DeLonghi ETAM29.62X User manual

De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com 5713228941/10.15

ETAM29.62X
BEAN TO CUP ESPRESSO
AND CAPPUCCINO
MACHINE
Instruction for Use

2
EN
page 6
B
C
C5
C1 C3 C4*
B2 B3 B4
C2
B1 B5
B6B7B8B9B10B11
A16
A1
A
A4
A19
A5
A6
A2
B
A23
A11
A12
A3
A13 A14
A20
A15
A21
A22
A18
A10
C
A
P
P
U
C
C
I
N
O
H
O
T
M
I
L
K
A8
A7
A9
A17

3
B
C
C5
C1 C3 C4*
B2 B3 B4
C2
B1 B5
B6B7B8B9B10B11
A16
A1
A
A4
A19
A5
A6
A2
B
A23
A11
A12
A3
A13 A14
A20
A15
A21
A22
A18
A10
C
A
P
P
U
C
C
I
N
O
H
O
T
M
I
L
K
A8
A7
A9
A17

4
5
1
9
13
4
10
14
2
7
3
8
12
6
11
HOT MILK
15 16
29
25 26
22
18
30
27
23
31
28
24
2017 19
21 22 23
PUSH
PUSH

5
5
1
9
13
4
10
14
2
7
3
8
12
6
11
HOT MILK
15 16
29
25 26
22
18
30
27
23
31
28
24
2017 19
21 22 23
PUSH
PUSH

6
CONTENTS
1. FUNDAMENTAL SAFETY WARNINGS.............7
2. SAFETY WARNINGS ...................................8
2.1 Symbols used in this Instruction for Use........8
2.2 Designated use..............................................8
2.3 Instruction for Use.........................................8
3. INTRODUCTION..........................................8
3.1 Letters in brackets.........................................8
3.2 Troubleshooting and repairs..........................8
4. DESCRIPTION.............................................9
4.1 Description of the appliance .........................9
4.2 Description of the touch screen.....................9
4.3 Description of the accessories........................9
5. BEFORE USE...............................................9
5.1 Checking the appliance.................................9
5.2 Installing the appliance.................................9
5.3 Connecting the appliance..............................9
5.4 Setting up the appliance...............................9
6. TURNING THE APPLIANCE ON.................... 10
7. TURNING THE APPLIANCE OFF .................. 10
8. MENU SETTINGS ...................................... 10
8.1 Rinsing........................................................10
8.2 Descaling ....................................................11
8.3 Install lter..................................................11
8.4 Replacing the lter (if installed)..................11
8.5 Adjust time .................................................11
8.6 Auto-start ...................................................11
8.7 Auto-o (standby) ......................................11
8.8 Energy saving..............................................11
8.9 Setting the temperature .............................12
8.10 Setting water hardness ...............................12
8.11 Setting the language ..................................12
8.12 Beep............................................................12
8.13 Default values (reset)..................................12
8.14 Statistics function........................................12
9. MAKING COFFEE....................................... 12
9.1 Selecting the coee taste............................12
9.2 Selecting the quantity of coee in the cup..12
9.3 Customising the“my coee”quantity..........13
9.4 Adjusting the coee mill.............................13
9.5 Tips for a hotter coee.................................13
9.6 Making coee using coee beans ...............13
9.7 Making coee using pre-ground coee.......13
9.8 Making DOPPIO+ coee using coee beans ...
..................................................................14
9.9 Customising the DOPPIO+ coee quantity..14
9.10 Making LONG coee using coee beans......14
9.11 Making LONG coee using pre-ground coee .
..................................................................14
9.12 Customising the LONG coee quantity ........14
10. MAKING CAPPUCCINO AND HOT MILK
FROTHED .............................................. 14
10.1 Making hot milk (not frothed).....................15
10.2 Cleaning the cappuccino maker after use....15
11. DELIVERING HOT WATER .......................... 15
11.1 Changing the quantity of water delivered
automatically..............................................15
12. CLEANING................................................ 15
12.1 Cleaning the machine .................................15
12.2 Cleaning the machine’s internal circuit........16
12.3 Cleaning the coee grounds container........16
12.4 Cleaning the drip tray and condensate tray.16
12.5 Cleaning the inside of the coee machine...16
12.6 Cleaning the water tank..............................16
12.7 Cleaning the coee spouts ..........................16
12.8 Cleaning the pre-ground coee funnel .......16
12.9 Cleaning the infuser....................................16
13. DESCALING.............................................. 17
14. SETTING WATER HARDNESS...................... 18
14.1 Measuring water hardness..........................18
14.2 Setting water hardness ...............................18
15. WATER SOFTENER FILTER *CERTAIN MODELS
ONLY...................................................... 18
15.1 Installing the lter ......................................18
15.2 Replacing the lter......................................19
15.3 Removing the lter .....................................19
16. TECHNICAL DATA...................................... 19
17. DISPOSING OF THE APPLIANCE ................. 19
18. DISPLAYED MESSAGES.............................. 20
19. TROUBLESHOOTING ................................. 21
20. ELECTRICAL CONNECTION UK ONLY......... 22
1. FUNDAMENTAL SAFETY WARNINGS
• Appliances can be used by persons with reduced physical, sensory or mental capa-
bilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
• Never clean by immersing the appliance in water.
• This is an household appliance only. It is not intended to be used in: sta kitchen
areas in shops, oces and other working environments; farm houses; by clients in
hotels, motels and other residential type environments; bed and breakfast type
environments.
• If the plug or cord is damaged, it must be replaced by Customer Services only to avoid
all risk.
FOR EUROPEAN MARKETS ONLY:
• Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
• This appliance shall not be used by children. Keep the appliance and its cord out of
reach of children.
• Appliances can be used by persons with reduced physical, sensory or mental capa-
bilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).

7
9.9 Customising the DOPPIO+ coee quantity..14
9.10 Making LONG coee using coee beans......14
9.11 Making LONG coee using pre-ground coee .
..................................................................14
9.12 Customising the LONG coee quantity ........14
10. MAKING CAPPUCCINO AND HOT MILK
FROTHED .............................................. 14
10.1 Making hot milk (not frothed).....................15
10.2 Cleaning the cappuccino maker after use....15
11. DELIVERING HOT WATER .......................... 15
11.1 Changing the quantity of water delivered
automatically..............................................15
12. CLEANING................................................ 15
12.1 Cleaning the machine .................................15
12.2 Cleaning the machine’s internal circuit........16
12.3 Cleaning the coee grounds container........16
12.4 Cleaning the drip tray and condensate tray.16
12.5 Cleaning the inside of the coee machine...16
12.6 Cleaning the water tank..............................16
12.7 Cleaning the coee spouts ..........................16
12.8 Cleaning the pre-ground coee funnel .......16
12.9 Cleaning the infuser....................................16
13. DESCALING.............................................. 17
14. SETTING WATER HARDNESS...................... 18
14.1 Measuring water hardness..........................18
14.2 Setting water hardness ...............................18
15. WATER SOFTENER FILTER *CERTAIN MODELS
ONLY...................................................... 18
15.1 Installing the lter ......................................18
15.2 Replacing the lter......................................19
15.3 Removing the lter .....................................19
16. TECHNICAL DATA...................................... 19
17. DISPOSING OF THE APPLIANCE ................. 19
18. DISPLAYED MESSAGES.............................. 20
19. TROUBLESHOOTING ................................. 21
20. ELECTRICAL CONNECTION UK ONLY......... 22
1. FUNDAMENTAL SAFETY WARNINGS
• Appliances can be used by persons with reduced physical, sensory or mental capa-
bilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
• Never clean by immersing the appliance in water.
• This is an household appliance only. It is not intended to be used in: sta kitchen
areas in shops, oces and other working environments; farm houses; by clients in
hotels, motels and other residential type environments; bed and breakfast type
environments.
• If the plug or cord is damaged, it must be replaced by Customer Services only to avoid
all risk.
FOR EUROPEAN MARKETS ONLY:
• Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
• This appliance shall not be used by children. Keep the appliance and its cord out of
reach of children.
• Appliances can be used by persons with reduced physical, sensory or mental capa-
bilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).

8
4. DESCRIPTION
4.1 Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Pre-ground coee funnel lid
A3. Beans container
A4. Pre-ground coee funnel
A5. button: turns the appliance on and o (standby)
A6. Cup shelf
A7. Cappuccino maker selection ring
A8. Cappuccino maker
A9. Cappuccino maker nozzle
A10. Coee spouts (adjustable height)
A11. Condensate tray
A12. Cup tray
A13. Drip tray water level indicator
A14. Drip tray
A15. Coee grounds container
A16. Main switch (ON/OFF)
A17. Power cord
A18. Infuser door
A19. Infuser
A20. Water tank
A21. Water softener lter housing
A22. Water tank lid
A23. Grinding adjustment dial
4.2 Description of the touch screen
(page 2 - B )
A number of icons on the touch screen have a double function. This
is indicated in brackets in the description.
B1. OK icon (When in the settings menu, press to conrm the
selection)
B2. icon: to access or exit the settings menu
B3. Display
B4. icon: to select the coee quantity (When in the set-
tings menu, press to scroll through the menu)
B5. aroma selection icon: to select the coee taste
(When in the settings menu, press to scroll through the
menu)
B6. icon: to make 2 cups of coee with the settings
displayed
B7. icon: to make 1 cup of coee with the settings
displayed
B8. icon: to make one LONG coee
B9. icon: to make one DOPPIO+ coee
B10. icon: to deliver hot water
B11. icon to deliver steam
2. SAFETY WARNINGS
2.1 Symbols used in this Instruction for Use
Important warnings are identied by these symbols. It is vital to
respect these warnings.
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Please note:
This symbol identies important advice or information for the
user.
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore follow these safety warnings:
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• Unplug directly from the plug only. Never pull the cord as
you could damage it.
• To disconnect the appliance completely you must unplug it
from the mains socket.
• If the appliance is faulty, do not attempt to repair.
Turn it o, unplug from the mains socket and contact Cus-
tomer Services.
• Before cleaning the appliance, turn it o, unplug from the
mains socket and allow to cool.
Important:
Keep all packaging (plastic bags, polystyrene foam) away from
children.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf (A6) could
become very hot.
2.2 Designated use
This appliance is designed and made to prepare coee and heat
drinks.
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
2.3 Instruction for Use
Read this Instruction for Use carefully before using the appli-
ance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Please note:
Keep this Instruction for Use. If the appliance is passed to other
persons, they must also be provided with this Instruction for
Use.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuc-
cino machine.
We hope you enjoy using your new appliance. Take a few min-
utes to read this Instruction for Use. This will avoid all risks and
damage to the appliance.
3.1 Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2 Troubleshooting and repairs
In the event of problems, rst try and resolve them by reading
the information given in sections“18. Displayed messages”and
“19. Troubleshooting”.
If this does not resolve the problem or you require further in-
formation, you should consult Customer Services by calling the
number given on the annexed“Customer Service”sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certicate provided with the machine.

9
4. DESCRIPTION
4.1 Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Pre-ground coee funnel lid
A3. Beans container
A4. Pre-ground coee funnel
A5. button: turns the appliance on and o (standby)
A6. Cup shelf
A7. Cappuccino maker selection ring
A8. Cappuccino maker
A9. Cappuccino maker nozzle
A10. Coee spouts (adjustable height)
A11. Condensate tray
A12. Cup tray
A13. Drip tray water level indicator
A14. Drip tray
A15. Coee grounds container
A16. Main switch (ON/OFF)
A17. Power cord
A18. Infuser door
A19. Infuser
A20. Water tank
A21. Water softener lter housing
A22. Water tank lid
A23. Grinding adjustment dial
4.2 Description of the touch screen
(page 2 - B )
A number of icons on the touch screen have a double function. This
is indicated in brackets in the description.
B1. OK icon (When in the settings menu, press to conrm the
selection)
B2. icon: to access or exit the settings menu
B3. Display
B4. icon: to select the coee quantity (When in the set-
tings menu, press to scroll through the menu)
B5. aroma selection icon: to select the coee taste
(When in the settings menu, press to scroll through the
menu)
B6. icon: to make 2 cups of coee with the settings
displayed
B7. icon: to make 1 cup of coee with the settings
displayed
B8. icon: to make one LONG coee
B9. icon: to make one DOPPIO+ coee
B10. icon: to deliver hot water
B11. icon to deliver steam
4.3 Description of the accessories
(page 2 - C )
C1. “Total Hardness Test”indicator paper
C2. Pre-ground coee measure
C3. Descaler
C4. Water softener lter (*certain models only)
C5. Cleaning brush
5. BEFORE USE
5.1 Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact De’Longhi
Customer Services.
5.2 Installing the appliance
Important!
When you install the appliance, you should respect the follow-
ing safety warnings:
• The appliance gives o heat. After positioning the appli-
ance on the worktop, leave a space of at least 3 cm be-
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coee maker.
• Water penetrating the coee machine could cause
damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an eciently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
professional.
5.4 Setting up the appliance
Please note :
• Coee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
Any other use is considered improper and thus dangerous. The
manufacturer is not liable for damage deriving from improper
use of the appliance.
2.3 Instruction for Use
Read this Instruction for Use carefully before using the appli-
ance. Failure to follow this Instruction for Use may result in
burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect this Instruction for Use.
Please note:
Keep this Instruction for Use. If the appliance is passed to other
persons, they must also be provided with this Instruction for
Use.
3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuc-
cino machine.
We hope you enjoy using your new appliance. Take a few min-
utes to read this Instruction for Use. This will avoid all risks and
damage to the appliance.
3.1 Letters in brackets
The letters in brackets refer to the legend in the description of
the appliance on pages 2-3.
3.2 Troubleshooting and repairs
In the event of problems, rst try and resolve them by reading
the information given in sections“18. Displayed messages”and
“19. Troubleshooting”.
If this does not resolve the problem or you require further in-
formation, you should consult Customer Services by calling the
number given on the annexed“Customer Service”sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee. If repairs are required, contact
De’Longhi Customer Services only. The addresses are given in
the guarantee certicate provided with the machine.

10
4. Press the OK icon: after a few seconds, hot water is delivered
from the coee spouts to clean and heat the appliance’s in-
ternal circuit.
Please note!
• To stop delivery at any time, press any icon.
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use.
8.2 Descaling
For instructions on descaling, see section“13. Descaling”.
8.3 Install lter
For instructions on how to install the lter, see section “15.
Water softener lter (*certain models only)”.
8.4 Replacing the lter (if installed)
For instructions on how to replace the lter, see section “15.2
Replacing the lter”.
8.5 Adjust time
To adjust the time on the display (B3), proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Adjust time”is
displayed.
3. Press the OK icon (B1) (g. 4). The hours ash on the
display.
4. Press or to change the hour.
5. Press the OK icon to conrm.The minutes ash.
6. Press or to change the minutes.
7. Press the OK icon to conrm.
This sets the time. Press the icon to exit the menu.
8.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Auto-start”
appears on the display (B3).
3. Press the OK icon (B1) (g. 4).“Enable?”is displayed.
4. Press the OK icon to conrm.
5. Press or to choose the hour.
6. Press the OK icon to conrm.
fee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the instructions in section “14. Setting water
hardness”.
1. Connect the appliance to the mains electricity supply and
make sure the main switch (A16) at the back of the appli-
ance is pressed down (g. 1).
2. Remove the water tank (A20) (g. 2), open the lid (A22) (g.
3), ll to the MAX line with fresh water, replace the lid and
put the tank back in the appliance.
You must rst choose the language by moving backwards and
forwards with the (B4) or (B5) icon, or waiting
until the languages scroll through on the display (B3) at inter-
vals of about 3 seconds:
3. When “English” appears, press and hold the OK icon (B1)
(g. 4) for a few seconds until “English set” appears on the
display.
Follow the instructions indicated on the appliance display:
4. “HOT WATER, Press OK”: place a container with a minimum
capacity of 100 ml under the cappuccino maker (A8) (g. 5).
5. Press the OK icon to conrm (g. 4). The appliance delivers
water from the spout then goes o automatically.
The coee machine is now ready for normal use.
Please note :
• The rst time you use the appliance, you need to make 4-5
cups of coee before the appliance starts to give satisfac-
tory results.
• To enjoy your coee even more and improve the perfor-
mance of your appliance, we recommend installing a
water softener lter (C4) as described in section“15. Water
softener lter (*certain models only)”. If your model is not
provided with a lter, you can request one from De’Longhi
Customer Services.
6. TURNING THE APPLIANCE ON
Please note!
• Before turning the appliance on, make sure the main
switch (A16) is pressed (g. 1).
• Each time the appliance is turned on, it performs an auto-
matic preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
(A10) and is collected in the drip tray (A14). Avoid contact with
splashes of water.
• To turn the appliance on, press the button (A5) (g.
6). The message “Heating up Please wait” appears on the
display (B3).
When heating is complete, the message changes to“Rinsing”. As
well as heating the boiler, this also heats the internal circuits by
circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coee appears.
7. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A10). Avoid contact with splashes of water.
• To turn the appliance o, press the button (A10) (g.
6).
• The message“Turning o Please wait” appears on the dis-
play (B3), then the appliance performs a rinse cycle and
goes o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button
(g. 6);
• Press the main switch (A16) on the side of the appliance
(g. 1).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
8.1 Rinsing
Use this function to deliver hot water from the coee spouts
(A10) to clean and heat the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coee spout.
To enable the function, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Rinsing” ap-
pears on the display (B3).
3. Press the OK icon (B1) (g. 4) to conrm, “Conrm?” is
displayed.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.

11
4. Press the OK icon: after a few seconds, hot water is delivered
from the coee spouts to clean and heat the appliance’s in-
ternal circuit.
Please note!
• To stop delivery at any time, press any icon.
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use.
8.2 Descaling
For instructions on descaling, see section“13. Descaling”.
8.3 Install lter
For instructions on how to install the lter, see section “15.
Water softener lter (*certain models only)”.
8.4 Replacing the lter (if installed)
For instructions on how to replace the lter, see section “15.2
Replacing the lter”.
8.5 Adjust time
To adjust the time on the display (B3), proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Adjust time”is
displayed.
3. Press the OK icon (B1) (g. 4). The hours ash on the
display.
4. Press or to change the hour.
5. Press the OK icon to conrm.The minutes ash.
6. Press or to change the minutes.
7. Press the OK icon to conrm.
This sets the time. Press the icon to exit the menu.
8.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Auto-start”
appears on the display (B3).
3. Press the OK icon (B1) (g. 4).“Enable?”is displayed.
4. Press the OK icon to conrm.
5. Press or to choose the hour.
6. Press the OK icon to conrm.
7. Press or to change the minutes.
8. Press the OK icon to conrm.
9. Then press the icon to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu.
2. Press the OK icon.“Disable?”is displayed.
3. Press the OK icon to conrm.
The symbol is no longer displayed .
8.7 Auto-o (standby)
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Auto-o” ap-
pears on the display (B3).
3. Press the OK icon (B1) (g. 4).
4. Press or until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed.
5. Press the OK icon to conrm.
6. Then press the icon to exit the menu.
Auto-o is now programmed.
8.8 Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Energy Saving”
appears on the display (B3).
3. Press the OK icon (B1) (g. 4). “Disable?” is displayed (or
“Enable?”if the function has been disabled).
4. Press the OK icon to disable (or enable) energy saving
mode.
5. Then press the icon to exit the menu.
When the function is active, if the machine is not used for some
time,“Energy saving”is displayed.
Please note!
• When in energy saving mode, a few seconds may elapse
before the rst coee is delivered as the appliance must
heat up again.
• To prepare any beverage, press any icon to exit energy sav-
ing, then press the icon corresponding to the beverage you
want to make.
• To turn the appliance on, press the button (A5) (g.
6). The message “Heating up Please wait” appears on the
display (B3).
When heating is complete, the message changes to“Rinsing”. As
well as heating the boiler, this also heats the internal circuits by
circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coee appears.
7. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A10). Avoid contact with splashes of water.
• To turn the appliance o, press the button (A10) (g.
6).
• The message“Turning o Please wait” appears on the dis-
play (B3), then the appliance performs a rinse cycle and
goes o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button
(g. 6);
• Press the main switch (A16) on the side of the appliance
(g. 1).
Important!
Never press the main switch while the appliance is on.
8. MENU SETTINGS
8.1 Rinsing
Use this function to deliver hot water from the coee spouts
(A10) to clean and heat the appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coee spout.
To enable the function, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Rinsing” ap-
pears on the display (B3).
3. Press the OK icon (B1) (g. 4) to conrm, “Conrm?” is
displayed.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.

12
9.3 Customising the “my coee”quantity
The appliance is set by default to automatically deliver about
30ml of“my coee”. To modify this quantity, proceed as follows:
1. Place a cup under the coee spouts (A10) (g. 10).
2. Press the icon (B4) (g. 9) until “MY COFFEE” is
displayed.
3. Press and hold the icon (B7) until the message“1 MY
COFFEE Program quantity”appears on the display (B3) and
coee delivery begins. Release the icon.
4. As soon as the coee in the cup reaches the required level,
press the icon again.
The quantity of coee in the cup has now been programmed.
9.4 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A23) (g. 11).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coee, turn
one click anticlockwise towards 1 (do
not turn more than one click at a time
otherwise the coee could be delivered
a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.5 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle by selecting the “Rinse” function in
the settings menu (see section“8.1 Rinsing”).
• warm the cups with hot water (see section “11. Delivering
hot water”).
• increase the coee temperature in the settings menu (see
section“8.9 Setting the temperature”).
9.6 Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
8.9 Setting the temperature
To modify the temperature of the water used to make the coee,
proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Set tempera-
ture”appears on the display (B3).
3. Press the OK icon (B1) (g. 4).
4. Press or until the required temperature is
displayed (●=low; ●●●●=maximum).
5. Press the OK icon to conrm.
6. Then press the icon to exit the menu.
8.10 Setting water hardness
For instructions on setting water hardness, see section“14. Set-
ting water hardness”.
8.11 Setting the language
To modify the language of the display (B3), proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Set language”
is displayed.
3. Press the OK icon (B1) (g. 4).
4. Press or until the required language is
displayed.
5. Press the OK icon to conrm.
6. A message conrming the language installed is displayed.
7. Then press the icon to exit the menu.
8.12 Beep
This enables or disables the beep emitted by the machine each
time an icon/button is pressed, the drip tray is inserted/removed
or the door is opened/closed.To disable or enable the beep, pro-
ceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Beep”appears
on the display (B3).
3. Press the OK icon (g. 4). “Disable?” is displayed (or “Ena-
ble?”if the function has been disabled).
4. Press the OK icon to enable or disable the beep.
5. Then press the icon to exit the menu.
8.13 Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
To reset the default values, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until“Default val-
ues”appears on the display (B3).
3. Press the OK icon (B1) (g. 4).
4. The message“Conrm?”is displayed.
5. Press the OK icon to conrm and exit.
8.14 Statistics function
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Statistics”
appears on the display (B3).
3. Press the OK icon (B1) (g. 4).
4. By pressing or you can check:
- how many coees have been made;
- the total number of litres of water delivered;
- how many times the machine has been descaled;
- how many times the water softener lter has been
replaced.
5. Press the icon twice to exit the menu.
9. MAKING COFFEE
9.1 Selecting the coee taste
The appliance is set by default to make coee with a standard
taste.You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the icon (B5) (g. 8) repeatedly
until the required taste appears on the display (B3).
9.2 Selecting the quantity of coee in the cup
The appliance is set by default to make a standard quantity of
coee. To select the quantity of coee, press the icon
(B4) (g. 9) until the message corresponding to the required
quantity of coee appears on the display (B3):
Coee selected Quantità in tazza (ml)
MY COFFEE Programmable:
from ≃20 to ≃180
SHORT ≃40
STANDARD ≃60
LONG ≃90
EXTRA LONG ≃120

13
9.3 Customising the “my coee”quantity
The appliance is set by default to automatically deliver about
30ml of“my coee”. To modify this quantity, proceed as follows:
1. Place a cup under the coee spouts (A10) (g. 10).
2. Press the icon (B4) (g. 9) until “MY COFFEE” is
displayed.
3. Press and hold the icon (B7) until the message“1 MY
COFFEE Program quantity”appears on the display (B3) and
coee delivery begins. Release the icon.
4. As soon as the coee in the cup reaches the required level,
press the icon again.
The quantity of coee in the cup has now been programmed.
9.4 Adjusting the coee mill
The coee mill is set by default to prepare coee correctly and
should not require regulating initially.
However, if after making the rst few coees you nd that the
coee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial (A23) (g. 11).
Please note!
The grinding adjustment dial must only be turned when the
coee mill is in operation.
If the coee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coee, turn
one click anticlockwise towards 1 (do
not turn more than one click at a time
otherwise the coee could be delivered
a drop at a time).
These adjustments will only be evident after at least 2 cups of
coee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
9.5 Tips for a hotter coee
For hotter coee, you should:
• perform a rinse cycle by selecting the “Rinse” function in
the settings menu (see section“8.1 Rinsing”).
• warm the cups with hot water (see section “11. Delivering
hot water”).
• increase the coee temperature in the settings menu (see
section“8.9 Setting the temperature”).
9.6 Making coee using coee beans
Important!
Do not use caramelised or candied coee beans as they could
stick to the coee mill and make it unusable.
1. Fill the container (A3) (g. 12) with coee beans.
2. Place under the coee spouts (A10):
- 1 cup, if you want to make 1 coee (g. 10);
- 2 cups, if you want 2 coees (g. 13).
3. Lower the spouts as near as possible to the cup. This makes
a creamier coee (g. 14).
4. Press the icon corresponding to the number of coees re-
quired (B7 - 1 cup or B6 -2 cups ).
5. Preparation begins.The amount of coee selected appears
on the display together with a progress bar which gradual-
ly lls as preparation progresses.
Please note:
• While the machine is making coee, delivery can be inter-
rupted at any moment by pressing any icon.
• At the end of delivery, to increase the quantity of coee in
the cup, within 3 seconds just press one of the coee icons (
or ).
Once the coee has been made, the appliance is ready to make
the next drink
Important!
• Various alarm messages could be displayed while using the
appliance (ll tank, empty grounds container, etc.). Their
meaning is explained in section“18. Displayed messages”.
• For hotter coee, see section“9.5Tips for a hotter coee”.
• If the coee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section “19.
Troubleshooting”.
9.7 Making coee using pre-ground coee
Important!
• Never place coee beans in the pre-ground coee funnel
(A4) as this could damage the appliance.
• Never add pre-ground coee when the machine is o or it
could spread through the inside of the machine and dirty
it.This could damage the appliance.
• Never use more than 1 level measure (C2) or it could dirty
the inside of the coee machine or block the funnel.
Please note!
When you use pre-ground coee, you can only make one cup of
coee at a time.
1. Press the icon (B4) repeatedly (B4) (g. 8) until“Pre-
ground”appears on the display (B3).
2. Open the pre-ground coee funnel lid (A2).
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coee.
4. Place a cup under the coee spouts (A10) (g. 10).
5. Press the 1 cup coee icon (B7).
3. Press the OK icon (B1) (g. 4).
4. The message“Conrm?”is displayed.
5. Press the OK icon to conrm and exit.
8.14 Statistics function
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) until “Statistics”
appears on the display (B3).
3. Press the OK icon (B1) (g. 4).
4. By pressing or you can check:
- how many coees have been made;
- the total number of litres of water delivered;
- how many times the machine has been descaled;
- how many times the water softener lter has been
replaced.
5. Press the icon twice to exit the menu.
9. MAKING COFFEE
9.1 Selecting the coee taste
The appliance is set by default to make coee with a standard
taste.You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the icon (B5) (g. 8) repeatedly
until the required taste appears on the display (B3).
9.2 Selecting the quantity of coee in the cup
The appliance is set by default to make a standard quantity of
coee. To select the quantity of coee, press the icon
(B4) (g. 9) until the message corresponding to the required
quantity of coee appears on the display (B3):
Coee selected Quantità in tazza (ml)
MY COFFEE Programmable:
from ≃20 to ≃180
SHORT ≃40
STANDARD ≃60
LONG ≃90
EXTRA LONG ≃120

14
7. After a few seconds, steam is delivered from the cappucci-
no maker, giving the milk a creamy frothy appearance and
making it more voluminous.
8. For a creamier froth, rotate the container with slow move-
ments in an upward direction. (You should not discharge
steam for more than 3 minutes at a time).
9. When the required temperature is obtained, interrupt
steam delivery by pressing the icon.
Danger of burns!
Stop steam delivery before removing the container with the
frothed milk to avoid burns caused by splashes of boiling milk.
10. Add the milk froth to the coee prepared previously. The
cappuccino is ready. Sweeten to taste and, if desired, sprin-
kle the froth with a little cocoa powder.
Please note!
If“Energy saving”is active, you may have to wait a few seconds
before steam is delivered.
10.1 Making hot milk (not frothed)
To make hot milk without froth, proceed as described in the
above section, but with the cappuccino maker selection ring
(A7) positioned upwards in the“HOT MILK”position.
10.2 Cleaning the cappuccino maker after use
Clean the cappuccino maker (A8) each time you use it to avoid
the build-up of milk residues or blockages.
Danger of burns!
When cleaning the cappuccino maker, a little hot water is deliv-
ered. Avoid contact with splashes of water.
1. Deliver a little water by pressing the con (B10). Press
the same icon again to stop the ow of hot water.
2. Wait a few minutes for the cappuccino maker to cool down.
Turn the cappuccino maker downwards to remove it (g.
17).
3. Move the cappuccino/hot milk ring upwards (g. 18).
4. Remove the nozzle downwards (A9) (g. 19).
5. Make sure the two holes shown by the arrow in g. 20 are
not blocked. If necessary, clean with a pin.
6. Replace the nozzle, move the selection ring downwards and
put the cappuccino maker back on the nozzle (g. 21), turn-
ing it clockwise and pushing it upwards until it is attached.
11. DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
6. Preparation begins. The amount of coee selected is dis-
played together with a progress bar which gradually lls as
preparation progresses.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before the rst coee is delivered.
9.8 Making DOPPIO+ coee using coee beans
Follow the instructions in section “9.6 Making coee using cof-
fee beans”to prepare the machine and press the icon (B9).
9.9 Customising the DOPPIO+ coee quantity
The appliance is set by default to deliver about 120 ml of DOP-
PIO+ coee.To modify these settings, proceed as follows:
1. Place a suciently large cup or glass under the coee
spouts (A10) (g. 10);
2. Press and hold the icon (B9) until“Program quanti-
ty”is displayed;
3. Release the icon. The appliance starts delivering
coee;
4. As soon as the coee in the cup reaches the required level,
press the icon again.
The quantity of coee in the cup has now been programmed.
Please note!
You can programme a minimum quantity of about 80ml.
You can programme a maximum quantity of about 160ml.
9.10 Making LONG coee using coee beans
Follow the instructions in section “9.6 Making coee using cof-
fee beans”to prepare the machine and press the icon (B8).
9.11 Making LONG coee using pre-ground coee
1. Follow the instructions in points 1, 2, 3 and 4 of section
“9.7 Making coee using pre-ground coee”, then press
the icon (B8).
2. The appliance starts making coee and displays a progress
bar. Halfway through preparation, the message “ADD pre-
ground coee, Press OK”appears.
3. Add one level measure (C2) of pre-ground coee and press
OK (B1) (g. 4).
4. Preparation resumes and the appliance displays a progress
bar which lls gradually as preparation proceeds.
9.12 Customising the LONG coee quantity
The appliance is set by default to automatically deliver about
200ml of LONG coee. To modify these settings, proceed as
follows:
1. Place a suciently large cup or glass under the coee
spouts (A10) (g. 10).
2. Press and hold the icon (B8) until“Program quantity”
is displayed.
3. Release the icon. The appliance starts delivering
coee;
4. As soon as the coee in the cup reaches the required level,
press the icon again.
The quantity of coee in the cup has now been programmed.
Please note!
If the programme uses pre-ground coee, the appliance will
prompt you to add a second level measure of coee.
10. MAKING CAPPUCCINO AND HOT MILK
FROTHED
Danger of burns!
During preparation steam is given o. Take care to avoid scalds.
1. When preparing cappuccino, make the coee in a large
cup.
2. Fill a container (preferably one with a handle to avoid
scalding) with about 100 grams of milk for each cappucci-
no. In choosing the size of the container, bear in mind that
the milk doubles or triples in volume.
Please note :
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C). To avoid milk
with poor froth or large bubbles, always clean the cappuc-
cino maker (A8) as described in the section“6. R e p l a c e
the nozzle, move the selection ring downwards and put
the cappuccino maker back on the nozzle (g. 21), turning
it clockwise and pushing it upwards until it is attached.”.
3. Make sure the cappuccino maker selection ring (A7) is posi-
tioned downwards in the“CAPPUCCINO”position (g. 15).
4. The cappuccino maker can be turned slightly outwards to
allow containers of any size to be used (g. 16).
5. Immerse the cappuccino maker in the milk container.
Never immerse the black ring.
6. Press the icon (B11).“STEAM”appears on the display
(B3).

15
7. After a few seconds, steam is delivered from the cappucci-
no maker, giving the milk a creamy frothy appearance and
making it more voluminous.
8. For a creamier froth, rotate the container with slow move-
ments in an upward direction. (You should not discharge
steam for more than 3 minutes at a time).
9. When the required temperature is obtained, interrupt
steam delivery by pressing the icon.
Danger of burns!
Stop steam delivery before removing the container with the
frothed milk to avoid burns caused by splashes of boiling milk.
10. Add the milk froth to the coee prepared previously. The
cappuccino is ready. Sweeten to taste and, if desired, sprin-
kle the froth with a little cocoa powder.
Please note!
If“Energy saving”is active, you may have to wait a few seconds
before steam is delivered.
10.1 Making hot milk (not frothed)
To make hot milk without froth, proceed as described in the
above section, but with the cappuccino maker selection ring
(A7) positioned upwards in the“HOT MILK”position.
10.2 Cleaning the cappuccino maker after use
Clean the cappuccino maker (A8) each time you use it to avoid
the build-up of milk residues or blockages.
Danger of burns!
When cleaning the cappuccino maker, a little hot water is deliv-
ered. Avoid contact with splashes of water.
1. Deliver a little water by pressing the con (B10). Press
the same icon again to stop the ow of hot water.
2. Wait a few minutes for the cappuccino maker to cool down.
Turn the cappuccino maker downwards to remove it (g.
17).
3. Move the cappuccino/hot milk ring upwards (g. 18).
4. Remove the nozzle downwards (A9) (g. 19).
5. Make sure the two holes shown by the arrow in g. 20 are
not blocked. If necessary, clean with a pin.
6. Replace the nozzle, move the selection ring downwards and
put the cappuccino maker back on the nozzle (g. 21), turn-
ing it clockwise and pushing it upwards until it is attached.
11. DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
Please note!
If “Energy Saving” mode is active, you may have to wait a few
seconds before hot water is delivered.
1. Place a container under the coee spouts (A10) (as close as
possible to avoid splashes).
2. Press the icon (B10). “HOT WATER” appears on the
display (B3), together with a progress bar which lls grad-
ually as preparation proceeds.
3. The machine delivers about 250 ml of hot water, then de-
livery stops automatically. To interrupt delivery of the hot
water manually, press the icon again.
11.1 Changing the quantity of water delivered
automatically
The machine is set by default to automatically deliver 250 ml of
hot water.To modify these quantities, proceed as follows:
1. Position a container under the coee spouts (A10) (g. 5).
2. Press and hold the icon (B10) again until“HOTWATER
Program Quantity” appears on the display (B3), then re-
lease the icon.
3. When the hot water in the cup reaches the required level,
press the icon again.
The machine is now reprogrammed with the new quantity.
12. CLEANING
12.1 Cleaning the machine
The following parts of the machine must be cleaned regularly:
- the appliance’s internal circuit;
- coee grounds container (A15);
- drip tray (A14) and condensate tray (A11);
- water tank (A20);
- coee spouts (A10);
- cappuccino maker (A8 -“6. Replace the nozzle,
move the selection ring downwards and put the cappucci-
no maker back on the nozzle (g. 21), turning it clockwise
and pushing it upwards until it is attached.”);
- pre-ground coee funnel (A4);
- infuser (A19), accessible after opening the infuser door
(A18);
Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the coee machine.With De’Longhi superautomatic coee
machines, you need not use chemical products to clean the
machine.
• None of the components can be washed in a dishwasher.
• Do not use metal objects to remove encrustations or coee
deposits as they could scratch metal or plastic surfaces.
9.12 Customising the LONG coee quantity
The appliance is set by default to automatically deliver about
200ml of LONG coee. To modify these settings, proceed as
follows:
1. Place a suciently large cup or glass under the coee
spouts (A10) (g. 10).
2. Press and hold the icon (B8) until“Program quantity”
is displayed.
3. Release the icon. The appliance starts delivering
coee;
4. As soon as the coee in the cup reaches the required level,
press the icon again.
The quantity of coee in the cup has now been programmed.
Please note!
If the programme uses pre-ground coee, the appliance will
prompt you to add a second level measure of coee.
10. MAKING CAPPUCCINO AND HOT MILK
FROTHED
Danger of burns!
During preparation steam is given o. Take care to avoid scalds.
1. When preparing cappuccino, make the coee in a large
cup.
2. Fill a container (preferably one with a handle to avoid
scalding) with about 100 grams of milk for each cappucci-
no. In choosing the size of the container, bear in mind that
the milk doubles or triples in volume.
Please note :
For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C). To avoid milk
with poor froth or large bubbles, always clean the cappuc-
cino maker (A8) as described in the section“6. R e p l a c e
the nozzle, move the selection ring downwards and put
the cappuccino maker back on the nozzle (g. 21), turning
it clockwise and pushing it upwards until it is attached.”.
3. Make sure the cappuccino maker selection ring (A7) is posi-
tioned downwards in the“CAPPUCCINO”position (g. 15).
4. The cappuccino maker can be turned slightly outwards to
allow containers of any size to be used (g. 16).
5. Immerse the cappuccino maker in the milk container.
Never immerse the black ring.
6. Press the icon (B11).“STEAM”appears on the display
(B3).

16
3. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (g. 28).
4. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID  NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
5. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door.
6. After cleaning, replace the infuser by sliding it onto the
internal support (g. 29), then push the PUSH symbol fully
in until it clicks into place.
Please note!
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in g. 30.
7. Once inserted, make sure the two coloured buttons have
snapped out (g. 31).
8. Close the infuser door.
13. DESCALING
Descale the machine when the message“descale”ashes on the
display (B3).
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer’s guarantee.
1. Turn the appliance on and wait until it is ready for use.
2. Press the icon (B2) to enter the menu (B2).
3. Press (B4) or (B5) (g. 7) until “Descale” is
displayed.
4. Select by pressing the OK icon (B1) (g. 4): the message
“Descaling Conrm?”is displayed.
5. Press the OK icon again to conrm. “EMPTY DRIP TRAY” is
displayed, alternating with“REMOVE FILTER”(if the lter is
present) and“Add descaler, Press OK”.
6. Empty the water tank (A20) completely and remove the
water softener lter (C4), if present. Empty the drip tray
(A14 - g. 22) and grounds container (A15), then put them
back in the appliance.
12.2 Cleaning the machine’s internal circuit
If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
• performing 2-3 rinse cycles by selecting the rinse function
(see section“8.1 Rinsing”);
• delivering hot water for a few seconds by pressing the
icon (B10).
Please note!
After cleaning, it is normal for the grounds container (A15) to
contain water.
12.3 Cleaning the coee grounds container
When “empty grounds container” appears on the display (B3),
the grounds container must be emptied and cleaned. The ap-
pliance cannot be used to make coee until you have cleaned
the grounds container (A15). Even if not full, the empty grounds
container message is displayed 72 hours after the rst coee has
been prepared. For the 72 hours to be calculated correctly, the
machine must never be turned o with the main switch.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray (A12) becomes hot. Wait for it to cool down be-
fore touching it and handle from the front only.
To clean (with the machine on):
• Remove the drip tray (A14) (g. 22), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
using the spatula on the brush (C5) provided.
• Check the condensate tray (A11) and empty if necessary
(g. 23).
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coees, the grounds container may ll
up more than expected and clog the machine.
12.4 Cleaning the drip tray and condensate tray
Important!
The drip tray (A14) is tted with a level indicator (red) (A13)
showing the level of water it contains (g. 24). Before the in-
dicator protrudes from the cup tray (A12), the drip tray must
be emptied and cleaned otherwise the water may overow the
edge and damage the appliance, the surface it rests on or the
surrounding area.
To remove the drip tray:
1. Remove the drip tray and the coee grounds container
(A15) (g. 22).
2. Empty the drip tray and grounds container and wash them.
3. Check the condensate tray (A11) and empty if necessary.
4. Replace the drip tray and grounds container.
12.5 Cleaning the inside of the coee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned o
(see section“7.Turning the appliance o”) and unplugged from
the mains power supply. Never immerse the coee machine in
water.
1. Check regularly (about once a month) that the inside of the
appliance (accessible after removing the drip tray (A14)
is not dirty. If necessary, remove coee deposits with the
brush (C5) supplied and a sponge.
2. Remove all the residues with a vacuum cleaner (g. 25).
12.6 Cleaning the water tank
1. Clean the water tank (A20) regularly (about once a month
and whenever you replace the water softener lter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid.
2. Remove the lter (if present) and rinse with running water.
3. Replace the lter (if provided), ll the tank with fresh
water and replace the tank.
4. (Models with water softener lter only) Deliver about
100ml of hot water to reactivate the lter.
12.7 Cleaning the coee spouts
1. Clean the coee spouts (A10) regularly with a sponge or
cloth (g. 26).
2. Check that the holes in the coee spouts are not blocked.
If necessary, remove coee deposits with a toothpick (g.
26).
12.8 Cleaning the pre-ground coee funnel
Check regularly (about once a month ) that the pre-ground
coee funnel (A4) is not blocked. If necessary, remove coee
deposits with the brush (C5) supplied.
12.9 Cleaning the infuser
The infuser (A19) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see section
“7. Turning the appliance o”).
2. Open the infuser door (A18) (g. 27) on the right side of
the appliance.

17
3. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (g. 28).
4. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID  NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
5. Use the brush (C5) to remove any coee residues left in the
infuser housing, visible through the infuser door.
6. After cleaning, replace the infuser by sliding it onto the
internal support (g. 29), then push the PUSH symbol fully
in until it clicks into place.
Please note!
If the infuser is dicult to insert, before insertion, adapt it to the
right size by pressing the two levers shown in g. 30.
7. Once inserted, make sure the two coloured buttons have
snapped out (g. 31).
8. Close the infuser door.
13. DESCALING
Descale the machine when the message“descale”ashes on the
display (B3).
Important!
• Before use, read the instructions and the labelling on the
descaler pack.
• You should use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may re-
sult in faults not covered by the manufacturer’s guarantee.
1. Turn the appliance on and wait until it is ready for use.
2. Press the icon (B2) to enter the menu (B2).
3. Press (B4) or (B5) (g. 7) until “Descale” is
displayed.
4. Select by pressing the OK icon (B1) (g. 4): the message
“Descaling Conrm?”is displayed.
5. Press the OK icon again to conrm. “EMPTY DRIP TRAY” is
displayed, alternating with“REMOVE FILTER”(if the lter is
present) and“Add descaler, Press OK”.
6. Empty the water tank (A20) completely and remove the
water softener lter (C4), if present. Empty the drip tray
(A14 - g. 22) and grounds container (A15), then put them
back in the appliance.
32
B
A
7. Pour the descaler (C3) into
the tank up to level A (cor-
responding to a 100 ml
pack) marked on the back
of the tank (g. 32), then
add a litre of water up to
level B (g. 32) and put
the water tank back in the
appliance.
33
1,4 l
8. Place an empty container
with a minimum capacity
of 1.4 litres under the cof-
fee spouts (A10) and cap-
puccino maker (A8) (g.
33).
Important! Danger
of burns
Hot water containing acid ows
out of the cappuccino maker.
Take care to avoid contact with splashes of this solution
9. Press the OK icon to conrm that you have added the
descaler solution. The message “Descale underway” is
displayed and the descaling procedure begins. The des-
caler liquid comes out of the coee spouts and cappuccino
maker and a series of rinses and pauses is performed to
remove limescale deposits from inside the machine.
After about 25 minutes, descaling stops and the messages
“RINSING”and“FILLTANK”alternate on the display.
10. The appliance is now ready for rinsing through with clean
water. Empty the container used to collect the descaler
solution. Extract the water tank, empty, rinse under run-
ning water, ll with fresh water up to the MAX level and
put back in the appliance:“RINSING, Press OK”is displayed.
11. Place the container used to collect the descaler solution
empty under the coee spouts and cappuccino maker (g.
33).
12. Press the OK icon to begin rinsing. Hot water is delivered
rst from the coee spouts to continue and end with the
cappuccino maker. The message“RINSING Please wait”ap-
pears on the display.
13. When the water tank is empty, the messages “RINSING”,
“FILL TANK” and “REPLACE FILTER” (if previously removed)
alternate on the display. Empty the container used to col-
lect the rinsing water.
14. Remove the water tank, replace the water softener lter (if
previously removed), ll the tank up to the MAX level with
2. Empty the drip tray and grounds container and wash them.
3. Check the condensate tray (A11) and empty if necessary.
4. Replace the drip tray and grounds container.
12.5 Cleaning the inside of the coee machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned o
(see section“7.Turning the appliance o”) and unplugged from
the mains power supply. Never immerse the coee machine in
water.
1. Check regularly (about once a month) that the inside of the
appliance (accessible after removing the drip tray (A14)
is not dirty. If necessary, remove coee deposits with the
brush (C5) supplied and a sponge.
2. Remove all the residues with a vacuum cleaner (g. 25).
12.6 Cleaning the water tank
1. Clean the water tank (A20) regularly (about once a month
and whenever you replace the water softener lter (C4) (if
provided) with a damp cloth and a little mild washing up
liquid.
2. Remove the lter (if present) and rinse with running water.
3. Replace the lter (if provided), ll the tank with fresh
water and replace the tank.
4. (Models with water softener lter only) Deliver about
100ml of hot water to reactivate the lter.
12.7 Cleaning the coee spouts
1. Clean the coee spouts (A10) regularly with a sponge or
cloth (g. 26).
2. Check that the holes in the coee spouts are not blocked.
If necessary, remove coee deposits with a toothpick (g.
26).
12.8 Cleaning the pre-ground coee funnel
Check regularly (about once a month ) that the pre-ground
coee funnel (A4) is not blocked. If necessary, remove coee
deposits with the brush (C5) supplied.
12.9 Cleaning the infuser
The infuser (A19) must be cleaned at least once a month.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned o (see section
“7. Turning the appliance o”).
2. Open the infuser door (A18) (g. 27) on the right side of
the appliance.

18
fresh water and insert it in the appliance. “RINSING Press
OK”will appear on the display.
15. Place the container used to collect the rinsing water empty
under the cappuccino maker (g. 33).
16. Press the OK icon to resume rinsing. Hot water is delivered
from the cappuccino maker only and the message “RINS-
ING Please wait”is displayed.
17. When it nishes, the message“Rinsing complete, Press OK”
is displayed.
18. Press the OK icon. The message “FILL TANK” is displayed.
Remove and top up the water tank with fresh water to the
MAX level and put back in the machine.
19. Empty the drip tray.
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A15) to contain water.
14. SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time estab-
lished according to water hardness.
The machine is set by default for a hardness value of 4. The ma-
chine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs to
be descaled less often.
14.1 Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
14.2 Setting water hardness
1. Press the icon (B2) to enter the menu.
2. Press (B4) or (B5) (g. 7) and select “Water
hardness”.
3. Conrm the selection by pressing the OK icon (B1) (g. 4).
4. Press or repeatedly to set the level as meas-
ured by the indicator paper (see previous section).
5. Press the OK icon to conrm the setting.
6. Press the icon to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
15. WATER SOFTENER FILTER *CERTAIN MODELS
ONLY
Certain models are tted with a water softener lter (C4). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
15.1 Installing the lter
34
1. Remove the lter (C4) from
the packaging.
2. Turn the date indicator disk
(see g. 34) until the next 2
months of use are displayed.
Please note
The lter lasts about two
months if the appliance is used
normally. If the coee machine
is left unused with the lter in-
stalled, it will last a maximum of
three weeks.
3. To activate the lter, run tap water through the hole in the
lter as shown in the gure until water comes out of the
openings at the side for more than a minute (g. 35).
35 36
0,5 L
4. Extract the tank (A20) from the appliance and ll with
water.
5. Insert the lter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (g. 37).
6. Insert the lter in the lter housing (A21) (g. 36) and
press as far as it will go.
7. Close the tank with the lid (A22) (g. 38), then replace the
tank in the machine.
37 38
When you install the lter, you must notify the appliance of its
presence.
8. Press the icon (B2) to enter the menu;
9. Press (B4) or (B5) until“Install lter”appears
on the display (B3).
10. Press the OK icon (B1) (g. 4).
11. “Enable?”is displayed.
12. Press the OK icon to conrm the selection. “HOT WATER
Press OK”is displayed.
13. Place a container underneath the cappuccino maker (A8)
(min. capacity: 500ml) (g. 5).
14. Press the OK icon to conrm the selection. The appliance
begins hot water delivery and the message“Please wait”is
displayed.
15. After the ow of hot water stops, the appliance automati-
cally resets to“Ready for coee”status.
The lter is now active and you can use the coee machine.
15.2 Replacing the lter
When “REPLACE FILTER” appears on the display (B3), after two
months (see date indicator) or when the appliance has not been
used for 3 weeks, you should replace the lter:
1. Extract the tank (A20) and exhausted lter (C4).
2. Take the new lter out of its packet and proceed as illus-
trated in points 2, 3, 4, 5, 6 and 7 in the previous section.
3. Place a container underneath the cappuccino maker (min.
capacity: 500ml).
4. Press the icon (B2) to enter the menu;
5. Press (B4) or (B5) (g. 7) until“Replace lter”
is displayed.
6. Press the OK icon (g. 4).
7. The message“Conrm?”is displayed.
soft water
slightly hard
water
hard water
very hard
water
●
● ●
● ● ●
● ● ● ●

19
2. Press (B4) or (B5) (g. 7) and select “Water
hardness”.
3. Conrm the selection by pressing the OK icon (B1) (g. 4).
4. Press or repeatedly to set the level as meas-
ured by the indicator paper (see previous section).
5. Press the OK icon to conrm the setting.
6. Press the icon to exit the menu.
The machine is now reprogrammed with the new water hard-
ness setting.
15. WATER SOFTENER FILTER *CERTAIN MODELS
ONLY
Certain models are tted with a water softener lter (C4). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
15.1 Installing the lter
34
1. Remove the lter (C4) from
the packaging.
2. Turn the date indicator disk
(see g. 34) until the next 2
months of use are displayed.
Please note
The lter lasts about two
months if the appliance is used
normally. If the coee machine
is left unused with the lter in-
stalled, it will last a maximum of
three weeks.
3. To activate the lter, run tap water through the hole in the
lter as shown in the gure until water comes out of the
openings at the side for more than a minute (g. 35).
35 36
0,5 L
4. Extract the tank (A20) from the appliance and ll with
water.
5. Insert the lter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (g. 37).
6. Insert the lter in the lter housing (A21) (g. 36) and
press as far as it will go.
7. Close the tank with the lid (A22) (g. 38), then replace the
tank in the machine.
37 38
When you install the lter, you must notify the appliance of its
presence.
8. Press the icon (B2) to enter the menu;
9. Press (B4) or (B5) until“Install lter”appears
on the display (B3).
10. Press the OK icon (B1) (g. 4).
11. “Enable?”is displayed.
12. Press the OK icon to conrm the selection. “HOT WATER
Press OK”is displayed.
13. Place a container underneath the cappuccino maker (A8)
(min. capacity: 500ml) (g. 5).
14. Press the OK icon to conrm the selection. The appliance
begins hot water delivery and the message“Please wait”is
displayed.
15. After the ow of hot water stops, the appliance automati-
cally resets to“Ready for coee”status.
The lter is now active and you can use the coee machine.
15.2 Replacing the lter
When “REPLACE FILTER” appears on the display (B3), after two
months (see date indicator) or when the appliance has not been
used for 3 weeks, you should replace the lter:
1. Extract the tank (A20) and exhausted lter (C4).
2. Take the new lter out of its packet and proceed as illus-
trated in points 2, 3, 4, 5, 6 and 7 in the previous section.
3. Place a container underneath the cappuccino maker (min.
capacity: 500ml).
4. Press the icon (B2) to enter the menu;
5. Press (B4) or (B5) (g. 7) until“Replace lter”
is displayed.
6. Press the OK icon (g. 4).
7. The message“Conrm?”is displayed.
8. Press the OK icon to conrm the selection.
9. “HOT WATER Press OK”is displayed.
10. Press the OK icon to conrm the selection. The appliance
begins hot water delivery and the message“Please wait”is
displayed.
11. After the ow of hot water stops, the appliance automatically
resets to“Ready for coee”status.
The new lter is now active and you can use the coee machine.
15.3 Removing the lter
If you want to use the appliance without the lter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Remove the tank (A20), remove the lter (C4) and put the
tank back in the appliance.
2. Press the icon (B2) to enter the menu.
3. Press (B4) or (B5) (g. 7) until “Install lter,
Enabled”appears on the display (B3).
4. Press the OK icon (B1) (g. 4).
5. “Disable?”appears on the display.
6. Press the OK icon to conrm and the icon to exit the
menu.
16. TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 1,5MPa (15 bar)
Max. water tank capacity: 1,4 l
Size LxDxH: 195x480x340 mm
Cord length: 1100 mm
Weight: 9,3 kg
Max. beans container capacity: 200 g
The appliance complies with the following EC
directives:
• European Standby Regulation 1275/2008
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
17. DISPOSING OF THE APPLIANCE
The appliance must not be disposed of with house-
hold waste, but taken to an authorised waste separa-
tion and recycling centre.