Dell PowerConnect W-IAP175P User manual

Odie Cavazos, Technical Marketing
Colin King, Network Engineering
Valerie Padilla, Network Engineering
Dell Networking Mobility Starter Kit
Quick Setup Guide

Dell Networking Mobility Starter Kit – Quick Setup Guide
ii
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
This document is for informational purposes only and may contain typographical errors and
technical inaccuracies. The content is provided as is, without express or implied warranties of any
kind.
© 2012 Dell Inc. All rights reserved. Dell and its affiliates cannot be responsible for errors or omissions
in typography or photography. Dell, the Dell logo, and PowerEdge are trademarks of Dell Inc. Intel and
Xeon are registered trademarks of Intel Corporation in the U.S. and other countries. Microsoft,
Windows, and Windows Server are either trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries. Other trademarks and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Dell disclaims
proprietary interest in the marks and names of others.
August 2012| Rev. 1.0

Dell Networking Mobility Starter Kit – Quick Setup Guide
iii
Contents
Dell Networking Mobility Starter Kit.................................................................................4
What’s included in your Mobility Starter Kit......................................................................4
Purpose of this guide..................................................................................................4
Resources ...............................................................................................................4
Getting Started Network Topology ..................................................................................5
Getting Started with the Dell PowerConnect 5500 Series PoE Switch........................................5
Configuring the PowerConnect 5500 Series PoE Switch.........................................................6
Next steps and recommendations ..................................................................................9
Getting Started with Dell PowerConnect W-Instant Access Points.............................................9
Connecting your W-IAP105 Instant Access Points ................................................................9
Connect to the Provisioning Wi-Fi Network..................................................................... 10
Log in to the Dell PowerConnect W-Series Instant Access Point WebUI ................................... 10
Creating a Network.................................................................................................. 11
Next steps and recommendations ................................................................................ 14
Dell OpenManage Network Manager.............................................................................. 15
Downloading Dell OpenManage Network Manager ............................................................. 15
OMNM Download instructions:................................................................................... 16
OMNM Pre-Installation Checklist ................................................................................ 16

Dell Networking Mobility Starter Kit – Quick Setup Guide
4
Dell Networking Mobility Starter Kit
This guide will help you install and configure the Dell Networking Mobility Starter Kit. To ensure an
easy installation, please read through the entire guide and determine the configuration options that
will best suit your needs.
What’s included in your Mobility Starter Kit
•PowerConnect 5500 Series PoE Switch (1)
•PowerConnect W-Series W-IAP105 Instant Access Points (4)
•Dell OpenManage Network Manager (available online)
Purpose of this guide
This guide is to enable a network administrator to configure a basic network with the components of
the Mobility Starter Kit. The resulting network can be used as a starting point to enable access to any
resource connected to the network through the PowerConnect 5500 Series PoE switch. Access rules
and Security configuration is left to the network administrator after completing this Getting Started
Guide.
As an option, this guide also provides information to assist in the installation of Dell OpenManage
Network Manager (OMNM). This software is designed to help simplify management of your Dell network
environment through one unified console.
NOTE: Throughout the document, information or steps referring to OMNM will be optional.
Resources
•Dell Support manual site –
http://support.dell.com/manuals
•PowerConnect 5500 Series PoE manuals -
http://support.dell.com/support/edocs/network/pc5524p/
http://support.dell.com/support/edocs/network/pc5548p/
•PowerConnect W-Series Instant SW manuals-
http://support.dell.com/support/edocs/NETWORK/PC_WSer/Instant/
•Dell OpenManage Network Manager-
http://dell.com/NetworkManager

Dell Networking Mobility Starter Kit – Quick Setup Guide
5
Getting Started Network Topology
Getting Started with the Dell PowerConnect 5500 Series PoE Switch
This guide describes how to install and configure the PowerConnect 5500 Series PoE switch. The
outlined steps will guide you through the initial switch configuration to get the system up and running
as quickly as possible. We will use the switch’s automatic Setup Wizard to configure the following:
•Username and password
•Management switch IP address
•IP subnet mask
•Default gateway IP address
•SNMP Community String (optional)
For more information, see the Dell PowerConnect 5500 Series User Guide and Getting Started Guide at
support.dell.com/manuals.

Dell Networking Mobility Starter Kit – Quick Setup Guide
6
Figure 1 PowerConnect 5524P Switch Chassis
Configuring the PowerConnect 5500 Series PoE Switch
After the switch is installed on a flat surface or rack and connected to a power supply, we are ready to
begin the configuration.
1. Connect the switch to the terminal and boot the unit. The boot process runs for approximately
40-45 seconds. When the boot process completes, the following LEDs are lit, as shown in the
figure below.
•Power
•Status
•Fan (should be green)
NOTE: For more information on connecting the switch to a terminal, see “Connecting the
Switch to the Terminal” section in the Dell PowerConnect 5500 Series Getting Started Guide.
Figure 2 PowerConnect 5524P LEDs
2. Obtain the following information from the network administrator:
•Username and password for switch admin access
•The IP address assigned to the VLAN 1 interface through which the switch is to be
managed (by default, every external and internal port is a member of the VLAN 1)
•The IP subnet mask for the network
•The default gateway (next hop router) IP address for configuring the default route
•SNMP Community String and SNMP Management System IP address (optional)

Dell Networking Mobility Starter Kit – Quick Setup Guide
7
3. The Setup Wizard is run automatically .The Setup Wizard displays the following information:
Welcome to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration
and gets you up and running easily and quickly. You can skip the
Setup Wizard and enter CLI mode to manually configure the switch.
The system will prompt you with a default answer; by pressing Enter,
you accept the default value.
You must respond to the next question to run the Setup Wizard within
60 seconds, otherwise the system will continue with normal operation
using the default system configuration.
Would you like to enter the Setup Wizard (you must answer this
question within 60 seconds)? (Y/N)
4. Enter [Y] to run the wizard.
After entering [Y] the wizard provides interactive guidance through the initial switch
configuration. The following information is displayed:
You can exit the Setup Wizard at any time by entering [ctrl+Z].
The system is not set up for SNMP management by default.
If you enter [N] or if you do not respond within 60 seconds, the Setup Wizard automatically
exits and the CLI console prompt is displayed.
To manage the switch using SNMP (optional, required for OMNM) you can:
•Setup the initial SNMP version 2 account now.
•Return later and setup the SNMP version account.
For more information on setting up an SNMP version 2 account, see the Dell PowerConnect 5500
Series User Guide and Getting Started Guide at support.dell.com/manuals.
Would you like to set up the SNMP management interface now? [Y/N]
NOTE: If you are not setting up OMNM at this time and cannot obtain the SNMP information
in steps 6 and 7, enter [N] to skip to step 8. It is recommended to setup SNMP within this Setup
Wizard if you intend on using OMNM.
5. Enter [N] to skip to Step 8 or enter [Y] to continue the Setup Wizard. If you enter [Y] the
following information is displayed:
To set up the SNMP management account you must specify the management
system IP address and the "community string" or password that the
particular management system uses to access the switch. The wizard
automatically assigns the highest access level [Privilege Level 15] to
this account.
You can use Dell Network Manager or other management interfaces to
change this setting later and to add additional management system
later. For more information on adding management systems, see the user
documentation.

Dell Networking Mobility Starter Kit – Quick Setup Guide
8
To add a management station:
Please enter the SNMP community string to be used:
6. Enter the SNMP community string. You can use the default name "public"
Please enter the IP address of the Management System (A.B.C.D) or
wildcard (0.0.0.0) to manage from any Management Station: [0.0.0.0].
7. Enter the SNMP Management System IP.
8. Set up user account privilege level, as follows:
The following information is displayed:
Now we need to set up your initial privilege (Level 15) user account.
This account is used to login to the CLI and Web interface. You may set
up other accounts and change privilege levels later. For more
information on setting up user accounts and changing privilege levels,
see the user documentation.
To set up a user account:
Enter the user name:
Please enter the user password:
Please reenter the user password:
9. Enter the following:
•User name, for example "admin"
•Password and password confirmation.
10. Press Enter.
The following information is displayed:
Next, an IP address is setup. The IP address is defined on the default
VLAN (VLAN #1). This is the IP address you use to access the Telnet,
Web interface, or SNMP interface for the switch.
To set up an IP address:
Please enter the IP address of the device (A.B.C.D):
Please enter the IP subnet mask (A.B.C.D or nn):
11. Enter the management IP address and IP subnet mask, for example 192.168.2.100 as the IP
address, and 255.255.255.0 as the IP subnet mask.
12. Press Enter.
The following information is displayed:
Finally, set up the default gateway.
Please enter the IP address of the gateway from which this network is
reachable (e.g. 192.168.2.1). Default gateway (A.B.C.D):[0.0.0.0]

Dell Networking Mobility Starter Kit – Quick Setup Guide
9
13. Enter the default gateway and press enter. The following message is displayed (example):
This is the configuration information that has been collected:
SNMP Interface = "Dell Network Manager"@192.168.2.10
User Account setup = admin
Password = **********
Management IP address = 192.168.2.100
255.255.255.0
Default Gateway = 192.168.2.1
If the information is correct, please select (Y) to save the
configuration and copy to the start-up configuration file. If the
information is incorrect, select (N) to discard configuration and
restart the wizard: [Y/N]
14. Verify that the information is correct and select [Y] to save the configuration.
15. Continue managing the switch either through the console or Telnet, using the CLI or the web
GUI.
Next steps and recommendations
Before connecting the Instant Access Points to the 5500 Series PoE switch, ensure that a DHCP Server is
available and enabled on your network. Connect your DHCP Server to one of the ports on the
PowerConnect 5500 Series PoE switch. In some cases, the DHCP Server will be a function of your
internet provider. For the Dell Networking Mobility Starter Kit example, we are using the DHCP Server
from our internet router. Ensure that the DHCP service is disabled on the PowerConnect 5500 Series
PoE switch if you have another DHCP server on your network.
Getting Started with Dell PowerConnect W-Instant Access Points
The following information will assist you to quickly connect and configure Dell PowerConnect W-Series
Instant Access Point (IAP). After following the simple steps in this section, you’ll have a basic wireless
network that will let users access any resource on the subnet used in this Getting Started Guide.
For physical installation information and an overview of the W-105IAP hardware, see the Installation
Guide that’s included with the IAP.
For detailed configuration information, see the Dell PowerConnect W-Series Instant Access Point User
Guide.
Connecting your W-IAP105 Instant Access Points
After setting up your PowerConnect 5500 Series PoE switch, you are ready to connect the IAPs.
1. Using standard Cat5 Ethernet cable, connect the ENET port of the W-105IAP to the 5500 Series
PoE switch. All IAPs may be connected at this time, or just a single IAP.
2. The IAPs will boot, obtaining an IP address from the DHCP server you setup in the previous
section. All LEDs will be lit when the boot process completes.
NOTE: While in the provisioning state, access to the network is open to anyone that can connect to
the provisioning SSID. Ensure you complete the steps below in a prompt manner to secure the network.

Dell Networking Mobility Starter Kit – Quick Setup Guide
10
Connect to the Provisioning Wi-Fi Network
PowerConnect W-Series IAPs will be setup by accessing the WLAN through a SSID named “instant”.
3. On a PC with WLAN enabled, connect to the instant SSID as shown in Figure 3. Click the
Connect button
Figure 3 Connecting to provisioning network with Windows 7
Log in to the Dell PowerConnect W-Series Instant Access Point WebUI
4. Open a web browser and navigate to instant.dell-pcw.com to access the Dell Virtual Controller
login screen. If you enter any other URL, you are redirected to the same Dell Virtual Controller
login screen.
NOTE: Users may see a warning stating that there is a problem with a security certificate.
This is expected. Proceed to the login by clicking on the link to continue to the website.
5. In the login screen, as shown in Figure 4, enter the following credentials:
a. Username: admin
b. Password: admin
Figure 4 Virtual Controller Login