i3 i3PROJECTOR Parts list manual

i3PROJECTOR
INTERACTIVE FUNCTIONS MANUAL

Optical touch control projector packing list........................................................................................i
Accessories ................................................................................................................................................ii
Install in Windows OS ............................................................................................................................. 1
Install in Mac OS ....................................................................................................................................20
Install in Linux OS ..................................................................................................................................28
Troubleshooting.....................................................................................................................................30

i
OPTICAL TOUCH CONTROL PROJECTOR PACKING LIST
i3PROJECTOR Interactive functions manual
Accessory check list
Please check this list against accessories included with your optical touch control projector. Please call the
dealer where you purchased the product for any missing item.
1. Light pen 2. Battery (AAA)

ii
ACCESSORIES
Keys and buttons for the light pen
Touch control pen tip
FrontRear
Power switch
How to use (your light pen)?
Press the touch control pen tip to the screen, signals transmitted
from the tip to validate locations with sensors in projector.The touch
control pen tip lights up when sending signals.
1) Place the pen tip anywhere on the screen.
2) Press the pen tip to the screen to activate.You may draw lines in
paint brush mode.
Note:
The sensor on the pen tip consumes power when the tip touches
anything. Please power off the pen when not in use. Touch the pen
tip and see if there is light emitting to make sure.
Before using the light pen
Make sure it is powered on.

1
INSTALL IN WINDOWS OS
i3PROJECTOR Interactive functions manual
The LightPen software features an optical touch control function
1. System requirements
For normal optical touch control operation, please make sure the following
system requirements are met.
Install the LightPen software
System requirements
Operating system Microsoft Windows XP (SP2) (32bit)/Vista (32bit)/Windows 7 (32bit/64bit)
CPU Intel® Core™ 2 Duo 2.0 GHz or better (dedicated GPU is recommended)
Memory 2 GB or more
Minimum hard disk space 100 MB

2
INSTALL IN WINDOWS OS
2. Software installation
2.1 Driver installation
<Install from the USB device>
A CD drive is created by connecting the interaction module to a computer through a USB cable (see
Figure 1). Enter the windows\Setup.exe folder of the CD drive to install SPDriver. You may execute the
launcher.exe program to start the SPDriver directly.
Figure 1 Figure 2
<Install from CD>
Step 1: Insert the Owner's Manual CD into your CD drive.
Step 2: Enter the "LightPen Software for Windows" folder found on your CD.
Step 3: Double click the "Setup.exe" and a pop-up window as shown below will display.

3
INSTALL IN WINDOWS OS - SPDRIVER
i3PROJECTOR Interactive functions manual
Step 4:
(1) Click SPDriver and a pop-up window as shown below will display.Click Next to continue.
(2) Select the destination folder for installation (a default folder is provided). Click Next to
continue.
(3) Please wait until the installation process is completed successfully.

4
INSTALL IN WINDOWS OS - LIGHTPEN3
2.2 Install the LightPen 3 software
Step 1: Insert the Owner's Manual CD into your CD drive.
Step 2: Enter the "LightPen Software for Windows" folder found on your CD.
Step 3: Double click the Setup.exe file name and a pop-up window as shown below will display.
Step 4:
(1) Click LightPen3 and a pop-up window as shown below will display.Click Next to continue.

5
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
(2) Select the destination folder for installation (a default folder is provided).
Click Next to continue.
(3) Click Install after validating the installation data, continue the installation process.
(4) Please wait until the installation process is completed successfully.

6
INSTALL IN WINDOWS OS - LIGHTPEN3
3. Initialize the optical touch control function
3.1 Once the SPDriver is installed, run it by steps Start/All Programs/LightPen/SPDriver/
SPDriver, then connect your projector and a PC with a USB cable.
Your system may look like the Figure shown below.
(Windows 7/VISTA)
(Win XP)
3.2 Click the icon and the menu as shown below will display.
(VISTA/Win XP)
* For Windows XP and Windows Vista, only the standard Mouse Mode is available
* Select "About" to show the software version information.

7
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
(Windows 7)
* The Microsoft Windows 7 OS support multi-point touch control. When using your projector with a PC
running Microsoft Windows 7 OS, you may select to use the default Mouse mode or the Multi-point
Touch Control mode.
* Select "About" to show the software version information.
3.3
(1) Select Calibration to execute the calibration procedure
The system saves calibration data after the four calibration points are touched. Please wait while
system is saving data.

8
INSTALL IN WINDOWS OS - LIGHTPEN3
(2) Auto calibration
You may select Auto Calibration to calibrate your product as prompted by the screens shown in Figure 3.
DO NOT block images shown in the calibration screen while auto calibration is running.
Figure 3
Figure 4
3.4 Calibration completed successfully.
3.5 Auto calibrating failed
Figure 5
If the "auto calibrating failed" message prompts as shown in Figure 5, please take the steps below for
troubleshooting, then do auto calibration again.
1. Turn lights off or reduce stray light to calibration screen
2. Do not walk in front of or shake lens during calibrating
3. Adjust focus to sharpen the images

9
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
3.6 How to execute the driver again
You may execute the driver again by running the steps "Start/All Programs/LightPen/SPDriver".
4. Toolbar
4.1 LightPen3 software toolbar
After the LightPen3 program is installed and "Start/All Programs/LightPen/LightPen3" executed, a
toolbar will display on the right hand side of your screen (see figure).
* Press LightPen icon and select "About" to show the software version information.

10
TOOLBAR - LIGHTPEN3
4.2 Main functions
Icons Names Descriptions
Mouse Mouse functions.
Red brush pen Red brush pen.
Green brush pen Green brush pen.
Blue brush pen Blue brush pen.
Mark pen Translucent brush pen.
Drawing tools To draw circles, rectangles, isosceles triangles,
and lines.
Width and color of
brush pen Select width and color of brush pen.
Eraser Erase strokes made by brush pen.
Clear all Erase all strokes made by brush pen.
Save Save contents and hand drawings of current
page.
Dual pen tool
Select Full Screen Dual Pen or Divided Screen
Dual Pen mode for two parties to write at the
same time.
Whiteboard mode Switch to whiteboard background mode.
Previous page Back to previous page.
Next Go to next page.
Editor Handwriting editor.
On screen keypad Open the on screen keypad.
Exit Exit application software.

11
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
4.3 Sub-functions
(1) Drawing tools
Click and a popup sub-menu from the main menu is shown as below. Click to select the
desired drawing tool for hand drawing.
(2) Dual pen tools
Click and a popup sub-menu from the main menu is shown as below. Click to select the
desired drawing mode for hand drawing.
Icons Descriptions
Both parties make drawings with the same tool in full
screen mode.
Both parties make drawings with the same or different
tools in equally divided screen mode.

12
INSTALL IN WINDOWS OS - LIGHTPEN3
(2.1) Full Screen Dual Pens
Both parties make drawings with the same tool in full screen mode.
Divided Screen Dual Pen
Both parties make drawings with the same or different tools in equally divided screen mode.

13
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
(2.2) Toolbar
Icons Names Descriptions
Red brush pen Red brush pen.
Green brush pen Green brush pen.
Blue brush pen Blue brush pen.
White brush pen White brush pen.
Thin circular stroke Thin brush pen.
Thick circular stroke Thick brush pen.
Square stroke Rectangle brush pen.
Eraser
Erase strokes made by brush pen.
* Only one eraser is available in full screen dual
pen at the same time.
Clear all Erase all strokes made by brush pen.
Import background Load custom background.
Save Save contents and hand drawings of current
page.
Exit Exit dual pen mode.

14
INSTALL IN WINDOWS OS - LIGHTPEN3
(3) Whiteboard mode
Click , the screen will change to whiteboard background and the two
functions on the tool bar would change to Import Background and Import
Whiteboard.
i. Click and the selection window will display for you to import desired pictures as
background. See figure below.
ii Click to restore the background to whiteboard mode.
Click again to exit the whiteboard mode.

15
INSTALL IN WINDOWS OS - LIGHTPEN3
i3PROJECTOR Interactive functions manual
(4) Editing tools
Click and a popup sub-menu from the main menu is shown as below. Click to select the
desired edit function.
Icons Descriptions
Print current screen.
Undo last action.
Cancel undoing last action.
Simulate spotlight effects.
Simulate curtain effects.
Switch toolbar from vertical to horizontal orientation.
Toggle switch location of toolbar at left or right side of the
screen.
4.4 How to use the interaction function
You can use the light pen as a mouse in mouse mode.
Pressing the light pen tip functions like clicking the mouse key.
Pressing and holding the light pen for 2-3 seconds functions the same as right clicking your mouse.
See Figure below.

16
INSTALL IN WINDOWS OS - LIGHTPEN3
4.5 Change toolbar direction
Point the light pen at any place under the projection image and press the pen tip to switch vertical
toolbar into horizontal one.
Point the light pen to the left or right of the projection image and press the pen tip to switch
horizontal toolbar into vertical one.