Delta Childrens Products 7664 User manual

Style #:
Lot:
Date:
___________
___________
___________
©2011 DELTA ENTERPRISE CORP.
A
4 in 1 Crib
Conforms to
ASTM F1169-10a Full
Size Crib & F1821
Safety Standards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
NOVEMBER 3, 2011, 22516, R0

WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string
around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or
attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib
has an adjustable mattress support. For the convenience of the parent when the baby is very small, the
mattress support may be used in the highest position. Important: with the mattress support and
mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches
higher then the top surface of the mattress. If it is not, lower the mattress support and the mattress to
the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts,
or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and
other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact Delta
Children's Products for replacement parts and instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that
every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
*In Canada Only - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it
is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or
who is taller than 90 cm.
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL
BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN.

3
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in
thickness. The mattress thickness must not exceed 6 in (150mm).

A. Back Top Rail x 1
F. Right Crib End x 1
J. Stabilizer Bar x 1
4
PRODUCT LABEL
B. Back Rail x 1
E. Left Crib End x 1
Part # 22507
Part # 22508
Part # 22511 Part # 22512
Part # 22510
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
H. Mattress Support x 1
Part # 16945
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED OT THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL
BACK INSIDE BOTTOM LABEL
G. Front Rail x 1
Part # 22509
C. Left Rear Leg x 1
Part # 22513
D. Right Rear Leg x 1
Part # 22514
FRONT INSIDE BOTTOM LABEL

5
R. Φ4x30 mm Metal Pin x 2
HARDWARE KIT PART #22515 FOR COLOR 100 OR #22703 FOR COLOR 255 OR
#22704 FOR COLOR 645. SEE WARRANTY PAGE.
No drills necessary. Do not
use power screwdriver.
PARTS:
Flat Head Screwdrive
(not supplied)
K. M6 x 75 mm Bolt x 4
L. M6 x 65 mm Bolt x 4
M. M6 x 50 mm Bolt x 8
N. M6 x 15 mm Bolt x 4 P. M6 x 17 mm Barrel Nut x 8
M4 Allen Wrench Supplied
Part # 5460
Part # 5467
Part # 5470
Part # 5472
Part # 5479
Part # 5493
Part # 1177

6
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
B
D
SECTION 1: CRIB ASSEMBLY
L
C
P
L
BACK !
L. M6 x 65 mm Bolt x 2
P. M6 x 17 mm
Barrel Nut x 2
M4 Allen Wrench Supplied
Attach (1) Left Rear Leg (Part C) and (1) Right Rear Leg (Part D) to (1) Back Rail (Part B) using
(2) M6x65mm Bolts (Part L) and (2) M6x17mm Barrel Nuts (Part P). Tighten with the M4 Allen Wrench.
Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
C. Left Rear Leg x 1
D. Right Rear Leg x 1
B. Back Rail x 1
BACK INSIDE BOTTOM LABEL
P

7
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Insert the tenon of the Back Top Rail (Part A) into the slot on top of the Back Rail (Part B), then insert the (4) M6x50mm
Bolts (Part M), through the legs into the Metal Inserts on the Back Top Rail (Part A) as shown.
M. M6 x 50 mm Bolt x 4
From Step 1
M
A
B
M
A. Back Top Rail x 1
BACK INSIDE BOTTOM LABEL

8
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
P. M6 x 17 mm Barrel Nut x 4
M4 Allen Wrench Supplied
Attach (1) Left Crib End (Part E) and (1) Right Crib End (Part F) to the assembly from step 2 using (4)
M6x75mm Bolts (Part K) and (4) M6x17mm Barrel Nuts (Part P). Tighten with the M4 Allen Wrench.
Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
From Step 2
E
K. M6 x 75 mm Bolt x 4
F. Right Crib End x 1
PRODUCT LABEL
E. Left Crib End x 1
LEFT INSIDE BOTTOM LABEL
RIGHT INSIDE BOTTOM LABEL
K
P
K
P
P
P
K
KF

9
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
From Step 3
N. M6 x 15 mm Bolt x 4
H. Mattress Support x 1
WARNING:
!
! WARNINGS ON POUCH MUST FACE UP.
H
!
UP
Attach the Mattress Support (Part H) in all corners using (1) M6 x 15 mm Bolt (Part N) in each corner.
Tighten with the M4 Allen Wrench.
The Warnings printed on the pouch attached to the
mattress support must face up, the springs must face up.
This crib has (3) adjustment positions, use the highest only
for new borns, move the mattress down as the child grows.
Fall Hazard: When child is able to pull to a standing position,
set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps
for climbing out.
ALL CORNERS
N

10
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
P. M6 x 17 mm Barrel Nut x 2
M4 Allen Wrench Supplied
Attach the Front Rail (Part G) to the assembly from step 4 using (2) M6x65mm Bolts (Part L) and (2)
M6x17mm Barrel Nuts (Part P). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver to
hold the Barrel Nut in the proper alignment.
From Step 4
G
L. M6 x 65 mm Bolt x 2
FRONT INSIDE BOTTOM LABEL
L
P
P
L
G. Front Rail x 1
PULL GENTLY PULL GENTLY
NOTE: DO NOT FULLY TIGHTEN AT THIS TIME.

11
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 1: CRIB ASSEMBLY
M4 Allen Wrench Supplied
Lay the Back Rail on the floor. Attach (1) Stabilizer Bar (Part J) to the assembly from step 5 using (2)
Φ4x30 mm Metal Pins (Part R) and (4) M6x50mm Bolts (Part M). Tighten all bolts with the M4 Allen
Wrench.
From Step 5
R. Φ4x30 mm Metal Pin x 2
J
PULL GENTLY
J. Stabilizer Bar x 1
M. M6 x 50 mm Bolt x 4
PULL GENTLY
M
R
R
M

SECTION 1: CRIB ASSEMBLY
STEP 7
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
12
ASSEMBLY INSTRUCTION
BOOKLET
WARNING: SEE PAGE 2 FOR INFORMATION
Store the assembly instruction booket in the pouch attached to the mattress support. Store all parts
and tools separately, in a safe place.
Style #:
Lot:
Date:
___________
___________
___________
©2011DELTA ENTERPRISE CORP.
A
Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114 West26th Street
New York,NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Toregister your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Dueto the presence of small parts during assembly, keepout of
reachof children until assembly is complete.
OCTOBER20, 2011, 22516, R0
AI BAG
Style #:
Lot:
Date:
___________
___________
___________
©2011DELTA ENTERPRISE CORP.
A
Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114West 26th Street
NewYork, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Toregister your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULTASSEMBLY REQUIRED
Dueto the presence of small parts during assembly, keep out of
reachof children until assembly is complete.
OCTOBER20, 2011, 22516, R0

13
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
Remove the Front Rail and Stabilizer Bar intalled in Step 5 and 6 of Section 1 crib assembly.
Finished Crib
J
L
PULL GENTLY
PULL GENTLY
M
P
L
P
M
G

14
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
SECTION 2: TODDLER BED CONVERSION
M4 Allen Wrench Supplied
Attach the Stabilizer Bar (Part J) to the assembly from step 1 using (4) M6x50mm Bolts (Part M).
Tighten with the M4 Allen Wrench.
From Step 1
J
M. M6 x 50 mm Bolt x 4
J. Stabilizer Bar x 1
PULL GENTLY
M
PULL GENTLY
M

SECTION 2: TODDLER BED CONVERSION
STEP 3
15
WARNING:
TODDLER BED WARNINGS
SEE PAGE 3 FOR
The mattress support must be in the lowest positions.
Store all hardware safely.
Read all warnings on page 3.
As shown, use as a day bed or love seat sofa.
Do Not use without stabilizer bar intalled.
Stabilizer bar must be used when converted
to a toddler bed.
A toddler bed guardrail is available for this
crib.
Please see your crib retailer, visit
www.DeltaChildren.com or contact delta
consumer care for more information.
This crib uses Delta Style # 0081 Guardrail.

SECTION 3: FULL SIZE BED CONVERSION
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
16
M4 Allen Wrench Supplied
You have the option to convert the crib to a Full Size Bed. Simply follow the steps in reverse order to
disassemble the crib. Stop after removing the Left and Right Crib Ends with the M4 Allen Wrench
as shown.
Store all parts and hardware in a safe place.
K
K
K
K
P
P

SECTION 3: FULL SIZE BED CONVERSION
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
17
From Section 3 Step 1
Attach Bed Frame to the Headboard (From Section 3 Step 1) using (4) M6x15mm Bolts (Part N).
Follow all instructions supplied with the Bed Frame. Note: Bed Frame System is not included, see
you furniture or mattress retailer. Contact Delta Children’s Products for information or with questions.
N. M6 x 15 mm Bolt x 4
M4 Allen Wrench Supplied

Warranty: This Delta Crib is warranted to be free from defects for a period
of 1 year from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Crib End bottom rail.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: 7664 A