Delta Children Little Folks LF701406 User manual

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
INSTRUCTION MANUAL
ASSEMBLY INSTRUCTIONS
Styles and colors may vary
LF701406
www.DeltaChildren.com I Customer Service: [phone]
REQUIRED: Phillips Screwdriver (not included)
IMPORTANT: Read all instructions before assembly and use of the product. Keep the
instructions for future reference.
WARNING:
Adult assembly required because of
small parts. Keep assembly parts
out
of reach of children under 3 years.
CHOKING HAZARD
SILENT AUTO GLIDING
BASSINET
DCP-IM-11222019-F3

2
Customer Service Tel. [phone] www.DeltaChildren.com
Consumer Information
WARNING
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised
by your physician.
SUFFOCATION HAZARD
Infants have suffocated:
• In gaps between an extra padding, a mattress (too small or too thick) and
product sides.
• On soft bedding.
• NEVER add a pillow, comforter or another mattress for padding.
• Use only the pad provided by the manufacturer that is no thicker than 25 mm
(1 In) and is of such a size that, when pushed against any side of the product,
it does not leave a gap of more than 25 mm (1 in) between the mattress
and sides.
FALL HAZARD: To help prevent falls, DO NOT use this product when the infant begins to push up on hands and knees or
has reached manufacturer’s recommended maximum weight of 13.6kg (30lbs), whichever comes first.
WARNING: Do not use this bassinet if you cannot exactly follow the accompanying instructions. Failure to follow these
warnings and instructions could result in serious injury or death.
• Read all instructions before assembling unit.
KEEP INSTRUCTIONS FOR FUTURE USE.
DO NOT USE THIS UNIT IF THE INSTRUCTIONS CANNOT BE STRICTLY FOLLOWED.
• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or sharp edges. NEVER use this
product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and
periodically during use. Contact Simmons Customer Service Department at 1-646-435-8726 for
replacement parts, repair or instructions.
• Do not leave child unattended in the bassinet when it is in the “rocking/gliding” mode. Always make sure the wheels or stands are
in the locked “down” position. Remove any tools or excess parts including plastic packaging from bassinet vicinity after assembly.
STRANGULATION HAZARD: Children have STRANGLED in cords. Keep the cord out of reach of children.
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as hood strings or pacifier cords.
DO NOT suspend strings over a product or attach strings to toys.
• Always attach all provided fasteners tightly according to the instructions. Check frequently. Do not use if there are any loose or
missing parts or signs of damage. Do not substitute parts. Contact the manufacturer for replacement parts.
• Use bassinet with only one child at a time.
• Toys are not to be “mouthed” by the baby and should be positioned clearly out of reach of the baby’s face and mouth.
• Do not place medication, small toys, small items, cords, straps or similar items that could become wound around the child’s neck
in or near this product and do not place product near a window, patio door, heater, or power outlet.
•If a sheet is used with the pad, use only the one provided by Delta Children or one specifically designed to fit the dimension of the
bassinet mattress.

3
Customer Service Tel. [phone] www.DeltaChildren.com
STOP
EXTENDED WARRANTY
DON’T MISS YOUR CHANCE TO BE COVERED FOR ALL OF LIFES MISHAPS!
With Delta’s Extended Warranty, you’re covered for mechanical failure from normal use or if
your item stops working due to normal wear and tear, plus all those unexpected surprises.
2 YEARS OF PROTECTION
For Additional Information:
Simply visit our Website, register your product, and add the Extended Warranty
https://www.deltachildren.com/pages/product-registration
Extended Warranty only available in the following States: Arkansas, Colorado, Delaware, District of Columbia, Georgia, Idaho,
Illinois, Indiana, Iowa, Kansas, Kentucky, Louisiana, Maryland, Michigan, Mississippi, Missouri, Nebraska, Nevada, New Hampshire,
New York, North Carolina, North Dakota, Pennsylvania, Rhode Island, South Dakota, Tennessee, Utah, West Virginia
www.DeltaChildren.com • [email protected]
©2019 Delta Children’s Products, Inc. New York, NY 10001
Please DO NOT return this product to the store.
If you experience any difficulty with assembly, missing parts or use, please
DO NOT return this item to the store. Retail stores are unable to properly
assist you. Contact our Customer Service Department directly for assistance
[phone]

4
Customer Service Tel. [phone] www.DeltaChildren.com
Frame
Support Tubes (X2)
Mattress Support Board
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Fabric Storage Liner
Auto-Glide Housing (X1)
(Needs 2 - M6 - 3.5cm - screws to attach
to front base leg with wire connection)
Mattress Pad
Sheet
Fabric Liner
BOTTOM
TOP
Base Leg with Wire
Connection (X1)
(For auto glide and
power cord attachment)
FrontBack
Base Leg (X1)
FRONT
FRONT

5
Customer Service Tel. [phone] www.DeltaChildren.com
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Phillips Screwdriver
(NOT INCLUDED)
Hardware
*Screws are shown in actual size - 10 total screws
Music Module
WIRE 2
Top Front Base Leg
LARGE PLUG
WIRE 1
Auto Glide
SMALL PLUG
Locking Casters (X2)
Canopy
Power Cord
M6 - 1.7cm x 8pcs
M6 - 3.5cm x 2pcs
(Used for power housing assembly)

6
Customer Service Tel. [phone] www.DeltaChildren.com
Top Frame Assembly
1
NOTE: You may need the help of another adult for assembly.
*Completed top frame assembly
NOTE: Make sure front of frame is aligned with top front
mattress support
• Place the frame on a flat surface and extend the support
legs out.
• Locate the mattress support board and align the front of frame
to top of support board front.
• Align and insert the (4) support legs into the (4) support board
housings until they “click” in place.
NOTE: Pull upward to make sure support legs are fully locked.
Support Legs
Support Legs
FRAME
MATTRESS
SUPPORT
BOARD
FRONT
“CLICK”
TOP
FRONT
FRAME
TOP
FRONT
3
1
2
3
TOP
FRONT
FRONT

7
Customer Service Tel. [phone] www.DeltaChildren.com
Attaching Power Housing to Front Base Leg
1M6 Screw - 3.5cm - x2 - Actual Size
THIS SIDE UP
FACING INWARD
Auto-Glide Housing
M6 Screw
Thread
Auto-Glide
Housing Nub
M6 Screw
Thread
Auto-Glide
Housing
• Locate the auto-glide housing, front base leg with power connection,
two (x2) M6 x 3.5cm screws and a Phillips screwdriver.
• Align the auto-glide housing nub post to the center hole inside the
base leg.
• Next using a Phillips screwdriver, tighten two (x2) M6 screws on
the opposite sides of the base leg.
• Pull outward on the auto-glide housing to make sure it is securely
attached.
Attach (x2) M6 Screws
FACING
INSIDE
Auto-Glide Housing fully
attached to front base leg
Front Base
Leg
Auto-Glide
Housing Front Base
Leg

8
Customer Service Tel. [phone] www.DeltaChildren.com
Front Base Leg and Frame Assembly
1M6 Screw - 1.7cm - x2 - Actual Size
• Locate the two (x2) M6 screw, a Phillips screwdriver, and the
front base leg.
• Insert the two (x2) M6 screw to the assembled front base leg
and use the Phillips screwdriver to tighten on both sides.
NOTE: Align the front base leg so that the power housing is facing
inside of the bassinet.
BOTTOM
&
FRONT
TOP
FRONT
FRAME
FRONT
BASE LEG
MATTRESS
SUPPORT BOARD
BOTTO M
&
F RONT

9
Customer Service Tel. [phone] www.DeltaChildren.com
Back Base Leg and Frame Assembly
1M6 Screw - 1.7cm - x2 - Actual Size
• Locate the two (x2) M6 screw, a Phillips screwdriver, and the
back base leg.
• Insert the two (x2) M6 screw to the back base leg
and use the Phillips screwdriver to tighten on both sides.
Align two side nubs
to the three holes on frame
FRAME
BACK
BACK
BASE LEG
MATTRESS
SUPPORT BOARD
BACK
BASE LEG
TOP
FRONT
NOTE: You may need the help of another adult for assembly.

10
Customer Service Tel. [phone] www.DeltaChildren.com
Storage Area Assembly
1
3
Slide Support Tube Into
Fabric Storage Liner
Fabric Storage Liner
Support Tube
Fabric Storage Liner
Facing Upward
• Locate the two (x2) support tubes, and the fabric storage liner.
• Slide the support tubes into fabric storage liner on both sides.
• Flip over the fabric storage liner with support tubes, facing
upward.
Fabric Storage Hole
Corner
1
2
2
Align storage basket to
bottom base legs.
Insert each end of the
support tubes to the entry
hole of the base legs.
1 2
M6 Screw - 1.7cm - x2 - Actual Size
• Locate the four (x4) M6 x 1.7cm screws and a Phillips screwdriver
• Insert the (x4) M6 screws on both sides of the legs and use a
Phillips screwdriver to tighten both screws on both sides.
FRONT
FRONT
FRONT
FRONT
NOTE: Pull side support tube to make sure it’s fully fastened.

11
Customer Service Tel. [phone] www.DeltaChildren.com
Locking Casters Assembly
1
.
2
• Locate the two (x2) locking casters and insert into the bottom
leg joints of the front base leg.
• Insert the casters into the base legs. Push down until you hear
the caster “CLICK” into place.
• Pull upward on the caster to assure it is properly attached to the
bassinet.
*Once casters are assembled, turn the assembly
bassinet upright.
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT

12
Customer Service Tel. [phone] www.DeltaChildren.com
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
CAUTION - Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device.
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.
Consumer Information
WARNING

13
Customer Service Tel. [phone] www.DeltaChildren.com
AUTO
GLIDE
• To attach Music Module, remove the screws and line up music module
to screw holes on front frame.
• Position Music Module onto front of frame and screw module to frame.
Attaching Music Module
2
1
WIRE 2
Top Front Base Leg
LARGE PLUG
WIRE 1
Auto Glide
SMALL PLUG
Music Module Operation
• Press Auto Glide button (AUTO
GLIDE) to start 15
minute cycle of auto glide.
• Press again to stop auto glide.
• Activate bassinet light by pressing LIGHT
button
on the top of the music module.
NOTE: Light will stay on in 10-minute cycles, unless
button is pressed before 10 minutes are up.
• Press MUSIC button ( ) on top of the music
module to activate MUSIC. Press button multiple
times to cycle through three (3) music melodies.
• Volume can be adjusted with UP/DOWN
buttons on the top of the music module.
Auto
Glide
Light
Music
AUTO
GLIDE
Volume
DOWN
Volume
UP

14
Customer Service Tel. [phone] www.DeltaChildren.com
Snaps
Pocket
Mattress
Support
Attaching Fabric
13
• Locate the fabric liner.
NOTE: Front of the frame has the music module and the front of
the liner has the warning label.
• Align the fabric hole over the music module.
• Place the liner onto the frame. Make sure warning is centered
at the front of the bassinet.
Music Module
FRONT
2
• Stretch the pockets on the bottom of the liner around the
ends of the mattress support.
• Lift the skirt on the liner, snap all (8) of the straps around the
top tube of the frame and all (4) snaps to the underside of the
mattress boards.
.
Mattress Pad With Sheet
4
• Place the sheet over the mattress pad.
• Place the covered mattress pad into the liner.
Hook and
Loop Patch
Canopy Ratchet
Frame
5
• Position the canopy over the top end of the bassinet opposite the
warning label.
• Push aside foam to expose metal and push the canopy ratchet onto
the frame on both sides of the bassinet.
• Fasten the hook and loop fasteners on the back edge of the canopy
to the liner. Then fasten the hook and loop patches on each canopy
flap to the side of the liner.
Music Module

15
Customer Service Tel. [phone] www.DeltaChildren.com
Wire Connection Assembly
1
• Lift the fabric on the front of the bassinet.
• Locate the auto-glide housing plug cord and insert it into the
auto-glide connector . (Fig. 1)
• Locate the large plug cord and insert into the top leg
connector . (Fig. 2)
Make sure both wires are fully connected (Fig. 1)
1
1
2
2
1
1
2
2
WIRE 1
Auto Glide
SMALL PLUG
WIRE 2
Top Front Base Leg
LARGE PLUG
1
2
1
1
1
2
2
Fig. 1
Fig. 1A
1
1
1
1
1
2
2
WIRE 1
Auto Glide
SMALL PLUG
WIRE 2
Top Front Base Leg
LARGE PLUG
2
Fig.
1

16
Customer Service Tel. [phone] www.DeltaChildren.com
Wire Connection Assembly
2
Bottom Base Leg Connection
Located On The Inside Of Base Leg
Fig. 4
Fig. 3
• Locate the Power Cord. Insert underneath the fabric storage
liner opening and plug into the Bottom Base Leg Connector
(Fig. 2) until fully connected (Fig. 2A)
Fig. 2
Fig. 2A

17
Customer Service Tel. [phone] www.DeltaChildren.com
Care and Maintenance
• The frame, mattress pad, storage area, music module may be wiped clean using a mild cleaning solution and
a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove
residue. Do not immerse the frame.
• The sheet is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• Always store product in a clean and dry place.
• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or sharp
edges. NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or
torn mesh/fabric. Check before assembly and periodically during use. Contact Simmons Customer Service
Department at 1-646-435-8726 for replacement parts, repair or instructions.

18
Customer Service Tel. [phone] www.DeltaChildren.com

19
Customer Service Tel. [phone] www.DeltaChildren.com

www.DeltaChildren.com
1-646-435-8726