DELTA DORE Tydom Home User manual

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC : 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC : 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC : 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC: 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC: 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC : 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée

INFO
APPLICATION
Presentation
Installation
❶ Connect your Tydom Home by
STRICTLY following this order:
①connect the Ethernet cable (B).
②then, connect the mains power (C).
❷Download the Tydom app.
- Log in to either the Google Play or App Store, depending on your
device.
- Search for and download the free Tydom app.
❸Activate the Wi-Fi connecon on your smartphone or tablet,
and connect to the same local network as your Tydom Home.
❹Configure the Tydom app.
- Note the last 6 characters of your Tydom Home's MAC address.
- Log in to the app and follow the instrucons.
Technical specifications
Power supply via AC adapter
Ktec: KSAS0050500100VED or SPC: ZZU1001-10050-2E
AC values: 100-240V~ 50/60 Hz, 0,18A - DC: 5V 1A
Only these adapters should be used with the Tydom Home.
X3D transmission frequency: 868.7 MHz to 879.2 MHz
Maximum wireless power < 10mW - Category 2 receiver
Zigbee transmission frequency: 2.4 GHz to 2.4835 GHz
Maximum consump on (without USB connec on): 0.9 W
-20°C / +70°C
-10°C / +40°C
IP IP 30
100 x 100 x 26 mm
Help
LED System status
Flashing white System accessible locally and
remotely, user connected
Steady white System accessible locally and
remotely
Flashing orange System accessible locally, user
connected
Steady Orange System accessible locally
Steady Red No IP address allocated
Advanced functions
Below are the funcons accessible depending on
how long the buon on the back of your Tydom
Home is pressed.
A Secure connection and viewing
connection status
Briefly press the buon. LED displays for 10 seconds.
Flashing yellow Stac IP mode
Flashing blue DHCP mode
Flashing blue (3x)
DHCP in progress Check the DHCP
acvaon on the router
Flashing red No network connecon Check
the Ethernet link
BChange from static IP to DHCP
Press the buon for 3 seconds unl the pink LED flashes
slowly. Release.
CReset to factory settings
Press the buon for 30 seconds unl the LED stops
flashing. Release.
System status - DHCP mode
- Clear product associaons
3’’ >15’’ >30’’
>
BA C
Static IP -> DHCP
Advanced functions
RESET
www.deltadore.com
Tydom Home
05/22
A B C D
F
E
G H
B
C
30 cm
min.
Router
MAC : 001A25xxxxxx
MAC : 001A25FFFF123456
MAC : 001A25 xxxxxx
The connecon quality of the product may be
affected by different modificaons of the IP
architecture on which it operates.
These modificaons can be, but are not limited
to, a change of hardware, a soware update or
configuraon, work conducted on your operator’s
equipment or any other mulmedia equipment
such as tablets, smartphones, etc.
IOS is a Cisco trademark or registered trademark in the
United States and in other countries, and is used under
licence. AndroidTM and Google Play are Google LLC
registered trademarks.
Wi-FiTM is a trademark registered by Wi-Fi Alliance.
Because of changes in standards and equipment,
the characteriscs given in the text and the
illustraons in this document are not binding
unless confirmed.
Description
E. System status display LED
F. Ethernet port
G. Mains power socket
H: Configuration/Information button
Box contents
A. Tydom Home
B. Ethernet cable
C. Mains supply
D. Important Product Information
EN Smart Home hub
FR Box maison connectée