.
NOTE: The USB interface of the monitor works ONLY when monitor is powered ON (or in Power Save Mode). Switching your monitor OFF and then ON would re-
enumerate its USB interface; attached peripherals may take a few seconds to resume normal functionality.
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data
(EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic; you can
select different settings, if desired.
General
Model number 1907FPV
Flat Panel
Screen type Active matrix - TFT LCD
Screen dimensions 19 inches (19-inch viewable image size)
Preset display area:
Horizontal 376 mm (14.8 inches)
Vertical 301 mm (11.85 inches)
Pixel pitch 0.294 mm
Viewing angle 170° (vertical) typ, 170° (horizontal) typ
Luminance output 250 CD/m ²(typ)
Contrast ratio 1000 to 1 (typ)
Faceplate coating Antiglare with hard-coating 3H
Backlight CCFL (4) edgelight system
Response Time 20 ms typical
Resolution
Horizontal scan range 30 kHz to 81 kHz (automatic)
Vertical scan range 56 Hz to 76 Hz (automatic)
Optimal preset resolution 1280 x 1024 at 60 Hz
Highest preset resolution 1280 x 1024 at 75 Hz
Preset Display Modes
Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock
(MHz) Sync Polarity (Horizontal/Vertical)
VESA, 720 x 400 31.5 70.0 28.3 -/+
VESA, 640 x 480 31.5 60.0 25.2 -/-
VESA, 640 x 480 37.5 75.0 31.5 -/-
VESA, 800 x 600 37.9 60.3 49.5 +/+

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
VESA, 800 x 600 46.9 75.0 49.5 +/+
VESA, 1024 x 768 48.4 60.0 65.0 -/-
VESA, 1024 x 768 60.0 75.0 78.8 +/+
VESA, 1152 x 864 67.5 75.0 108 +/+
VESA, 1280 x 1024 64.0 60.0 135.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
Electrical
Video input signals Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance
Synchronization input signals Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG (Composite SYNC on green)
AC input voltage / frequency / current 100 to 240 VAC / 50 or 60 Hz +3 Hz / 1.5A
Inrush current 120V:42A (Max.)
240V:80A (Max.)
Physical Characteristics
Connector type 15-pin D-subminiature, blue connector; DVI-D, white connector
Signal cable type Digital: Detachable, DVI-D, Solid pins, shipped detached from the monitor
Analog: Detachable, D-Sub, 15pins, shipped attached to the monitor
Dimensions (with stand):
Height (Compressed) 16.4 inches (416.75 mm)
Height (Extended) 21.5 inches (546.75 mm)
Width 16.35 inches (415.3 mm)
Depth 8.62 inches (218.9 mm)
Dimensions: (without stand)
Height 13.45 inches (341.6 mm)
Width 16.35 inches (415.3 mm)
Depth 2.81 inches (71.43 mm)
Stand dimensions:
Height (Compressed) 13.56 inches (344.56 mm)
Height (Extended) 18.54 inches (471.06 mm)
Width 11.84 inches (300.8 mm)
Depth 8.39 inches (213.1 mm)
Weight with packaging 21.1 lbs (9.55 kg)
Weight with stand assembly and cables 17.3 lbs (7.85 kg)
Weight without stand assembly
(For wall mount or VESA mount considerations - no cables)
11 lbs (5 kg)
Weight of stand assembly 5.2 lbs (2.35 kg)

About Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/about.htm[8/7/2012 10:06:38 AM]
Environmental
Temperature:
Operating 5° to 35°C (41° to 95°F)
Nonoperating Storage: -20° to 60°C (-4° to 140°F)
Shipping: -20° to 60°C(-4° to 140°F)
Humidity:
Operating 10% to 80% (noncondensing)
Nonoperating Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
Altitude:
Operating 3,657.6m (12,000 ft) max
Nonoperating 12,192 m (40,000 ft) max
Thermal dissipation 211.937 BTU/hour (maximum)
109.261 BTU/hour (typical)
Cleaning Your Monitor
CAUTION: Read and follow the safety instructions before cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
Use a slightly-dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.
If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.
Handle your monitor with care as darker-colored plastics may scratch and show white scuff marks more than lighter-colored monitor.
To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use.
Back to Contents Page

Using Your Adjustable Monitor Stand: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/stand.htm[8/7/2012 10:06:42 AM]
Back to Contents Page
Using Your Adjustable Monitor Stand
Dell™ 1907FPV Flat Panel Monitor User's Guide
Attaching the Stand
Organizing Your Cables
Using the Tilt, Swivel, and Vertical Extension
Removing the Stand
Attaching the Stand
NOTE: The stand is detached and extended when the monitor is shipped from the factory.
1. Fit the groove on the monitor to the three tabs on the stand.
2. Lower the monitor until it locks in to place on the stand.
Organizing Your Cables

Using Your Adjustable Monitor Stand: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/stand.htm[8/7/2012 10:06:42 AM]
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use
the cable holder to neatly organize all cables as shown above.
Using the Tilt, Swivel, and Vertical Extension
Adjusting Your Monitor Using Tilt, Swivel, and Vertical Extension. You can adjust your monitor to best fit your viewing needs.
You can adjust the stand vertically, up to 5.12 inches (130mm) using the stand lock/release button. You can adjust the
monitor to the desired position by sliding the monitor up and down the stand.
NOTE: Before you move the monitor to a new location, lock the stand by lowering monitor until in clicks in to place.
Removing the Stand

Using Your Adjustable Monitor Stand: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/stand.htm[8/7/2012 10:06:42 AM]
NOTE: After placing the monitor panel on a soft cloth or cushion, complete the following steps to remove the stand.
1. Rotate the stand to allow access to the stand release button.
2. Press the stand release button and lift up the stand and away from the monitor.
Back to Contents Page

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Back to Contents Page
Setting Up Your Monitor
Dell™ 1907FPV Flat Panel Monitor User's Guide
Connecting Your Monitor
Using the Front Panel
Using the OSD Menu
Setting the Optimal Resolution
Using the Dell Soundbar (Optional)
Connecting Your Monitor
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions.
or

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
1. Turn off your computer and disconnect the power cable.
2. Connect either the white DVI or blue VGA cables to the connectors on the computer and the monitor.
3. Connect the USB cable that was included with your monitor to the computer and the upstream USB connector on the monitor. Once this cable is connected to the
computer and the monitor, you can use the USB connectors on the monitor.
4. Connect any USB devices.
5. Connect the power cables.
6. Turn on your monitor and computer. If you do not see an image, push the input select button and ensure the correct input source is selected. If you still do not see an
image, see Troubleshooting your monitor.
Using the Front Panel
Use the buttons on the front of the monitor to adjust the image settings.
The Menu button is used to open and exit the on-screen display (OSD), and exit from menus and sub-menus. See Using
the OSD Menu.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
OSD menu / select
Video input select
Use the Input Select button to select between two different video signals that may be connected to your monitor.
NOTE: The floating 'Dell Self-test Feature Check' dialog appears on a black background if the monitor cannot
sense a video signal. Depending upon the selected input, one of the dialogs shown below will scroll continually.
or
Down (-) and Up (+)
Use these buttons to adjust (decrease/increase ranges) items in the OSD menu.
Auto Adjust
Use this button to activate automatic setup and adjustment. The following dialog appears on a black screen as the
monitor self-adjusts to the current input:
Auto Adjust In Progress
Auto Adjustment button allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment,
you can further tune your monitor by using the Pixel Clock (Coarse), Phase (Fine) controls in the OSD.
NOTE: Auto Adjust does not occur if you press the button while there are no active video input signals or attached
cables.
Power Button and Indicator
Use the power button to turn the monitor on and off.
The green light indicates the monitor is on, and fully functional. An amber light indicates power save mode.
Using the OSD Menu
NOTE: If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor automatically saves those changes. The changes are also
saved if you change the settings and then wait for the OSD menu to disappear.
1. Push the MENU button to open the OSD menu and display the main menu.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Main Menu for Analog (VGA) Input Main Menu for Digital (DVI) Input
or
NOTE: Positioning and Image Settings are only available when you are using the analog (VGA) connector.
2. Push the -and +buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table below for a complete list
of all the options available for the monitor.
3. Push the MENU button once to activate the highlighted option.
4. Push - and + button to select the desired parameter.
5. Push MENU to enter the slide bar and then use the -and +buttons, according to the indicators on the menu, to make your changes.
6. Push the MENU button once to return to the main menu to select another option or push the MENU button two or three times to exit from the OSD menu.
Icon Menu and
Submenus Description
Exit Select to exit the Main menu.
Brightness/
Contrast Brightness adjusts the luminance of the backlight.
Adjust Brightness first, then adjust Contrast only if further adjustment is necessary.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Push the +button to increase luminance and push the -button to decrease luminance (min 0 ~ max 100).
Contrast adjusts the degree of difference between darkness and lightness on the monitor screen.
Push the +button to increase the contrast and push the -button to decrease the contrast (min 0 ~ max 100).
NOTE: When using DVI source, the contrast adjustment is not available.
Positioning:
Horizontal
Vertical
Positioning moves the viewing area around on the monitor screen.
When making changes to either the Horizontal or Vertical settings, no changes occur to the size of the viewing area. The image
shifts in response to your selection.
Minimum is 0 (-) and maximum is 100 (+).
NOTE: When using DVI source, the Positioning option is not available.
Image settings:
Auto Adjust
Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for
use with your particular setup.
Select to activate automatic setup and adjustment. The following dialog appears on a black screen as the monitor self-adjusts to
the current input:
Auto Adjust In Progress
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune
your monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.
NOTE: In most cases, Auto Adjust produces the best image for your configuration.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Pixel Clock
(Coarse)
Phase (Fine)
The Phase and Pixel Clock adjustments allow you to more closely adjust your monitor to your preference. These settings are
accessed through the main OSD menu, by selecting Image Settings.
Use the -and +buttons to make adjustments. (Minimum: 0 ~ Maximum: 100)
If satisfactory results are not obtained using the Phase adjustment, use Pixel Clock (Coarse) and then use Phase (fine), again.
NOTE: This function may change the width of the display image. Use the Horizontal function of the Position menu to
center the display image on the screen.
NOTE: When using DVI source, the Image Settings option is not available.
Color Settings
Color Settings adjusts the color temperature, color hue, and saturation.
The color hue is most noticeable in areas of white.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Blue Preset
Red Preset
Normal Preset
User Preset
Blue Preset is selected to obtain a bluish tint. This color setting is typically used for text based applications (spreadsheets,
programming, text editors, etc.).
Red Preset is selected to obtain a redder tint. This color setting is typically used for color-intensive applications (photograph
image editing, multimedia, movies, etc.).
Normal Preset is selected to obtain the default (factory) color settings. This setting is also the “sRGB” standard default color
space.
User Preset: Use the plus and minus buttons to increase or decrease each of the three colors (R, G, B) independently, in
single digit increments, from 0 to 100.
OSD Settings:
Horizontal
Position
Vertical Position
OSD Hold Time
OSD Rotation
OSD Lock
Adjust the settings for the OSD, including the location, the amount of time the menu remains on-screen, and the rotation of the
OSD.
Position of the OSD:
To adjust the horizontal position of the OSD, use the -and +buttons, and move OSD to the left and right.
To adjust the vertical position of the OSD, use the -and +buttons, and move OSD down and up.
OSD Hold Time:
The OSD stays active for as long as it is in use. Adjusting the hold time, sets the length of time the OSD remains active after the
last time you pressed a button. Use the -and +buttons to adjust the slider in 5 second increments, from 5 to 60 seconds.
OSD Rotation:
Rotates the OSD by 90 ° counter-clockwise. Adjust according to Rotating Your Monitor setction
OSD Lock:
Controls user access to adjustments. When Yes (+) is selected, no user adjustments are allowed. All buttons are locked except the
menu button.
NOTE: When the OSD is locked, pressing the menu button takes the user directly to the OSD settings menu, with OSD
Lock selected. Select No (-) to unlock and allow user access to all applicable settings.
NOTE: You can also lock or unlock the OSD by pushing and holding the Menu button for 15 seconds.
Language Select to have the OSD display in one of five languages (English, French, Spanish, German, or Japanese).

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
NOTE: The change only affects the OSD. It has no effect on any software running on the computer.
Audio (optional) You can select to have the audio on or off when the monitor is in power saving mode.
Yes — enables audio
No — disables audio (default)
NOTE: When the Dell Soundbar is not properly connected to the monitor, the audio menu is not available.
Factory Reset: Reset the OSD menu options to the factory preset values.

Setting Up Your Monitor: Dell™ 1907FPV Flat Panel Monitor User's Guide
file:///T|/htdocs/monitors/1907FPV/en/setup.htm[8/7/2012 10:06:54 AM]
Exit — Select to exit out of Reset to Factory Settings menu without resetting any OSD options.
Position settings only — Change the settings for Image Position back to original factory settings.
Color settings only — Change the Red, Green, and Blue settings back to their original factory settings and set the default
setting for Normal Preset.
All settings — Change all the user-adjustable settings including color, position, brightness, contrast and OSD hold time to the
factory defaults. The language of the OSD does not change.
DDC/CI — Enable the DDC/CI control function.
DDC/CI (Display Data Channel/Command Interface) allows you to adjust the monitor parameters (brightness, color balance, etc)
via software applications on your PC.
Default is "Enable". You can disable this feature by selecting "Disable".
For best user experience and optimum performance of your monitor, keep this feature enabled.
NOTE: If user select "Disable", display Warning message box as below. Select "Yes" disable DDC/CI
and return to "Factory Reset" menu. Warning message time-out in 20 sec.
OSD Warning Messages
One of the following warning messages may appear on the screen indicating that the monitor is out of synchronization.