DeLonghi DEGH90W Quick guide

INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
BUILT-IN GAS
HOB
Model: DEGH90W
distributed by
DèLonghi
Pty Ltd

2
Dear Customer,
Thank you for having purchased and given your
preference to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They
will also provide a means by which to make full use of
the features offered by your appliance.
Please keep this booklet in a safe place. It may be
useful in future, either to yourself or to others in the
event that doubts should arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking
foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance or be faulty installation.
PRODUCT LABEL

3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental
rules. In particular:
■Never touch the appliance with wet hands or feet;
■do not operate the appliance barefooted;
■do not allow children or other incapable people to use the appliance
without supervision.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or illogical use of the appliance.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified
technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should
not be left around within easy reach of children, as these may cause serious injuries.
■Do not attempt to modify the technical characteristics of the appliance as
this may become dangerous to use.
■Do not carry out cleaning or maintenance operations on the appliance
without having previously disconnected it from the electric power supply.
■After use, ensure that the knobs are in off position.
■Do not allow children or other incapable people to use the appliance
without supervision.
■During and after use of the hob, certain parts will become very hot. Do not
touch hot parts.
■Keep children away from the appliance when it is in use.
■Some appliances are supplied with a protective film on steel and aluminium
parts. This film must be removed before using the appliance.
■The manufacturer declines all liability for injury to persons or damage to
property caused by incorrect or improper use of the appliance.

4
480
70
60
60 min
0
– 2
840
200 min
0
– 2
860
100
200
500
Area for
electrical connection Area for
gas connection
Figure 1
DIMENSIONS: (Note: Also refer to Figure 1 above)
General Dimensions
Width 860 mm
Depth 500 mm
Depth Below Mounting Surface 30 mm
Cut-out Dimensions
Width 840 mm
Depth 480 mm
INSTALLATION
CAUTION:
■This appliance must be installed in accordance with these installation
instructions, local gas fitting regulations, municipal building codes, water
supply regulations, electrical wiring regulations, AS5601 / NZS5261 - Gas
Installations and ony other relevant statutory regulations.
■This appliance shall only be serviced by authorized personnel.
■This appliance is to be installed only by an authorised person.
■Incorrect installation, for which the manufacturer accepts no responsibility,
may cause personal injury of damage.
■Always disconnect the appliance from mains power supply before carrying
out any maintenance operations or repairs.
■In the room where the cooker is installed, there must be enough air to
allow the gas to burn correctly, according to the current local regulations.
0
–2
0
–2

5
750 mm
60 mm min
200 mm min
500 mm
450 mm
Figure 2
CLEARANCES:
Installation clearances and protection of combustible surfaces shall comply with the
current local regulations e.g. AS5601 / NZS5261 - Gas Installations code.
Important note:
This appliance shall not be used as a space heater, especially if installed in marine
craft or caravans.
This cooktop has been designed and constructed in accordance with the following
codes and specifications:
AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335-1 General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NSZ 1044 Electromagnetic Compatibility Requirements.

6
The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind
that:
■A minimum clearance of 20 mm has to be kept between the bottom of the
cooking hob and the top of an appliance or a shelf. To ensure this clearance
mount the spacers, supplied with the appliance, as shown in the figure below.
■A partition between the base of the hob and the cupboard below should be
fitted 100 mm below the workbench surface if the cupboard is to be used
for storage.
■Overhead clearances - In no case shall the clearance between the highest
part of the hob and a range hood be less than 600 mm, or for an overhead
exhaust fan, 750 mm. Any other downward facing combustible surface less
than 600 mm above the highest part of the hob shall be protected for the full
width and depth of the cooking surface area in accordance with local regula-
tions in force. However, in no case shall this clearance to any surface be less
than 450 mm.
■Side clearances - Where the dimension from the periphery of the nearest
burner to any vertical combustible surface is less than 200 mm, the surface shall
be protected in accordance with with local regulations in force to a height of
not less than 150 mm above the hob for the full dimension (width or depth) of
the cooking surface area.
Where the dimensions from the periphery of the nearest burner to any vertical
combustible surface is less than 200 mm, the horizontal surface shall be greater
than 10mm below the surface of the hob, or the horizontal surface require-
ment above.
■Protection of combustible surfaces - Local regulations in force specify that
where required protection shall ensure that the surface temperature of the com-
bustible surface does not exceed 65 °C above ambient. The fixing of 5 mm
thick ceramic tiles to the surface or attaching fire resistant material to the surface
and covering with sheet metal with minimum thickness of 0.4 mm should be
satisfactory.
Figure 3
20 mm

7
INSTALLATION (Refer to Figure 4):
1. Spread out the gasket “C” over the workbench at the edge of the cut out tak-
ing care to overlap the gasket at the corners.
2. Slot in the cooking hob into the cut out of the workbench and locate it cor-
rectly.
3. Adjust the clamps “A” and tighten the screws “B” until the hob is firmly secured.
4. Using a sharp tool, trim any excess gasket which protrudes from the edge of
the hob. Take care not to damage the countertop.
Figure 4
;;;
;;;;;;;;;
;;;;;;;;;
20 mm min. 40 mm max.
B
C
A

8
GAS SUPPLY:
■The connection must be executed by an authorised person according to the relevant
standards.
■Before connecting the appliance to the gas main, mount the brass conical adaptor
onto the gas inlet pipe, upon which the gasket has been placed (figures 5a-5b).
Conical adaptor and gasket are supplied with the appliance (packed with conversion
kit for use with Natural gas or Universal LPG).
■This appliance is suitable for use with Natural Gas or Universal LPG. (Check the “gas
type” sticker attached to the appliance).
■For Natural Gas models the gas supply is connected to the pressure regulator which
is supplied with the appliance (fig. 5a). Adjust the regulator to obtain a test point
pressure of 1 kPa with the dual (DB) burner operating at the maximum (inside and
outside flames in simultaneously at the maximum).
■For Universal LPG models the gas supply is connected to the test point adaptor
which is supplied with the appliance (fig. 5b) and ensure that the supply pressure is
regulated to 2.75 kPa.
■Do NOT force the ”elbow“ rotation prior to loosening nut.
■Do NOT over tighten the nut at the ”elbow“.
Figure 5b
Figure 5a
Gas connection for
UNIVERSAL LPG
Test point adaptor
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Gas inlet pipe
Test
point
Gas connection for
NATURAL GAS
Gas inlet pipe
Gasket
Brass conical adaptor
(Thread tight: use
suitable seal)
Gas regulator
Test
point

9
1. After connecting the gas supply, check the piping and connections for leaks using a
soap and water solution. The presence of bubbles indicates a leak, tighten or
replace connections as appropriate.
Warning: Do not use any naked flame to check for leaks.
2. The operation of the appliance MUST be tested before leaving.
3. Adjust the test point pressure or supply pressure to the value which is appropriate
for the gas type.
4. Turn on the appliance gas controls and light each burner. Check for a well defined
blue flame without any yellow tipping. If any abnormality is evident then check that
the burner cap is located properly and the injector nipple is aligned correctly.
5. Check the minimum burner setting by quickly rotating the gas control knob from
the maximum to the minimum position, the flame must not go out. If adjustment is
required carry out the “minimum burner setting adjustment" procedure described
below.
6. If satisfactory performance cannot be obtained, the installer shall check the installa-
tion and notify the local gas supply authority for a gas supply problem, or if it is an
appliance problem, our Customer Service Centre should be called to obtain the
nearest authorized Delonghi Service Agent.
7. Where the appliance data plate cannot be easily read with the appliance in the
installed position the duplicate data plate must be attached to adjacent surface and
the duplicate Natural gas / ULPG conversion label should also be included where a
Natural gas / ULPG conversion has been completed.
INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY
■If this appliance has to be installed with a hose assembly, the installer shall refer
to the network operator or gas supplier for confirmation of the gas type, if in
doubt.
■Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified.
The thread connection shall be Rp 1/2” (ISO 7-1) male.
■IMPORTANT WARNING: After connection the installer must check that the
hose is not kinked, subjected to abrasion or permanently deformed.
The installer must check also that the hose is not near (or in contact) with any hot
surfaces e.g. base of metal hotplate, underbench oven etc.
■The hose assembly shall be as short as practicable and comply with relevant
AS5601 / NZS5261 requirements.
■IMPORTANT WARNING: The installer shall ensure the hose assembly is
restrained from accidental contact with the flue outlet of an underbench oven.
■When used with a flexible hose, the connector on the wall should be between
800 mm to 850 mm above the floor and in the region outside the width of the
appliance to a distance of 250 mm.
The supply connection point shall be accessible with the appliance installed.

10
TABLE FOR THE CHOICE OF THE INJECTORS
Natural gas Universal LPG
Test Point Pressure [kPa]
1.0 2.75
BURNER
Auxiliary (A)
0.85 3.60 0.53 3.60
Semi-rapid (SR)
1.12 6.30 0.70 6.30
Triple-ring (TR) 1.6012.70
0.95 11.90
Dual (DB) 0.90 (no.1 central) 3.90 (*) 0.50 (no.1 central) 3.10 (*)
Gas
Consumption
[MJ/h]
Injector
Orifice Dia.
[mm]
Gas
Consumption
[MJ/h]
Injector
Orifice Dia.
[mm]
Inner crown
Outer crowns 1.20(no.2 outer) 15.90 (#) 0.66 (no.2 outer) 14.10 (#)
(*) Power calculated with only inner crown operating.
(#) Power calculated with inner and outer crowns operating.
CONVERSION PROCEDURE (to convert to Natural gas or to
ULPG) REPLACING THE INJECTORS
The conversion procedure must be carried out only by an authorised person.
This appliance is suitable for use with Natural gas or Universal LPG (check the “gas
type” sticker attached to the appliance). The nominal gas consumption and injector
size details are provided in the table above.
To replace the injectors proceed as follows:
■Remove pan supports and burners from the cooktop.
■Using a spanner, remove the injector J (figs. 6a, 6b, 7) and replace it with one
according to the gas type (see table above).
■ Affix to the appliance the warning label stating that the cooktop has been convert-
ed for use with Natural gas / ULPG (supplied with the Natural gas / ULPG conver-
sion kit.).
A second Natural gas / ULPG conversion label should also be affixed to an adjacent
surface along with the duplicate data plate.
IMPORTANT
■If the cooktop is suitable for use with Natural gas and must be converted for
use with Universal LPG, before connecting to gas main remove the appliance
gas regulator and replace with test point adaptor (see fig. 5a, 5b)
■If the cooktop is suitable for use with Universal LPG and must be converted for
use with Natural gas, before connecting to the gas main remove the appliance
test point adaptor and replace with gas regulator (see figs. 5a, 5b).
NOTE:
Gas regulator and test point adaptor are supplied with the appliance (packed with
conversion kit)
The burners are designed so that regulation of primary air is not required.

11
Figure 6a Figure 6b
J
J
Dual
burner
J
Injector for inner crown
J
Injectors for
outer crowns
Triple-ring
burner
Auxiliary
and
semi-rapid
burners
Figure 7

12
MINIMUM BURNER SETTING ADJUSTMENT
Check whether the flame spreads to all burner ports when the burner is lit with the
gas tap set to the minimum position. If some ports do not light, increase the minimum
gas rate setting.
Check whether the burner remains lit even when the gas tap is turned quickly from
the maximum to the minimum position. If the burner does not remain lit, increase the
minimum gas rate setting.
The procedure for adjusting the minimum gas rate setting is described below.
Figure 8 Figure 9
A
Auxiliary, semi-rapid and triple ring burners
■Light the burner.
■Set the gas valve to position.
■Remove the knob.
■With a thin screwdriver turn the screw Funtil adjustment is correct (fig. 8).
Inside crown of Dual burner
■Light the DUAL burner.
■Set the gas valve to position.
■Remove the knob.
■Using a screwdriver turn the screw Huntil the correct setting is obtained (fig. 9).
Outside crowns of Dual burner
■Light the DUAL burner.
■Set the gas valve to position.
■Remove the knob.
■Using a screwdriver turn the screw Guntil the correct setting is obtained (fig. 9).
For Universal LPG gas, tighten the adjustment screws completely.
HG
H
G

13
INSTALLATION
ELECTRICAL REQUIREMENTS
■The appliance must be connected to the mains checking that the voltage
corresponds to the value given in the rating plate and that the electrical
cable sections can withstand the load specified on the plate.
■The plug must be connected to an earthed socket in compliance with safety
standards.
■If the appliance is supplied without plug, fit a standard plug which is
suitable for the power consumed by the appliance.
■The wires in the power cable are coloured in accordance with the following
code: Green/Yellow = Earth, Blue = Neutral, Brown = Active.
If the colours of the wires in the power cable to the appliance do not
correspond with the coloured markings identifying the terminals in the
junction terminal, proceed as follows:
1.The wire which is coloured green and yellow must be connected to the
terminal marked E (Earth) or coloured Green.
2.The wire which is coloured blue must be connected to the terminal marked
N (Nuetral) or coloured Black.
3.The wire which is coloured brown must be connected to the terminal
marked L (Live) or A (Active) or coloured Red.
■The appliance must be connected directly to the mains placing a two pole
switch with minimum opening between the contacts of 3 mm between the
appliance and the mains.
■The power supply cable must not touch the hot parts and must be
positioned so that it does not exceed 50°C above ambient.
■Once the appliance has been installed, the switch or socket must always be
accessible.
■ If the supply cord is damaged it must be replaced by the manufacturer or it’s
Service Agent or a similarly qualified person in order to avoid a hazard.
N.B. The connection of the appliance to earth is mandatory.
If the installation requires alterations to the domestic electrical system call a qualified elec-
trician.
He should also check that the socket cable section is suitable for the power drawn by
the appliance.

14
NL
M
PA
CA
CA
CA
CA
CA
PA PA PA PA
A
Figure 10
Replacing the power cord must be done by a qualified electrician in
accordance with the instructions supplied by the manufacturer and in
compliance with established electrical regulations.
ELECTRIC DIAGRAMS KEY
PA Ignition switch
A Ignition coil
M Terminal block
CA Spark electrode

15
USE and CARE
CAUTION:
■This appliance must be used only for the task it has explicitly been designed for,
that is for domestic cooking of foodstuffs. Any other form of usage is to be con-
sidered as inappropriate and therefore dangerous. Do not use this appliance as
a space heater.
■Do NOT place combustible materials or products on this appliance at any time.
■Do NOT spray aerosols in the vicinity of this appliance while it is in use.
■Before using for the first time, clean the cooktop with warm soapy water.
■Use the coffee pot support to ensure that small cooking utensils are stable.
■IMPORTANT NOTE: This appliance shall not be used as a space heater,
especially if installed in marine craft or caravans.
■Do NOT use or store flammable materials near this appliance.
■Do NOT modify this appliance.

16
Figure 11
CONTROL PANEL
10. Auxiliary burner control knob (1)
11. Triple-ring burner control knob (2)
12. Dual burner control knob (3)
13. Left semi-rapid burner control knob (4)
14. Right semi-rapid burner control knob (5)
GAS BURNERS Natural Gas Universal LPG
MJ/h MJ/h
1. Auxiliary burner (A) 3.6 3.6
2. Triple ring burner (TR) 12.711.9
3. Dual burner (DB) 3.9(*) 3.1(*)
15.9(#) 14.1 (#)
4. Left semi-rapid burner (SR) 6.3 6.3
5. Right semi-rapid burner (SR) 6.3 6.3
■This appliance is class 3
rated
■The electric ignition is
incorporated into the
knobs
■The appliance has a safety
valve system fitted (beside
every burner there is the
“T” probe as in fig. 16 - not
confuse with the “S” elec-
trode of the electronic igni-
tion) the flow of the gas
will stopped if and when
the flame should acciden-
tally go out.
GAS HOB
(*) : Power calculated with only inner crown operating.
(#) : Power calculated with inner and outer crowns operating.
14
13
12
11
10






17
USING GAS BURNERS
■Check that the electricity is switched on to allow spark ignition.
■Make sure that all controls are turned to zero.
■The gas flow to the burner is controlled by the knobs on the safety taps.
■You control the flow by turning the knob indicator to line up with the following
symbols:
– Symbol : tap closed
(burner off)
– Symbol : High (maximum)
– Symbol : Low (minimum)
■You can control the temperature by the knob to “High” from “Minimum”.
■To switch off, turn the knob clockwise until you hear the safety click.
■Note that, if you are using a burner at the minimum setting, you turn the knob
clockwise past the maximum setting before reaching the off position.
■Whenever lighting any of the burners produces an abnormal flame, switch that
burner off and relight using the minimum setting.
■If after relighting the burner, the flame is still abnormal, turn the burner off and
contact our Customer Service Centre to obtain the nearest authorized Delonghi
Service Agent.
■In the case of a mains failure light the burner with a match or lighted taper.
■Note: When the cooker top is not being used, set the gas knobs to their
closed positions and also close the cock valve on the gas bottle or the main
gas supply line.
Figure 12a
Auxiliary, Semi-rapid and Triple-ring burners

18
In order to light the burner, you must:
1 – Turn the knob fig. 12a in anti-clockwise direction up to the maximum aperture
(symbol ), push in and hold the knob; this will light the gas.
2 – Wait for about ten seconds after the gas burner has been lit before letting go
of the knob (valve activation delay).
3 – Adjust the gas valve to the desired position.
Important
■If the burner flame should go out, the safety valve will automatically stop the
gas flow.
■To re-light the burner, return the knob to the closed position, wait for at
least 1 minute and then repeat the lighting procedure.
■N.B. If your local gas supply makes it difficult to light the burner with the knob
set to maximum, set the knob to minimum and repeat the operation.
Knob
position Function Auxiliary and Semi-rapid
burners
Triple-ring burner
closed
valve
maximum
rate
minimum
rate
0
LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Auxiliary, Semi-rapid and Triple-ring burners)

USING GAS BURNERS
Dual burner
The Dual Burner is a very flexible burner which allows different regulations and optimal
cooking.
It is composed by one inner and two outer crowns; the flame of the inner crown can be
regulated separately from the flames of the outer crowns.
The Dual Burner can be used:
■as a small burner (flame produced only by the inner crown) which can be
adjusted from the maximum ( )to the minimum ( )position.
Intermediate operating adjustments can be achieved by positioning the indicator
between the maximum and minimum opening positions, and never between the
maximum opening and position.
■as a high-power burner (all flames produced simultaneously by inner and outer
crowns) which can be adjusted from the maximum ( )to the minimum
()position.
Gas flow to the burner is adjusted by turning the knob (illustrated in fig. 12b) which
control the valve.
Knob
position Function Dual burner
maximum rate of inner crown
(only inner flame at the maximum)
closed
valve
minimum rate of inner crown
(only inner flame at the minimum)
maximum rate of inner + outer crowns
(inside and outside flames in
simultaneously at the maximum)
minimum rate of inner + outer crowns
(inside and outside flames in
simultaneously at the minimum)
Turning the knob so that the knob indicator lines up with the symbols printed on the
control panel achieves the following functions:
19

LIGHTING GAS BURNERS FITTED WITH FLAME FAILURE
SAFETY DEVICE (Dual burner)
In order to light the burner, you must:
1 – Push and turn the knob in an anti-clockwise direction up to the position
(maximum rate of inner crown); push in and hold the knob until the flame has been
lit.
The sparks produced by the lighter situated inside the relative burner will light the
flame.
In the event that the local gas supply conditions makes it difficult to light the burn-
er in position, try again with the knob in position.
If there is no mains electrical supply connection, bring a lighted match close to the
burner.
2 – Wait for about ten seconds after the gas burner has been lit before letting go the
knob (safety device activation delay).
2 – Adjust the gas valve to the desired position.
If the burner flame should go out for some reason, the safety valve will automatically
stop the gas flow.
To re-light the burner, return the knob to the closed position ( ), wait for at least 1
minute and then repeat the lighting procedure.
Note: To change from using the inner crown only to using both the inner and outer
crowns together, press the control knob down before turning it.
You have to do the same when going from using both crowns to using just the
inner crown.
Figure 12b
20