Delta Children 7584 User manual

Style #:
Lot:
Date:
___________
___________
___________
©2011 DELTA ENTERPRISE CORP.
A
Changing Table
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Top Shelf.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
DECEMBER 30, 2011, 22811, R0
Conforms to
ASTM F2388
Safety Standards

2
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
Always secure the pad to the changing surface by inserting the strap through the hole in
the middle of the pad. See Instructions.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
3
H. Top Shelf x 1
J. Bottom Shelf x 2
K. Foam Pad x 1
C. Cap Rail x 2
D. Upper Back Rail x 1
E. Top Front Rail x 1
F. Front Middle Rail x 1
G. Bottom Rail x 4
A. Left Side x 1
B. Right Side x 1
L. Restraint Harness x 1
Part # 22796
Part # 22797
Part # 22798
Part # 22799
Part # 22800
Part # 22801
Part # 22802
Part # 22803
Part # 22804
Part # 22830
Part # 21691
M. Drawer Front x 1
Part # 22805
N. Drawer Back x 1
Part # 22806
P. Drawer Left Side x 1
Part # 22807
R. Drawer Right Side x 1
Part # 22808
S. Drawer Bottom x 1
Part # 22809
T. Drawer Support x 1
Part # 22810
EE. Back Middle Rail x 1
Part # 22931
FF. Back Middle Panel x 1
Part # 22932

:STRAP
4
M4 Allen Wrench Supplied
Z. Φ6x25 mm Wood Dowel x 4
U. M6 x 35 mm Bolt x 20
V. M6 x 20 mm Bolt x 1
Y. 25mm Flat Head WoodScrew x 5
BB. Nut x 1
AA. Nylon Washer x 2
Phillips Screwdriver
Pliers or Adjustable
Wrench Required
for Assembly
(not supplied)
No drills necessary. Do not
use power screwdriver.
HARDWARE KIT PART #22812 FOR COLOR 100 OR #22813 FOR COLOR 604 OR
#22814 FOR COLOR 260. SEE COVER PAGE.
Part # 5464
Part # 5461
Part # 5065
Part # 5525 Part # 4065
Part # 5508
Part # 1177
W. Knob x 2
Part # 22815
X. M4 x 30 mm Bolt x 2
Part # 5606
CC. 35 mm Flat Head Wood Screw x 4
Part # 5517
DD. Plastic Barrel Nut x 4
Part # 5497

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
5
M4 Allen Wrench
Supplied
E
G
U. M6 x 35 mm Bolt x 8
F
D
A. Left Side x 1
D. Upper Back Rail x 1
E. Top Front Rail x 1
F. Front Middle Rail x 1
G. Bottom Rail x 4
A
Attach (1) Upper Back Rail (Part D), (1) Top Front Rail (Part E), (1) Front Middle Rail (Part F), (1) Back
Middle Rail (Part F) and (4) Bottom Rails (Part G) to the Left Side (Part A) with (8) M6 x 35 mm Bolts
(Part U) using the M4 Allen Wrench as shown.
BE SURE THE GROOVES FACE TO THE INSIDE.
G
EE
U
U
U
U
U
U
U
U
EE. Back Middle Rail x 1
EE, Holes to INSIDE
Groove to TOP.

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
6
From Step 1
J
J
H
H. Top Shelf x 1 J. Bottom Shelf x 2
Lay the Left Side on the floor, rails up. Slide the Top Shelf (Part H) in the grooves on the Top Front Rail
and Upper Back Rail, into the groove on the Left Side. Slide (2) Bottom Shelves (Part J) in the grooves
on the Bottom Rails, into the grooves on the Left Side. Slide the Back Middle Panel (Part FF) in the
grooves on the Upper Back Rail and Back Middle Rail to the Left Side as shown.
FF. Back Middle Panel x 1
FF

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
7
From Step 2
M4 Allen Wrench
Supplied
B. Right Side x 1
Attach (1) Right Side (Part B) to the assembly from step 2 with (8) M6 x 35 mm Bolts (Part U) using the
M4 Allen Wrench as shown.
U. M6 x 35 mm Bolt x 8
U
B
U
U
U
U
U
U
U

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
From Step 3
M4 Allen Wrench Supplied
C. Cap Rail x 2
U. M6 x 35 mm Bolt x 4
Attach (2) Cap Rails (Part C) to the assembly from step 3 with (4) M6 x35 mm Bolts (Part U) using the
M4 Allen Wrench as shown.
U
U
U
U
C
C

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
From Step 4
M4 Allen Wrench Supplied
BB. Nut x 1
V. M6 x 20 mm Bolt x 1
Pliers or Adjustable Wrench
(Not Supplied)
L. Restraint Harness x 1
AA. Nylon Washer x 2
Align the hole in the middle of the strap of the Restraint Harness (Part L) with the hole in the Top Shelf.
Insert (1) M6 x 20 mm Bolts (Part V) through a Nylon Washer (Part AA), the restraint strap and the hole
in the shelf. Add (1) Nylon Washer (Part AA) with a Nut (Part BB). Hold the nut with a Pliers or
Adjustable Wrench.
L
AA
BB
AA
V

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
From Step 5
K
1. Insert the strap through the hole in the Foam Pad (Part K).
2. Place Foam Pad (Part K) on Top Shelf (Part H).
K. Foam Pad x 1
Click !
2
1
3