Delta Associate DIGITAL PROJECTION E-Vision Laser 9000... Operating manual

Rev A December 2019 120-255
E-Vision Laser 9000 Series
Super High Brightness Digital Video Projector
Important Information

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 2
Important Information
Digital Projection
Digital Projection Asia
16 New Industrial Road
#02-10 Hudson Technocentre
Singapore 536204
Tel [phone]
Fax [phone]
www.digitalprojectionasia.com
Digital Projection Inc.
55 Chastain Road, Suite 115
Kennesaw, GA 30144, USA
Tel [phone]
Fax [phone]
[email protected]
www.digitalprojection.com
Digital Projection China
中国 北京市 朝阳区 芍药居北里101号
世奥国际中心A座2301室(100029)
Rm A2301
ShaoYaoJu 101 North Lane
Shi Ao International Center
Chaoyang District
Beijing 100029, PR CHINA
Tel [phone]
Fax [phone]
[email protected]
www.dp-china.com.cn
Digital Projection Limited
Greenside Way, Middleton
Manchester M24 1XX, UK
Registered in England No. 2207264
Registered Oce: as above
Tel [phone]
Fax [phone]
[email protected]
[email protected]
www.digitalprojection.co.uk
Digital Projection Taiwan
186 Ruey Kuang Rd, Neihu District,
Taipei, 114 Taiwan
Tel [phone] x8854
T[email protected]
Digital Projection Japan
〒105-0012 東京都港区芝大門2-1-14
2-1-14 Shibadaimon, Minato-ku,
Tokyo, Japan 105-0012
[email protected]
www.digitalprojection.com/jp
Digital Projection FZE
Unit B4, Light Industrial Units 4,
Silicon Oasis, Dubai, UAE
Tel [phone]
[email protected]
www.digitalprojection.com
Digital Projection Korea
1511, Byucksan Digital Valley 6-cha,
Gasan-dong, Geumcheon-gu,
Seoul, Korea
Tel [phone] #1417
[email protected]
Digital Projection India
[email protected]

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 3
Important Information
Super High Brightness Digital Video Projector
Important Information
Full information about operating, connecting and setting up the projector can be found in the User
Guides.
Please use the QR code (also located on the projector) to access the latest
E-Vision projector user guides and other documentation via the Digital Projection
website.
Or visit the products specication page on the Digital Projection website to
download the latest user guide and other documentation.
Contents
Symbols used in the User Manual...............................................................................................4
Electrical and physical specications........................................................................................5
Laser precautions.............................................................................................................................5
Product labels....................................................................................................................................6
Location of laser aperture..............................................................................................................7
Interlock switches ............................................................................................................................7
General precautions ........................................................................................................................8
Installation precautions ..................................................................................................................9
Operation and conguration precautions ...............................................................................11
Compliance with international standards ...............................................................................12
RF Interference.............................................................................................................................12
Noise .............................................................................................................................................12
European Waste Electrical and Electronic Equipment (WEEE) Directive ..............................12
Basic Operation Instructions ......................................................................................................13
Positioning the screen and projector.........................................................................................13
Connecting the power supply.....................................................................................................14
Switching the projector on..........................................................................................................14
Switching the projector o..........................................................................................................14
Selecting an input signal.............................................................................................................15
Selecting a test pattern................................................................................................................15
Adjusting the image.....................................................................................................................15
Adjusting the lens ........................................................................................................................16
Inserting a new lens.....................................................................................................................17
Removing the lens .......................................................................................................................18
Control Panel Reference...............................................................................................................19
Projector indicators .....................................................................................................................20
Remote Control Reference ..........................................................................................................21
E-Vision User Guides
Follow link for Projector Documentation
この二次元バーコードをスキャンしてプロジェクターのデータを取得してください
请扫描条码来取得投影机的文件
프로젝터 설명서를 보려면 링크를 팔로우하십시오
Suivre le lien pour accéder à la documentation du projecteur
Produktdokumentation nden Sie unter dem Link

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 4
Important Information
Symbols used in the User Manual
LASER WARNING: this symbol indicates that there is a potential hazard of eye
exposure to laser radiation unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical
shock unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself
and/or damage to the equipment unless the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Electrical and physical specications
Main Voltage 100 - 240VAC 50/60Hz single phase 10.0A
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Operating Humidity 10% to 85% non-condensing
Dimensions: L: 525mm (20.6in) x W: 470mm (18.5in) x H: 220.5mm (8.6in)
Weight 25Kg 55.1lb (projector p/n: 120-481) with lens
Power Consumption at 100 VAC 1000 W typical (Normal Mode)
at 200 VAC 950 W typical (Normal mode)
Thermal Dissipation at 100 VAC 3410 BTU/Hour typical (Normal mode)
at 200 VAC 3240 BTU/Hour typical (Normal mode)
Fan Noise: 44 dBA Typical (Normal Mode)
Specications are subject to change without notice.

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 5
Important Information
Laser precautions
Projector
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or reected toward other people or
reective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included
instructions are not followed.
Caution – use of controls or adjustments or performance of procedures other than
those specied herein may result in hazardous radiation exposure.
Non-laser emission. There remains non-laser emission from the projection lens. This
portion of emission has been tested per IEC/EN 62471 to be Risk Group 2 (low risk).
Laser Parameters:
Wavelength 450nm - 460nm (Blue)
Mode of operation Pulsed, due to frame rate
Pulse duration 1.34ms
Pulse repetition rate 120Hz
Maximum pulse energy 0.698mJ
Total internal power >100W
Apparent source size >10mm, at lens stop
Divergence >100 mili Radian
Remote Control - Laser Pointer
CLASS 2 LASER PRODUCT
This Laser Product is designated as Class 2 during all
procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow laser light to be directed or
reected toward other people or reective objects.
激光辐射勿直视激光束
2类 激 光产品
波 长 ：6 4 0 -66 0 n m
最大输出 ：1mW
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGTH: 640-660nm
MAX OUTPUT: <1mW
CLASS II LASER PRODUCT
ÉVITEZ L'EXPOSITION - UN RAYONNEMENT LASER
EST ÉMIS PAR CETTE OUVERTURE RAYONNEMENT LASER
NE REGARDEZ PAS DIRECTEMENT LE RAYONNEMENT
ADVANCETECH CO., LTD (FACTORY)
11/F-1, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei
City 23584, Taiwan, R.O.C.
WAVELENGTH:640-660nm
MAX OUTPUT:<1mw
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50 dated June
24.2007. IEC/EN60825-1:2007
P/N: SN1411010 Product code:1512010
IEC/EN 60825-1:2007 IEC/EN 60825-1:2014
波 長 ：6 4 0 -66 0 n m
最大輸出 ：1 m W
雷射輻 射 勿注視波束
等級2雷射產品

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 6
Important Information
Product labels
Manufacturers ID Label
Explanatory Label
Laser Aperture Label
User Guides Label
DLP Projector / Projecteur
(數位投影機 / 數字投影機)
326xxxxxxx XXXXX XXXXX
Made in China/製造地:中國/制造地:中國
Digital Projection Limited
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
201910
E-Vision Laser 9000-WU
02-2060-8574
R41086
RoHS
Model Name / Modèle(型 號 / 型號): E-Vision Laser 9000-WU 
INPUT / Entrée(輸入 / 輸 入):10 0-240V 50/60Hz 10.0A
This device complies with Part 15 of the FCC rules, Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
CAN I CES-3(B) / NMB -3(B).
Caution: Do not open, No user serviceable parts inside.
警告: 請勿打開外殼, 設備內無服務性維修之元件.
警告: 請勿打開外殼, 設備內無服務性維修之元件.
Cuidado: no abra la tapa. Niguna parte interna es reparable por Usuario.
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
Caution: Do not open, No user serviceable parts inside.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
Apparatets stikprop skal tilsluttes en stikkontakt med jord,
som giver forbindelse til stikproppens jord
110.0 mm
125.0 mm
Complies with FDA performance standards
for laser products except for deviations
pursuant to Laser Notice No. 50, dated
June 24, 2007
RAYONNEMENT LASER
EXPOSITION DIRECTE DANGEREUSE POUR LES
YEUXAPPAREIL À LASER DE CLASSE 3R
longueur d'onde : 450-460 nm
maximum énergie de impulsion : 0.698 mJ,
durée de impulsion : 1.34 ms
GB 7247.1-2012 / IEC/EN 60825-1:2007
LASER RADIATION AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Emitted wavelength : 450-460 nm
Max. Pulse energy: 0.698 mJ, Pulse duration: 1.34 ms
3R
: 450-460 nm
0698 mJ1.34 ms
雷射輻射 避免眼睛受到直接照射 3R類雷射產品
波⻑: 450-460 nm
最⼤脈衝能量: 0.698 mJ, 脈衝時間: 1.34 ms
326 23147 00
CLASS 1 LASER PRODUCT IEC/EN 60825-1:2014
PRODUIT LASER DE CLASSE 1 IEC/EN 60825-1:2014
70.0
70.0
E-Vision User Guides
Follow link for Projector Documentation
この二次元バーコードをスキャンしてプロジェクターのデータを取得してください
请扫描条码来取得投影机的文件
프로젝터 설명서를 보려면 링크를 팔로우하십시오
Suivre le lien pour accéder à la documentation du projecteur
Produktdokumentation nden Sie unter dem Link
DLP Projector / Projecteur
(數位投影機 / 數字投影機)
326xxxxxxx XXXXX XXXXX
Made in China/製造地:中國/制造地:中國
Digital Projection Limited
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
201910
E-Vision Laser 9000-WU
02-2060-8574
R41086
RoHS
Model Name / Modèle(型 號 / 型號): E-Vision Laser 9000-WU 
INPUT / Entrée(輸入 / 輸 入):10 0-240V 50/60Hz 10.0A
This device complies with Part 15 of the FCC rules, Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
CAN I CES-3(B) / NMB -3(B).
Caution: Do not open, No user serviceable parts inside.
警告: 請勿打開外殼, 設備內無服務性維修之元件.
警告: 請勿打開外殼, 設備內無服務性維修之元件.
Cuidado: no abra la tapa. Niguna parte interna es reparable por Usuario.
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient aucune pièce
interne réparable par l’utilisateur.
Caution: Do not open, No user serviceable parts inside.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
Apparatets stikprop skal tilsluttes en stikkontakt med jord,
som giver forbindelse til stikproppens jord
110.0 mm
125.0 mm
Complies with FDA performance standards
for laser products except for deviations
pursuant to Laser Notice No. 50, dated
June 24, 2007
RAYONNEMENT LASER
EXPOSITION DIRECTE DANGEREUSE POUR LES
YEUXAPPAREIL À LASER DE CLASSE 3R
longueur d'onde : 450-460 nm
maximum énergie de impulsion : 0.698 mJ,
durée de impulsion : 1.34 ms
GB 7247.1-2012 / IEC/EN 60825-1:2007
LASER RADIATION AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Emitted wavelength : 450-460 nm
Max. Pulse energy: 0.698 mJ, Pulse duration: 1.34 ms
3R
: 450-460 nm
0698 mJ1.34 ms
雷射輻射 避免眼睛受到直接照射 3R類雷射產品
波⻑: 450-460 nm
最⼤脈衝能量: 0.698 mJ, 脈衝時間: 1.34 ms
3262314700
CLASS 1 LASER PRODUCT IEC/EN 60825-1:2014
PRODUIT LASER DE CLASSE 1 IEC/EN 60825-1:2014
70.0
70.0

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 7
Important Information
Label Locations
1Location of Hazard
Warning Symbol and
Laser Aperture Label
on the body of the
projector
2Location of
Manufacturer’s ID
Label and Explanatory
Label with Certication
Statement and Risk
Statement on the body
of the projector
3Location of User Guides
Label on the body of the
projector
1
2
3

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 8
Important Information
Location of laser aperture
The laser aperture is located as indicated below. Be careful not to expose the eye to direct
laser light.
1Laser aperture
Interlock switches
Interlock switches are installed at the main frame, inside the cover. These will power-o󰀨 the
system individually when activated.
1 Will be activated when the projection lens is removed or misplaced.
2 Will be activated when the top cover is removed.
1
12

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 9
Important Information
General precautions
The unit is never to be operated if the unit is defective or the cover or seal is damaged.
No maintenance allowed by end user.
Do not open the cabinet. There are no user serviceable parts inside.
No service is allowed except by authorized personnel.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equipment MUST be
earthed.
Take care to prevent small objects such as paper or wire from falling into the projector.
If this does happen, switch o󰀨 immediately, and have the objects removed by
authorised service personnel.
Do not expose the projector to rain or moisture, and do not place any liquids on top of
the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power
cable.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could cause a re
Always allow the projector to cool for 5 minutes before disconnecting the power or
moving the projector.
Never use strong detergents or solvents such as alcohol or thinners to clean the
projector and lens.
RISK GROUP 2 CAUTION. Possibly hazardous optical radiation emitted from this
product. Do not stare at operating light source. May be harmful to the eyes.

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 10
Important Information
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar connectors
may have a dangerously high voltage source.
The projector must be installed only by suitably qualied personnel, in accordance with
local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an
emergency.
Allow at least 50cm (19.7in) of space between the ventilation outlets and any wall, and
30cm (11.8in) on all other sides.
Do not install the projector close to anything that might be a󰀨ected by its operational
heat, for instance, polystyrene ceiling tiles, curtains etc.
Place the projector in a dry area away from sources of dust, moisture, steam, smoke,
sunlight or heat.
The projector is heavy. Use safe handling techniques when lifting the projector.
Do not drop or knock the projector.
Before installation, make sure that the surface, ceiling or rigging that is to support the
projector is capable of supporting the combined weight of the projector and lens.
Do not place heavy objects on top of the projector chassis.
Backup safety chains or wires should always be used with ceiling mount installations.
The projector can be operated any position, as shown in the diagram:
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air
temperature within the enclosure does not exceed operation temperature while the
projector is running, and the air intake and exhaust vents are unobstructed.
All enclosures should pass a certied thermal evaluation to ensure that the projector
does not recycle exhaust air, as this may cause the device to shutdown even if the
enclosure temperature is with the acceptable operation temperature range.
Turn on High Fan Speed Mode when located in high altitude areas.
360°
Pitch
360°
Roll

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 11
Important Information
When installing a ceiling mount, make sure the weight limit is not exceed and the
projector is rmly secured.
Avoid installing near an air conditioner duct or a subwoofer.
Avoid installing at high temperature, insu󰀩cient cooling and heavy dust locations.
Keep your product away from uorescent lamps (>1 Meter) to avoid malfunction caused
by IR interference.
A VGA IN connector should be used to connect to the VGA IN port on the projector. It
should be inserted tightly, with the screws on both sides securely fastened to ensure
proper connection of the signal wire for achieving optimal display e󰀨ect.
An AUDIO IN connector should be used to connect to the AUDIO IN port on the
projector. It CANNOT be connected to AUDIO OUT or other ports like BNC, RCA;
otherwise, it will lead to mute output and even DAMAGE the port.
The power cord and signal cable should be connected before the projector is powered
on. During startup and operation, DO NOT insert or remove the signal cable or the
power cord to avoid damaging the projector.
The projector generates heat during use. The internal fans dissipate the heat of the
projector when shutting down, which could continue for a certain period. After the
projector enters STANDBY MODE, remove the power cord. DO NOT remove the power
cord during shutdown as it may cause damage to the projector and may a󰀨ect the
service life of the projector.
When using projectors in environments with third party high power laser systems avoid
direct laser beams pointing towards the projection lens. This may cause incident light
to converge into the optical engine and cause damage to the DLP DMD.
Please pay attention to projector installation with respect to other staging laser light
equipment set-up. These systems can cause permanent damage to the DMD imaging
devices used in our projectors. This damage is not covered by our warranty.
Make sure the lens cap is removed from the rear of the lens before it is inserted into the
projector.
Make sure the lens caps are removed from the lens before operating the projector. Light
energy levels have been known to cause damage to both the lens and projector optics.
This damage is not covered by our warranty.
Operation and conguration precautions
Do not make changes to the networking conguration unless you understand what you
are doing, or have taken advice from your Network Manager. If you make a mistake,
it is possible that you will lose contact with the projector. Always double-check your
settings before pressing the APPLY button. Always keep a written note of the original
settings, and any changes you have made.
Software updates should NOT be carried out except by, or with the supervision of,
Digital Projection Service personnel.

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 12
Important Information
Compliance with international standards
RF Interference
FCC
The Federal Communications Commission does not allow any modications or changes to the unit
EXCEPT those specied by Digital Projection in this manual. Failure to comply with this government
regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the
user will be responsible for correcting any interference.
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 45 dB (A) according to ISO 3744 or ISO 7779.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic
Equipment. Our products are designed with reuse, recycling and recovery of all components
in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or
its agent so that the environmental impact can be minimised.

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 13
Important Information
Whats in the Box?
Projector
Remote control
2x AAA batteries
Important Information HDMI cable Remote cable
Power Cable
UK/ROW
Power Cable
EU
Power Cable
China
Power Cable
USA

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 14
Important Information
Basic Operation Instructions
Positioning the screen and projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll
the screen. Set the adjustable feet so that the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling
mounting.
1Two adjustable feet (front)
2Six M6 holes for ceiling mount
The screws should not penetrate more than 12mm max into the body of the projector.
3 Two xed length feet (rear)
Do not use the threaded holes for the adjustable feet to hang or mount the projector.
1
2
3
1
3
2
2
2
2
2

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 15
Important Information
Connecting the power supply
Firmly push the mains
connector into the AC IN
socket.
Use only the power cable provided.
Ensure that the power outlet includes a ground connection as this equipment MUST be
earthed.
Handle the power cable carefully and avoid sharp bends. Do not use a damaged power
cable.
Switching the projector on
1. Connect the power cable between the mains supply and the projector. (See Connecting the
power supply above.)
2. The POWER indicator lights green to indicate that the projector is in STANDBY mode. Press one
of the following buttons:
• On the remote control, the ON button
• On the projector control panel, the POWER button.
The POWER indicator begins ashing green and the fans start. The POWER indicator lights
steady Green when the projector is fully switched on.
Switching the projector o󰀨
1. Press OFF on the remote control or POWER on the control panel, then press again to conrm
your choice. The POWER indicator light will ash green until the cool down period has completed,
then goes steady green to indicate that the projector has entered STANDBY mode.
2. If you need to switch the projector o󰀨 completely, disconnect the power cable from the projector.
1
1

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 16
Important Information
Selecting an input signal
If more than one input source is connected, select the input you want to display. Press the Source
button on the control panel and use the UP ▲ and DOWN ▼ arrow buttons to scroll through the list of
inputs:
• HDMI 1
• HDMI 2
• DVI
• VGA
• BNC
• Composite Video
• HDBaseT
Selecting a test pattern
1. Press the MENU button to open the OSD.
2. Press the LEFT ◄ and RIGHT ► arrow buttons to navigate to the Settings 1 menu.
3. Press the UP ▲ and DOWN ▼ arrow buttons to move to the Advanced 2 submenu and then
press (ENTER) to open the submenu. Once inside, press UP ▲ and DOWN ▼ to highlight
Test Pattern.
4. Use the LEFT ◄ and RIGHT ► arrow buttons to cycle through the available test patterns.
Test patterns are: None, RGB Ramps, Color Bars, Step Bars, Checkboard, Grid, Horizontal Lines,
Vertical Lines, Diagonal Lines, Horizontal Ramp, Vertical Ramp, White, Red, Green, Blue,
Black.
Adjusting the image
Orientation
• This can be set from the Setttings 1 menu.
Highlight Projection and choose from Normal, Rear, Ceiling and Rear+Ceiling.
Keystone
To adjust keystone, press the Keystone button on the remote control to open the Keystone menu,
and then use the arrow buttons for vertical or horizontal keystone corrections.
Picture
• Settings such as Gamma, Brightness,Contrast and Sharpness can be set from the Image
menu.

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 17
Important Information
Adjusting the lens
Lens shift
The lens shift function can be used to adjust the position of the projected image either horizontally or
vertically.
Use the vertical and horizontal lens shift knobs to move the image across the width or height of the
screen.
1Horizontal lens shift knob
2Vertical lens shift knob
Focus and zoom
Use the focus 1and zoom 2rings on
the projector lens to adjust focus and zoom.
12
1 2

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 18
Important Information
Inserting a new lens
Before changing the lens, always make sure the projector is switched o󰀨 and fully
disconnected from its power supply.
When changing the lens, avoid using excessive force as this may damage the
equipment.
Avoid touching the surface of the lens as this may result in image impairment.
The lens is shipped separately.
Take care to preserve the original lens packaging and protective caps for future use.
The projector will not power on without the lens tted.
1. Use the ange to
align the lens with
the socket.
2. Firmly push the lens into
the socket.
3. Turn the lens clockwise
until it clicks into place.
1
1

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019 Page 19
Important Information
Removing the lens
Before changing the lens, always make sure the projector is switched o󰀨 and fully
disconnected from its power supply.
When changing the lens, avoid using excessive force as this may damage the
equipment.
Avoid touching the surface of the lens as this may result in image impairment.
The lens is shipped separately.
Take care to preserve the original lens packaging and protective caps for future use.
The projector will not power on without the lens tted.
1. Push in the lens
release button.
2. Turn the lens anti-
clockwise.
3. Slowly pull the lens out of
the socket.
1
1

Digital Projection E-Vision Laser 9000 Series
Rev A December 2019
Page 20
Important Information
Control Panel Reference
MENU
Opens and exits OSD menus.
Keystone LEFT
Navigates and changes settings
in the OSD.
Adjusts Horizontal Keystone.
Keystone UP
Navigates and changes settings
in the OSD.
Adjusts Vertical Keystone.
ENTER
Enters and conrms settings in the OSD.
POWER
Turns the projector on and o󰀨.
SOURCE
Opens the Source menu.
Keystone DOWN
Navigates and changes settings in the OSD.
Adjusts Vertical Keystone.
Keystone RIGHT
Navigates and changes settings in the OSD.
Adjusts Horizontal Keystone.
AUTO
Optimizes image size, position and resolution.
Projector indicators
1Filter LED
Displays lter status.
2Temp LED
Displays thermal status.
3Lamp LED
Displays lamp status.
Power LED
Displays power on/o󰀨 sequence status.
13
24
4