Delta Electronics Network Adapter AR User manual

D
VE
C2:0.1uF C3:0.1uF
SW1
F
LCy
C1 R C2 C3 L
G
E
N
N
I
FIG. A
L1
Cy
G'
L2 A
N' D
O
L
AR3/4 ONLY
AR1/4 WITHOUT POWER SW
L'
FIG. B
AR3D ONLY
R
FSW1
LCy
C1 L C3C2
G
E
N
N
I
Cy
L1
G'
D
A
O
N'
L2
L
L'
DELTA PART NO. AR1 AR2 AR2D AR3 AR3D AR4
RATED CURRENT 115VAC 6A 6A 6A 6A 6A 6A
250VAC 6A 6A 4A 5A 4A 6A
IEC CONNECTOR
FUSE HOLDER
1212
POWER SWITCH SP DP SP DP
333
VOLTAGE SELECTOR SW REAR REAR REAR
ELECTRICAL SCHEMATIC FIG. A FIG. A FIG. B FIG. A FIG. B FIG. A
CURRENT FREQUENCY-MHz
RATING .15 .50 1.0 5.0 10 30
03AR 40 60 60 45 40 30
06AR 34 55 56 40 35 25
06AR2D,3D 34 60 60 45 40 30
03AR 6 45 55 50 45 40
06AR 5 25 60 50 45 35
06AR2D,3D 10 10 50 50 45 40
COMMON MODE (L-G) IN 50 OHM SYSTEM
DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM
1. AR series is designed as a high performance, two-stage filter for
low impedance load with better noise attenuation than AK series
in low frequency applications such as switching power supplies.
2. Fuse holder designed for one IEC 5x20mm fuse. Safety interlock
prevents fuse removal with line plug inserted (Use only with 250V
fuse).
3. All part numbers are UL recognized, CSA certified and VDE
approved.
PART NO. C1 (uF) L1 (mH) L2 (mH) Cy (pF) R ( )
03AR1/2/3 0.1 1.5 9 2200 1M
03AR2D/3D 0.033 9 1.5
06AR1/2/3 0.1 0.7 2.5
06AR2D/3D 0.015 2.5 0.7 3300 2.2M
06AR4 0.1 0.7 2.5
1. Single-pole UL, CSA & VDE approved, VDE-6A at 250VAC.
Electrical lifetime: 50,000 cycles.
Maximum inrush current: 50A.
2. Double-pole UL, CSA & VDE approved, VDE-4A at 250VAC.
Electrical lifetime: 10,000 cycles.
Maximum inrush current: 50A.
3. Voltage selector SW -UL, CSA & VDE approved
Current rating: 10A at 125VAC; 5Aat 250VAC.
1. Maximum leakage current each
line-to-ground @ 115VAC 60Hz: 0.25mA
@ 250VAC 50Hz: 0.45mA
2. Hipot rating (one minute)
line-to-ground: 2250VDC
line-to-line: 1450VDC
3. Operating frequency: 50/60Hz
4. Rated voltage: 115/250VAC
4-3
POWER ENTRY MODULE FILTERS
SERIES
SPECIFICATIONS
POWER ENTRY MODULE EMI FILTERS
INTRODUCTIONS
ELECTRICAL SCHEMATIC
COMPONENTS MINIMUM INSERTION LOSS IN dB
TYPE & RATED CURRENT

66.0
1.0
R0.04Max.
27.0
2.6 0.003
1.063 0.003
Suggested thickness of mounting
panel is from 0.04 to 0.07 inch
suggest mounting cutout
INCH
UNIT: mm
AR1
AR3, AR3D
AR4(without power switch)
AR2, AR2D
2.24
56.9
2.57
65.3
1.15 29.2
N
G
L
67.3
2.65
55.1 2.17
1.059
26.9
G
2.60 66.0
115V
1.15
29.2
N L
G
67.3
2.65
I
O
16.5 0.65
G
1.059
26.9
26.9
1.059
L
G
N
G
29.2 1.15
N
O
LI
2.65
67.3
2.38 55.1 60.5 2.17
65.3
2.57
4-4
POWER ENTRY MODULE FILTERS
MECHANICAL CONSTRUCTION