Delta Children Little Folks SleepCool LF20353 User manual
INSTRUCTION MANUAL
Customer Experience Center
www.DeltaChildren.com
STYLES AND COLORS MAY VARY
WARNING:
Adult assembly required because of
small parts. Keep assembly parts
out
of reach of children under 3 years.
CHOKING HAZARD
Read all instructions BEFORE assembly and USE of product
KEEP INSTRUCTIONS FOR FUTURE USE.
LF20353
ADULT ASSEMBLY REQUIRED
SleepCool
Rocking Bassinet
with Airflow Mesh
2
Consumer Information
WARNING
WARNING: Do not use this bassinet if you cannot exactly follow the accompanying instructions. Failure to follow these
warnings and instructions could result in serious injury or death.
• Read all instructions before assembling unit.
KEEP INSTRUCTIONS FOR FUTURE USE.
DO NOT USE THIS UNIT IF THE INSTRUCTIONS CANNOT BE STRICTLY FOLLOWED.
• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or sharp edges.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric.
Check before assembly and periodically during use. Contact Delta Children Customer Service Department at
SUFFOCATION HAZARD: Infants have suffocated:
• On soft bedding.
• In gaps between an extra padding, a mattress (too small or too thick) and product sides.
• Use only the pad provided by the manufacturer that is no thicker than 25 mm (1 In) and is of such a size that, when
pushed against any side of the product,it does not leave a gap of more than 25 mm (1 in) between the mattress and
sides.
• NEVER add a pillow, comforter or another mattress for padding.
•Remove any tools or excess parts including plastic packaging from bassinet vicinity after assembly.
• If a sheet is used with the pad, use only the one provided by the manufacturer or one specifically designed to fit the
dimensions of the bassinet/cradle.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep,
unless otherwise advised by your physician.
• Never use plastic shipping bags or other plastic film as a mattress covers not sold and intended for
that purpose. They can cause suffocation.
•DO NOT place bassinet near a window where cords from blinds or drapes may strangle a child.
Child may fall out of window.
•DO NOT place cords, straps or similar items that could become wound around a child’s neck in or
near the bassinet.
FALL HAZARD: To help prevent falls, DO NOT use this product when the infant begins to push up on hands and
knees or has reached manufacturer’s recommended maximum weight of 13.6kg (30lbs), whichever comes first.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
• Always attach all provided fasteners tightly according to the instructions. Check frequently. Do not use if there are any
loose or missing parts or signs of damage. Do not substitute parts. Contact the manufacturer for replacement parts.
• Use bassinet with only one child at a time.
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a product or attach strings to toys.
• Toys are not to be “mouthed” by the baby and should be positioned clearly out of reach of the baby’s face and mouth.
•DO NOT place medication, small toys, small items, cords, straps or similar items that could become wound around
the child’s neck in or near this product and do not place product near a window, patio door, heater, or power outlet.
3
Before returning this product to the store!
Let’s see if we can assist you!
• Not sure how to assemble our product?
Visit our site for easy to follow instructions along with some Tricks and Tips assembly video’s
https://www.deltachildren.com/pages/instructions
• If you are missing a piece or have a damaged part
To better assist you please have your Style #, Lot # and Manufacturer Date information available
along with the part number that you need assistance with.
• In the event we do not have a replacement part available
You may need to return your product to the retailer for an exchange or refund.
• Warranty
In order to protect your investment, don’t forget to register your product.
You may also wish to consider purchasing our extended warranty.
Visit https://www.deltachildren.com/pages/extended-warranty for more details.
• Please note:
“All Final”, “As Is” or Third Party/Liquidator sales are not covered under our Limited Manufacturer
Warranty..
4
LIMITED MANUFACTURER WARRANTY
This Delta product is warranted to be free from defects for a period of 90 days from the
date of purchase under normal use. This warranty extends only to the original retail
purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the
registration is on file with Delta. This limited manufacturer warranty does not cover the following:
• Products purchased as floor models or samples.
• Items purchased on an “as-is” basis, as a second hand product, or as a resale product.
• Items purchased at a Final sale, a “Going out of Business” sale, or a Liquidation sale.
TO REGISTER YOUR PRODUCT for important safety alerts and updates to your product please
visit www.deltachildren.com
TO REPORT A PROBLEM, please log on to www.deltachildren.com and click the Consumer
Date of Purchase: _____________ (you should also keep your receipt)
DON’T MISS YOUR CHANCE TO BE COVERED FOR ALL OF LIFES MISHAPS!
With Delta’s Extended Warranty, you’re covered for mechanical failure from normal use or if your item
stops working due to normal wear and tear, plus all those unexpected surprises.
2 YEARS OF PROTECTION
For Additional Information:
Simply visit our Website, register your product, and add the Extended Warranty
https://www.deltachildren.com/pages/product-registration
Extended Warranty only available in the following States: Arkansas, Colorado, Delaware, District of Columbia, Georgia, Idaho, Illinois, Indiana,
Iowa, Kansas, Kentucky, Louisiana, Maryland, Michigan, Mississippi, Missouri, Nebraska, Nevada, New Hampshire, New York, North Carolina,
North Dakota, Pennsylvania, Rhode Island, South Dakota, Tennessee, Utah, West Virginia
EXTENDED WARRANTY
5
PARTS
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Fabric Liner Frame
Legs (X2)
Base (X2)
Cross Tubes (X2)
Mattress Sheet
Mattress Pad
Mattress Support
Storage Basket
Music Module
M6 (4 CM) Hex Screw (X8)
*Screw is actual size to scale
M6 Lock Nut (X4) Wrench
Screw Driver
*Lock Nut is actual size to scale
M5 (2.6 CM) Hex Screw (X2)
*Screw is actual size to scale
M5 Lock Nut (X2)
*Lock Nut is actual size to scale
Mobile Arm &
Toys
M4 (2.5cm) (X2)
*Screw is actual size to scale
M5 (2.1cm) (X2)
6
Bassinet Frame Assembly
NOTE: You may need the help of another adult to help steady all parts for
assembly.
• Place a base on a flat surface with the slots facing up.
• Fit a cross tube into each slot. Push down on each tube to be sure it
is in place (Fig. 1)
• Position the storage basket so that the pockets face away from you.
• Slide the storage basket fabric sleeves onto the cross tubes (Fig. 2).
1
2
Cross Tubes
Sleeves
Storage
Basket
Base
Slots
Fig. 1
Fig. 2
7
• Fit the other base slots onto the cross tubes (Fig. 3).
• Push on the base near each cross tube to be sure it is in place. • Insert four (M6 x 4 cm) screw through the hole in each base, the ends
of the legs and into the end of each cross tube (Fig. 5).
Hint: You may need to align the holes of all three parts to properly insert
the screw.
• Tighten the screw with the Phillips screwdriver.
• Repeat this procedure to fasten the legs, bases and cross tubes on the
other side of the assembly.
• First, fit the ends of a leg into short fabric sleeves in the storage basket.
Then, fit the ends of the leg into receptacle in each base (Fig. 4).
• Repeat this procedure to assemble the other leg to the storage basket
and bases.
3
4
5
Bassinet Frame Assembly
Base
Leg
M6 (4 CM) Hex Screw (X4)
*Screw is actual size to scale
Fig. 3
Fig. 4
Fig. 5
8
• Turn the assembly upright (Fig. 6).
• Check to be sure the legs are secure. While gently holding the base
down, pull up on the legs. They should remain assembled to the bases.
• Rotate the bases of the frame down.
• Place the frame onto the top of the legs. Align the holes in the bases of
the frame with the holes in the legs (Fig. 7)
NOTE: Do not remove the foam around top of frame.
• Insert four M6 x 4cm screws through the holes in the frame and legs
(Fig. 8).
• Attach an M6 lock nut to the end of each screw. Make sure the rounded
side of the lock nuts face down. Hand-tighten the lock nuts onto the
screws (Fig. 9).
6
7
8
9
Bassinet Frame Assembly
M6 Lock Nut (X4)
*Lock Nut is actual size to scale
M6 (4 CM) Hex Screw (X4)
*Screw is actual size to scale
Fig. 6
Fig. 7
Fig. 9
Fig. 8
9
• While holding an M6 lock nut in place with the wrench, completely
tighten a screw with the Phillips screwdriver (Fig. 10).
• Repeat this procedure tighten the other three screws.
• Check to be sure the frame is secure. While gently holding a base
own, pull up on the frame It should remain attached to the legs (Fig. 11).
• Place the mattress support into the frame (Fig. 12).
• Align the holes in the mattress support with the holes in the frame.
• Insert two (M5 x 2.6 cm) screws through the mattress support and into
the frame (Fig. 13).
10
11
12
13
Bassinet Frame Assembly
M5 (2.6 CM) Hex Screw (X2)
*Screw is actual size to scale
Fig. 10
Fig. 1
Fig. 12
Fig. 13
10
• Attach a M5 lock nut to the end of the screw. Make sure the
rounded side of the lock nut faces down. Hand-tighten the lock
nuts onto the screws (Fig. 14).
• While holding an M5 lock nut in place with a wrench, completely
tighten screw with a Phillips screwdriver (Fig. 15).
• Repeat this procedure to tighten the other screws.
14
15
Bassinet Frame Assembly
M5 Lock Nut (X2)
*Lock Nut is actual size to scale
Fig. 14
Fig. 15
11
FRONT
REAR
Attaching Mobile Arm & Fabric Liner
Fig. 1
• Locate the two (x2) M5 x 2.1cm screws and a Phillips screwdriver
(Fig. 2).
• Align the two holes of the mobile arm joint to the top rail holes and Insert
the (x2) M5 screws onto the mobile arm joint and use a phillips screw
driver to tighten both screws on both sides (Fig. 2A).
• Position mobile arm near the rear of the bassinet and align the two holes
on the mobile arm oint to the top rail holes (Fig. 1).
• Locate mobile arm hole on rear of fabric liner and insert it over the
mobile arm (Fig. 3).
ATTACHING TOYS TO MOBILE ARM
• Locate the mobile arm and toys and attach it together until it locks in
place (Fig.4 ).
13
24
M4 (2.5cm) (X2)
*Screw is actual size to scale
FRONT
REAR
FRONT
Fig. 2
Fig. 3
Fig. 4
M5 (2.1cm) (X2)
12
4
2
3
1
Fabric Liner & Mattress Pad Assembly
• Stretch the pockets bottom of the liner around the ends of the mattres
support.
• Snap all 2 snaps to the bottom of mattress board (Fig. 1).
• Repeat this procedure to snap the other 2 snaps around the bottom
of mattress board.
• Lift the skirt on the liner. Snap all 4 straps around the top of the side of
the frame (Fig. 3).
• Repeat this procedure to snap the other 4 straps around the top of the
frame.
• Place the sheet over the mattress pad (Fig. 4)
• Please place the mattress pad with sheet inside the bassinet for the
safety and comfort of your baby (Fig. 5).
Mattress Pad
with Sheet
Pocket
Snaps
Snaps
Fig. 1
Fig. 3
Fig. 4
Fig. 5
13
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
CAUTION: - Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.
Consumer Information
14
Attaching Music Module
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid battery
leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
• When discarding batteries, be sure to dispose of them in the proper
manner, according to your state and local regulations.
Battery Safety Information
(4)
four
1. 2.
15
Music Module Operation
(5 minute) (5 minute)
3.
Attaching Music Module
Volume UP
Music
Light
Vibration
Volume DOWN
Vibration
Vibration
16
Retractable Wheels
Bassinet Mode
• Turn the wheel lock to lower the wheel. Make sure you hear a “click”
as the wheel locks in place (Fig. 1).
• Repeat this procedure to lower the other three wheels.
Rocking Mode
• First, pull the wheel down (Fig. 2).
• Then push it up into the base (Fig. 2A).
• Make sure lock tab is facing up as wheel is inserted into base.
• Repeat this procedure to retract the other three wheels.
2
1
Wheel Lock
Fig. 1 Fig. 2
Fig. 2A
Care and Maintenance
• The frame, mattress pad, and storage basket may be wiped clean using a mild cleaning solution and a damp cloth. Do not
use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Do not immerse the frame.
• The sheet is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Tumble dry
separately on low heat and remove promptly.
• Always store product in a clean and dry place.
• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or sharp edges. NEVER
use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before
assembly and periodically during use. Contact Delta Children Customer Service Department at [email protected] for
replacement parts, repair or instructions.
© 2020 Delta Children's Products. All rights reserved.
Delta Children's Products Corp.
114 West 26th Street
New York, NY 10001
www.DeltaChildren.com
This manual suits for next models
1
Table of contents
Other Delta Children Baby & Toddler Furniture manuals
Delta Children
Delta Children Crib N Changer User manual
Delta Children
Delta Children 81529-251 User manual
Delta Children
Delta Children Classic User manual
Delta Children
Delta Children baby GAP 4 in 1 Crib User manual
Delta Children
Delta Children SIMMONS KIDS 27203 Series User manual
Delta Children
Delta Children Foundry W343150-1395 User manual
Delta Children
Delta Children N Changer User manual
Delta Children
Delta Children CLASSIC DELUXE WOOD BASSINET 25573 User manual
Delta Children
Delta Children Simmons Juvenile Crib 'N' More User manual
Delta Children
Delta Children Changing Table 7517 User manual
Delta Children
Delta Children Jeep Safety Gate User manual
Delta Children
Delta Children Huck W146010-130 User manual
Delta Children
Delta Children Madeline W134040-130 User manual
Delta Children
Delta Children Crib 'N' More User manual
Delta Children
Delta Children Toddler Sleep Play Area User manual
Delta Children
Delta Children Eclipse User manual
Delta Children
Delta Children KID SIZE 55100 User manual
Delta Children
Delta Children Arch Trundle User manual
Delta Children
Delta Children LX DELUXE 26201 User manual
Delta Children
Delta Children SIMMONS KIDS By The Bed Deluxe Bassinet User manual
Popular Baby & Toddler Furniture manuals by other brands
Monbebe
Monbebe BCY102 user guide
Crate&Barrel
Crate&Barrel Archway Toddler Rail Assembly instructions
Woodward
Woodward 8909-051 Installation and operation manual
Carena
Carena INGARO quick start guide
Mocka
Mocka Teneriffe Assembly instructions
caramia furniture
caramia furniture BLAIR CRIB 3-1 CONVERTIBLE Assembly instructions
