Dell External OEMR R210II User manual

Dell PowerEdge
R210 II Systems
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema

Dell PowerEdge
R210 II Systems
Getting Started
With Your System
Regulatory Model: E10S Series

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data
if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
___________________
Information in this publication is subject to change without notice.
© 2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.
Intel®is a registered trademark and Core™ is a trademark of Intel Corporation in the U.S. and
other countries. Microsoft®and Windows Server®are either trademarks or registered trademarks
of Microsoft Corporation in the United States and/or other countries. Red Hat®and Red Hat Enterprise
Linux®and are registered trademarks of Red Hat, Inc. in the United States and/or other countries.
SUSE ™ is a trademark of Novell, Inc. in the United States and other countries. Citrix®and
XenServer®are either registered trademarks or trademarks of Citrix Systems, Inc. in the United States
and/or other countries. VMware®is a registered trademarks or trademark of VMWare, Inc. in the
United States or other countries.
Other trademarks and trade names may be used in this publication to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
Regulatory Model E10S Series
December 2010 P/N RGTPR Rev. A00

Getting Started With Your System 3
Installation and Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with the system.
Unpacking the System
Unpack your system and identify each item.
Installing the Rails and System in a Rack
CAUTION: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified by
the manufacturer.
For more information, see "Technical Specifications" on page 9.
Assemble the rails and install the system in the rack following the safety
instructions and the rack installation instructions provided with your system.

4Getting Started With Your System
Optional—Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable
to plug into each connector. Be sure to tighten the screws (if any) on the
monitor's cable connector.
Connecting the Power Cable
Connect the system’s power cable to the system and, if a monitor is used,
connect the monitor’s power cable to the monitor.

Getting Started With Your System 5
Securing the Power Cable
Bend the system power cable as shown in the illustration and secure the cable
in the retention clip.
Plug the other end of the power cable into a grounded electrical outlet or
a separate power source such as an uninterrupted power supply (UPS) or
a power distribution unit (PDU).
Turning On the System
Press the power button on the system and the monitor. The power indicators
should light.

6Getting Started With Your System
Installing the Optional Bezel
Install the bezel (optional).
Complete the Operating System Setup
If you purchased a preinstalled operating system, see the operating system
documentation that ships with your system. To install an operating system for
the first time, see the installation and configuration documentation for your
operating system. Be sure the operating system is installed before installing
hardware or software not purchased with the system.
Supported Operating Systems
• Microsoft Small Business Server 2011 Standard and Essential Editions
• Microsoft Windows Server 2008 R2 SP1 (x64) Web, Standard,
Foundation, and Enterprise Editions
• Microsoft Windows
Server 2008 R2 (x64) Web, Standard, Foundation,
and Enterprise Editions
• Microsoft Windows Server 2008 SP2 (x86) Web, Standard,
and Enterprise Editions
• Microsoft Windows Server 2008 SP2 (x64) Web, Standard,
and Enterprise Editions
• Microsoft Windows Server 2008 R2 SP1(x64) with Hyper-V for
Standard and Enterprise Editions

Getting Started With Your System 7
• Microsoft Windows Server 2008 R2 (x64) with Hyper-V for Standard and
Enterprise Editions
• Microsoft Windows Server 2008 SP2 (x64) with Hyper-V for Standard and
Enterprise Editions
• VMware ESX 4.1 Update 1 (Classic)
• VMware ESX 4.1 Update 1 (Embedded)
• Citrix XenServer 5.6 Feature Pack 1
• Red Hat Enterprise Linux
6.0 (x86_64)
• SUSE Linux Enterprise Server 11 SP1 (x86_64)
NOTE: For the latest information on supported operating systems,
see support.dell.com.
Dell Software License Agreement
• Before using your system, please read the Dell Software License
Agreement that came with your system.
• You must consider any CD, DVD, or diskette set of Dell installed
software as BACKUP copies of the software installed on your system's
hard-disk drive.
• If you do not accept the terms of the agreement, please call the customer
assistance telephone number. For customers in the United States,
call 800-WWW-DELL (800-999-3355). For customers outside the
United States, visit
support.dell.com and select your country or region
from the top of the page.

8Getting Started With Your System
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with
your system. Warranty information may be included within this document
or as a separate document.
• The rack documentation included with your rack solution describes how
to install your system into a rack.
•The
Owner’s Manual provides information about system features
and describes how to troubleshoot the system and install or replace
system components. This document is available online at
support.dell.com/manuals .
• Any media that ships with your system that provides documentation and
tools for configuring and managing your system, including those pertaining
to the operating system, system management software, system updates,
and system components that you purchased with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does
not perform as expected, see your Owner’s Manual. Dell offers
comprehensive hardware training and certification. See dell.com/training
for more information. This service may not be offered in all locations.

Getting Started With Your System 9
Technical Specifications
Processor
Processor type One Intel Core processor i3-2100 product family
or
One Intel Xeon processor E3-1200 product family
or
One Intel Pentium processor (when available)
Expansion Bus
Bus type PCI Express Generation 2
Expansion slots One full-height, half-length x16 link
Memory
Architecture 1066 MHz and 1333 MHz DDR3 unbuffered
Error Correcting Code (ECC) DIMMs
Memory module sockets Four 240-pin
Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB
Minimum RAM 1 GB
Maximum RAM 32 GB
Drives
Hard drives Up to two 3.5-inch cabled SAS or SATA
internal drives
or
Up to two 2.5-inch cabled SAS or SATA
internal drives
Optical drive One optional internal SATA DVD-ROM or
DVD+/-RW drive
NOTE: DVD devices are data only.
Optional external USB DVD-ROM

10 Getting Started With Your System
Connectors
Back
NIC Two RJ-45 (for integrated 1 GB NICs)
Serial 9-pin, DTE, 16550-compatible
USB Two 4-pin, USB 2.0-compliant
Video 15-pin VGA
eSATA One 7-pin connector
Front
Video 15-pin VGA
USB Two 4-pin, USB 2.0-compliant
Internal
USB Two 4-pin, USB 2.0-compliant
Video
Video type Matrox G200, integrated in Winbond WPCM450
Video memory 8 MB
Power
AC power supply (per power supply)
Wattage 250 W
Voltage 100 VAC–240 VAC, 50 Hz/60 Hz, 4.0 A–2.0 A
Heat dissipation 1040 BTU/hr maximum
Maximum inrush current Under typical line conditions and over the entire
system ambient operating range, the inrush
current may reach 25 A
Batteries
System battery CR 2032 3.0-V lithium coin cell

Getting Started With Your System 11
Physical
Height 4.24 cm (1.67 inches)
Width 43.4 cm (17.09 inches)
Depth 39.37 cm (15.5 inches)
Weight
(maximum configuration)
8.058 kg (17.77 lb)
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see dell.com/environmental_datasheets.
Temperature
Operating 10 °C to 35 °C (50 °F to 95 °F) with a maximum
temperature gradation of 10 °C per hour
NOTE: For altitudes above 2950 feet, the maximum
operating temperature is derated 1 ºF/550 ft.
Storage –40 °C to 65 °C (–40 °F to 149°F) with a
maximum temperature gradation of 20 °C
per hour
Relative humidity
Operating 20% to 80% (noncondensing) with a maximum
humidity gradation of 10% per hour
Storage 5% to 95% (noncondensing)
Maximum vibration
Operating 0.26 Grms at 5 Hz–350 Hz for 15 min
Storage 1.87 Grms at 10 Hz–500 Hz for 15 min

12 Getting Started With Your System
Maximum shock
Operating One shock pulse in the positive z axis (one pulse
on each side of the system) of 31 G for 2.6 ms in
the operational orientation
Storage Six consecutively executed shock pulses in
the positive and negative x, y, and z axes
(one pulse on each side of the system) of 71 G for
up to 2 ms
Six consecutively executed shock pulses in the
positive and negative x, y, and z axes (one pulse
on each side of the system) of 32 G faired
square wave pulse with velocity change at
270 inches/second (686 centimeters/second)
Altitude
Operating –16 m to 3048 m (–50 ft to 10,000 ft)
NOTE: For altitudes above 2950 feet, the maximum
operating temperature is derated 1 ºF/550 ft.
Storage –16 m to 10,600 m (–50 ft to 35,000 ft)
Airborne Contaminant Level
Class G1 as defined by ISA-S71.04-1985
Environmental (continued)

Systèmes
Dell PowerEdge R210 II
Guide de mise en route
Modèle réglementaire : série E10S

Remarques, précautions et avertissements
REMARQUE : Une REMARQUE indique des informations importantes qui peuvent
vous aider à mieux utiliser votre ordinateur.
PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque d'endommagement
du matériel ou de perte de données en cas de non-respect des instructions.
AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement
du matériel, de blessures corporelles ou même de mort.
___________________
Les informations que contient cette publication sont sujettes à modification sans préavis.
© 2010 Dell Inc. Tous droits réservés.
La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.
est strictement interdite.
Marques utilisées dans ce document : Dell™, le logo DELL et PowerEdge™ sont des marques de
Dell Inc. Intel®est une marque déposée et Core™ est une marque d'Intel Corporation aux États-Unis
et dans d'autres pays. Microsoft® et Windows Server®sont des marques ou des marques déposées de
Microsoft Corporation aux États-Unis et/ou dans d'autres pays. Red Hat®et Red Hat Enterprise Linux®
sont des marques déposées de Red Hat, Inc. aux États-Unis et/ou dans d'autres pays. SUSE™ est une
marque de Novell, Inc. aux États-Unis et dans d'autres pays. Citrix®et XenServer®sont des marques
déposées ou des marques de Citrix Systems, Inc. aux États-Unis et/ou dans d'autres pays. VMware®
est une marque déposée ou une marque de VMware, Inc. aux États-Unis et dans d'autres pays.
D'autres marques et noms commerciaux peuvent être utilisés dans ce document pour faire référence
aux entités se réclamant de ces marques et de ces noms ou à leurs produits. Dell Inc. rejette tout intérêt
propriétaire dans les marques et les noms commerciaux autres que les siens.
Modèle réglementaire : série E10S
Décembre 2010 N/P RGTPR Rév. A00

Guide de mise en route 15
Installation et configuration
AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous,
lisez les consignes de sécurité fournies avec le système.
Déballage du système
Sortez le système de son emballage et identifiez chaque élément.
Installation des rails et du système dans un rack
PRÉCAUTION : Si le système est installé dans un rack clos ou multi-unités,
la température ambiante du rack lors du fonctionnement du système peut être plus
élevée que celle de la pièce. Il est donc important de veiller à installer l'équipement
dans un environnement compatible avec la température ambiante maximale (Tma)
spécifiée par le fabricant.
Pour plus d'informations, voir « Caractéristiques
techniques » à la page 21.
Assemblez les rails et installez le système dans le rack en suivant les consignes
de sécurité et les instructions d'installation du rack fournies avec votre
système.

16 Guide de mise en route
Facultatif : connexion du clavier, de la souris et du moniteur
Connectez le clavier, la souris et le moniteur (facultatif).
Aidez-vous des icônes des connecteurs situés à l'arrière du système pour
savoir où insérer chaque câble. N'oubliez pas de serrer les vis situées sur
le connecteur du câble du moniteur, s'il en est équipé.
Branchement du câble d'alimentation
Branchez le câble d'alimentation au système et, si vous utilisez un moniteur,
branchez son câble d'alimentation.

Guide de mise en route 17
Fixation du câble d'alimentation
Pliez le câble d'alimentation comme le montre l'illustration et faites-le passer
dans le clip de fixation.
Branchez ensuite l'autre extrémité du câble d'alimentation sur une prise
secteur mise à la terre ou sur une source d'alimentation autonome (onduleur
ou unité de distribution de l'alimentation).
Mise sous tension du système
Appuyez sur le bouton d'alimentation du système et sur celui du moniteur.
Les voyants d'alimentation s'allument.

18 Guide de mise en route
Installation du cadre en option
Installez le cadre (en option).
Finalisation de l'installation du système
d'exploitation
Si vous avez acheté un système d'exploitation préinstallé, consultez la
documentation connexe fournie avec le système. Voir la documentation
relative à l'installation et à la configuration du système d'exploitation si vous
installez celui-ci pour la première fois. Veillez à installer le système
d'exploitation avant tout élément matériel ou logiciel acheté séparément.
Systèmes d'exploitation pris en charge
• Microsoft Small Business Server 2011, éditions Standard et Essential
• Microsoft Windows Server 2008 R2 SP1, éditions Web, Standard,
Foundation et Enterprise (x64)
• Microsoft Windows
Server 2008 R2, éditions Web, Standard,
Foundation et Enterprise (x64)
• Microsoft Windows Server 2008 SP2, éditions Web, Standard et
Enterprise (x86)
• Microsoft Windows Server 2008 SP2, éditions Web, Standard et
Enterprise (x64)