Denon AVR-1802/882 User manual

AV SURROUND RECEIVER
AVR-1802/882
OPERATING INSTRUCTIONS
MODE D’EMPLOI
B
3
0
0
2
67
98
2
3
67
MASTER VOLUME
AVR-1802
PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER
VOLUME LEVEL
B
PHONES CH VOLSURROUND
MODE
SURROUND
PARAMETER
ON / STANDBY
TONE
CONTROL
SELECT
EXT. ININPUT MODE
ABCINEMA EQ TONE DEFEATANALOG
SPEAKER
AUTO
ON / STANDBY DTSPCM
SIGNAL
DIGITAL
INPUT
REMOTE
SENSOR
TUNER
CD
DVD / VDP
VCR-2
PHONO
V. AUX
TV / DBS
VCR-1
INPUT
UP MODEBAND MEMORY
SHIFT
CDR / TAPE DOWN VIDEO SELECT DIMMER STATUS
PRESET
UPDOWN
TUNING
OPTICAL VIDEO
V.AUX INPUT
LAUDIO R
AVR/AVC DVD/VDP
TV VCR
AUDIO
CD MD/CDR
VIDEO
POWER
OFF
ON
DVD/VDP
CDPHONO
TV/DBS
VCR-1 VCR-2
SURROUND
MODE
V.AUX
INPUT MODE
VIDEO SELECT
CDR / TAPE
TUNER SHIFT
CHANNEL
TAPE · VCR
TITLE
DISC SKIP+
CD·MD/CDR·DVD/VDP
STATUS MUTING
T.TONE
MASTER
VOL
CHANNEL TV
SYSTEM
SET UP MENU
SELECT
RETURN DISPLAY
SURROUND
CH SELECT
VOLUME
REMOTE CONTROL UNIT RC-897
2We greatly appreciate your purchase of this unit.
2To be sure you take maximum advantage of all the
features this unit has to offer, read these instructions
carefully and use the set properly. Be sure to keep this
manual for future reference should any questions or
problems arise.
“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO
THE REAR OF THE CABINET FOR FUTURE REFERENCE”
“NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL
INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR
LE CONSULTER EN CAS DE PROBLEME.”
2Nous vous remercions pour l’achat de cet appareil.
2Pour être sûr de profiter au maximum de toutes les
caractéristiques qu’offre cet appareil, lire avec soin ces
instructions et bien utiliser l’appareil. Toujours
conserver ce mode d’emploi pour s’y référer
ultérieurement en cas de question ou de problème.
FOR ENGLISH READERS PAGE 2 ~ PAGE 48, 94, 95 POUR LES LECTEURS FRANCAIS PAGE 2, 49 ~ PAGE 95

2
ENGLISH
2SAFETY PRECAUTIONS
2NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
• Keep the set free from moisture, water, and
dust.
• Protéger l’appareil contre l’humidité, l’eau et la
poussière.
• Unplug the power cord when not using the set
for long periods of time.
• Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
* (For sets with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Do not let foreign objects in the set.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Do not let insecticides, benzene, and thinner
come in contact with the set.
• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
• Never disassemble or modify the set in any
way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
FRANCAIS

3
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions
should be followed.
5. Water and Moisture – The appliance should not be used
near water – for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool, and the like.
6. Carts and Stands – The appliance should be used only with
a cart or stand that is recommended by the manufacturer.
6A. An appliance and cart
combination should be
moved with care.
Quick stops, excessive
force, and uneven
surfaces may cause
the appliance and cart
combination to overturn.
7. Wall or Ceiling Mounting – The appliance should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
8. Ventilation – The appliance should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the appliance should not be
situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or, placed in a built-in
installation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.
9. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
10. Power Sources – The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
11. Grounding or Polarization – Precautions should be taken so
that the grounding or polarization means of an appliance is
not defeated.
12. Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
14. Cleaning – The appliance should be cleaned only as
recommended by the manufacturer.
15. Power Lines – An outdoor antenna should be located away
from power lines.
16. Outdoor Antenna Grounding – If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
See Figure A.
17. Nonuse Periods – The power cord of the appliance should
be unplugged from the outlet when left unused for a long
period of time.
18. Object and Liquid Entry – Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
19. Damage Requiring Service – The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or
exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
20. Servicing – The user should not attempt to service the
appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE

4
ENGLISH
2INTRODUCTION
2ACCESSORIES
Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to provide superb surround sound
listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the
contents of this manual before proceeding.
TABLE OF CONTENTS
Check that the following parts are included in addition to the main unit:
1BEFORE USING
Pay attention to the following before using this unit:
•Moving the set
To prevent short circuits or damaged wires in the connection cords,
always unplug the power cord and disconnect the connection
cords between all other audio components when moving the set.
•Before turning the power operation switch on
Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
operation switch to the standby position before connecting and
disconnecting connection cords.
•Store this instructions in a safe place.
After reading, store this instructions along with the warranty in a
safe place.
•Note that the illustrations in this instructions may differ from
the actual set for explanation purposes.
•V. AUX terminal
The AVR-1802’s front panel is
equipped with a V. AUX terminal.
Remove the cap covering the
terminal when you want to use
it.
zBefore Using ..............................................................................................4
xCautions on Installation ..............................................................................5
cCautions on Handling .................................................................................5
vFeatures......................................................................................................5
bPart Names and Functions.....................................................................6, 7
nRead this first .............................................................................................8
mSetting up the Speaker Systems................................................................8
,Connections .........................................................................................9~15
.Using the Remote Control Unit................................................................16
⁄0 Setting up the system .......................................................................17~21
⁄1 Remote Control Unit..........................................................................22~24
⁄2 Operation ...................……………………………………………………25~29
⁄3 Surround.............................................................................................30~34
⁄4 DSP Surround Simulation .........…………………………………………35~39
⁄5 Listening to the Radio........................................................................40~42
⁄6 Last Function Memory .............................................................................43
⁄7 Initialization of the Microprocessor ......................…………………………43
⁄8 Additional Information........................................................................44~46
⁄9 Troubleshooting ........................................................................................47
¤0 Specifications ...........................................................................................48
List of Preset Codes..................................................................................94, 95
qOperating instructions ............................................................................1
wWarranty ( for North America model only ) ............................................1
eService station list...................................................................................1
rRemote control unit (RC-897) .................................................................1
rt y ui
B
tR6P/AA batteries ....................................................................................2
yAM loop antenna ....................................................................................1
uFM indoor antenna..................................................................................1
iFM antenna adaptor................................................................................1
CH VOLSURROUND
MODE
SURROUND
PARAMETER TONE
CONTROL
SELECT
E
AT
OPTICAL VIDEO
V.AUX INPUT
LAUDIO R

5
ENGLISH
3CAUTIONS ON HANDLING
4FEATURES
•Switching the input function when input jacks are not
connected
A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens,
either turn down the MASTER VOLUME control or connect
components to the input jacks.
•Muting of PRE OUT jack, HEADPHONE jack and SPEAKER
terminals
The PRE OUT jack, HEADPHONE jack and SPEAKER terminals
include a muting circuit. Because of this, the output signals are
greatly reduced for several seconds after the power operation
switch is turned on or input function, surround mode or any other
set-up is changed.
If the volume is turned up during this time, the output will be very
high after the muting circuit stops functioning. Always wait until
the muting circuit turns off before adjusting the volume.
•Whenever the power operation switch is in the STANDBY
state, the apparatus is still connected on some AC line
voltages.
Please be sure to unplug the cord when you leave home for,
say, a vacation.
1. Dolby Pro Logic II decoder
Dolby Pro Logic II is a new format for playing multichannel audio
signals that offers improvements over conventional Dolby Pro
Logic. It can be used to decode not only sources recorded in
Dolby Surround but also regular stereo sources into five channels
(front left/right, center and surround left/right). In addition, various
parameters can be set according to the type of source and the
contents, so you can adjust the sound field with greater precision.
2. Dolby Digital decoder
Dolby Digital, a digital discrete system in which the different
channels are completely independent, recreates “three-
dimensional” sound fields (sounds with a sense of distance,
movement and position) with no crosstalk between channels for
greater reality. In addition, the 5 channels (excluding the 0.1
channel for low frequency effects) have a playback range
extending to 20 kHz, the same as the range of CDs, thus resulting
in clearer, more richly expressive sound.
3. DTS (Digital Theater Systems) decoder
DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.
4. High performance DSP simulates 7 sound fields
Playback is possible in 7 surround modes: 5-channel Stereo, Mono
Movie, Rock Arena, Jazz Club, Video Game, Matrix and Virtual.
You can enjoy a variety of sound effects for different movie
scenes and program sources even with stereo sources not in
Dolby Surround.
5. Personal Memory Plus function
Personal Memory Plus is an advanced version of Personal
Memory. With Personal Memory Plus, the set automatically
memorizes the surround mode, channel volume, surround
parameters, etc., for each of the separate input sources.
6. Remote control unit with pre-memory function
This unit comes with a remote control unit equipped with a pre-
memory function. The remote control command codes for
DENON remote controllable AV components as well as for DVD
players, LD players, video decks, TVs, etc., of other major
manufacturers are prestored in the memory.
7. 6CH EXT. IN jack
This unit is equipped with 6CH EXT. IN jacks for use with audio
formats of the future.
2CAUTIONS ON INSTALLATION
Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or TV.
• Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.
• Noise or disturbance tends to occur particularly when using indoor
antennas or 300 Ω/ohms feeder wires. We recommend using
outdoor antennas and 75 Ω/ohms coaxial cables.
For heat dispersal, leave at least 0.3 ft (10 cm) of space between
the top, back and sides of this unit and the wall or other
components.
B
0.3 ft (10 cm) or more
wall
0.3 ft (10 cm) or more

6
ENGLISH
5PART NAMES AND FUNCTIONS
Front Panel
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
VOLUME LEVEL
PHONES CH VOLSURROUND
MODE
SURROUND
PARAMETER
ON / STANDBY
TONE
CONTROL
SELECT
EXT. ININPUT MODE
ABCINEMA EQ TONE DEFEATANALOG
SPEAKER
AUTO
ON / STANDBY DTSPCM
SIGNAL
DIGITAL
INPUT
REMOTE
SENSOR
TUNER
CD
DVD / VDP
VCR-2
PHONO
V. AUX
TV / DBS
VCR-1
INPUT
UP MODEBAND MEMORY
SHIFT
CDR / TAPE DOWN VIDEO SELECT DIMMER STATUS
PRESET
UPDOWN
TUNING
BAVR-1802
PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER MASTER VOLUME
OPTICAL VIDEO
V.AUX INPUT
LAUDIO R
#0 @7
@8@9 @6 @5 @4 @3 @2 @1 !6!7!9 !8@0
r y i !0 !1 !3 !4 !5q w e
t u o !2
qPower operation switch ..............................................(18, 25, 40)
wHeadphones jack (PHONES)....................................................(28)
ePreset stations selector buttons..............................................(42)
rSPEAKER A/B buttons.................................................(25, 28, 43)
tINPUT MODE button...................................................(26, 29, 33)
yANALOG button ................................................................(26, 29)
uEXT. IN button ...................................................................(26, 29)
iCINEMA EQ button .................................................................(33)
oTONE DEFEAT button .............................................................(27)
!0 VIDEO SELECT button ............................................................(28)
!1 V. AUX INPUT jacks.............................................................(4, 10)
!2 SURROUND MODE button...................................(27, 31, 33, 38)
!3 SURROUND PARAMETER button.....................................(31, 38)
!4 SELECT knob ..................................................(27, 30, 31, 33, 38)
!5 TONE CONTROL button..........................................................(27)
!6 CH VOL button ........................................................................(30)
!7 MASTER VOLUME control......................................................(27)
!8 STATUS button ........................................................................(28)
!9 DIMMER button ......................................................................(28)
@0 Master volume indicator (VOLUME LEVEL)............................(27)
@1 Display
@2 TUNING UP/DOWN button .....................................................(41)
@3 MEMORY button...............................................................(40, 42)
@4 MODE button ..........................................................................(41)
@5 BAND button ...........................................................................(41)
@6 SIGNAL indicators....................................................................(27)
@7 INPUT mode indicators............................................................(27)
@8 Remote control sensor (REMOTE SENSOR) ..........................(19)
@9 Power operation indicator
#0 Input source selector buttons .....................................(26, 31, 33)

7
ENGLISH
Remote control unit
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
B
DVD/VDP
CDPHONO
TV/DBS
VCR-1 VCR-2
SURROUND
MODE
TUNER SHIFT
REMOTE CONTROL UNIT RC-897
STATUS MUTING
T.TONE
MASTER
VOL
TITLE
DISC SKIP+
V. AUX
INPUT MODE CDR / TAPE
CHANNEL TV
CD·MD/CDR·DVD/VDP VIDEO SELECT
SYSTEM
SET UP MENU
SELECT
RETURN DISPLAY
SURROUND
CH SELECT
VOLUME
CHANNEL
AVR/AVC DVD/VDP
TV VCR
AUDIO
CD MD/CDR
VIDEO
POWER
TAPE·VCR
OFF
8
4
9
5
1
0
6
2
7
3
ON
3
0
0
2
67
98
2
3
67
INPUT MODE button ...................(26, 29)
Cursor buttons.......................(17, 32, 36)
System buttons (TV) ..........................(24)
Test tone button.................................(30)
Remote control signal
transmitter .........................................(16)
Master volume control
buttons...............................................(27)
POWER buttons ....................(23, 24, 25)
MUTING button .................................(28)
Mode selector switch............(17, 22, 23)
Input source selector
buttons...................................(26, 31, 33)
Preset stations select
buttons.........................................(22, 42)
System buttons
(CD, MD/CDR, DVD/VDP) ............(22, 24)
SYSTEM (SYSTEM SET UP)
buttons...............................................(18)
System buttons (TAPE, VCR)
buttons.........................................(22, 24)
VIDEO SELECT button.......................(28)
SURROUND MODE
button ........................(27, 30, 31, 33, 36)
SURROUND (SURROUND PARAMETER)
button ..............................(31, 33, 34, 36)
STATUS button...................................(28)

8
ENGLISH
6READ THIS FIRST
This AV Surround Receiver must be setup before use. Following these steps.
2Speaker system layout
Basic system layout
• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:
Subwoofer Center speaker system
Surround speaker systems
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.
7SETTING UP THE SPEAKER SYSTEMS
Step 3 (page 17 to 21)
Finally, setting up the system.
Step 2 (page 16)
Next, insert the batteries into the remote control unit.
Step 1 (page 8 to 15)
Choose the best location to setup the Speakers and connecting the components.

9
ENGLISH
8CONNECTIONS
• Do not plug in the power cord until all connections have been
completed.
• Be sure to connect the left and right channels properly (left with
left, right with right).
• Insert the plugs securely. Incomplete connections will result in
the generation of noise.
•Use the AC OUTLETS for audio equipment only. Do not
use them for hair driers, etc.
• Note that binding pin plug cords together with power cords or
placing them near a power transformer will result in generating
hum or other noise.
• Noise or humming may be generated if a connected audio
equipment is used independently without turning the power
of this unit on. If this happens, turn on the power of this unit.
Connecting the audio components
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1 FRONT
FRONT
PREOUT
CENTER
CENTER
DVD/
VDP
TV/
DBS
VCR-1 VCR-2
S-VIDEO
VCR-1 VCR-2
MONITOR
SUB
WOOFER
SPEAKER SYSTEMS AC OUTLETS
SURROUND AC 120V 60Hz
SWITCHED
TOTAL 120W(1A.)MAX.
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2OPT-2
OPT-2
OPT-1FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
A + B / 12 16
CENTER / 6 16
SURROUND / 6 16
ROUTPUTINPUT LRL
RL
RL RL
RL
RL
L
R
L
R
SUBWOOFER
FRONT
LINE OUT LINE IN
CENTER SURROUND
LINE OUT
Decoders with 6-channel
analog outputs, etc.
Connecting the AC OUTLETS
AC OUTLETS
•SWITCHED
(total capacity –120 W (1 A.))
The power to these outlets is turned on and off in conjunction with the POWER switch on the main
unit, and when the power is switched between on and standby from the remote control unit.
No power is supplied from these outlets when this unit’s power is at standby. Never connect
equipment whose total capacity is above 120 W (1 A.)
NOTE:
Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or other
electrical appliances.
AC CORD
AC 120V, 60Hz
Connecting a tape deck
Connections for recording:
Connect the tape deck’s recording input jacks (LINE IN or REC) to this
unit’s tape recording (OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to
this unit’s tape playback (IN) jacks using pin plug cords.
Tape deck or CD recorder
Connecting a turntable
Connect the turntable’s output cord to this
unit’s PHONO jacks, the L (left) plug to the L
jack, the R (right) plug to the right jack.
NOTE:
This unit cannot be used with MC
cartridges directly. Use a separate head
amplifier or step-up transformer.
If humming or other noise is generated when
the ground wire is connected, disconnect the
ground wire.
Turntable
(MM cartridge)
Ground wire
Use these jacks if you wish to connect external power amplifier(s) to increase the
power of the front and center channels, or for connection to powered loudspeakers.
Connect the internal amplifier’s subwoofer to the subwoofer terminal. (Refer to
page 14.)
Connecting the pre-out jacks
•Analog recording of signals input to the AVR-1802 in digital format is not possible. To record in analog, also connect the analog signals of the
player to the AVR-1802’s analog input terminals.
•The AVR-1802’s OPTICAL OUT terminal is an optical digital output terminal for connection of a CDR recorder, MD recorder or other digital
recording device. Use it for digital recording.

10
ENGLISH
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1 FRONT
FRONT
PREOUT
CENTER
CENTER
DVD/
VDP
TV/
DBS
VCR-1 VCR-2
S-VIDEO
VCR-1 VCR-2
MONITOR
SUB
WOOFER
SPEAKER SYSTEMS AC OUTLETS
SURROUND AC 120V 60Hz
SWITCHED
TOTAL 120W(1A.)MAX.
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2OPT-2
OPT-2
OPT-1FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
A + B / 12 16
CENTER / 6 16
SURROUND / 6 16
OPTICALCOAXIAL
R
L
DIGITAL AUDIODIGITALAUDIO
RL
RL
OUTPUT
OPTICAL
DIGITAL AUDIODIGITALAUDIO
LINE OUT
OUTPUT
DIGITAL OUT DIGITAL OUT
DIGITAL OUT DIGITAL IN
OUTPUT
B
INPUT
Connecting a CD player
Connect the CD player’s analog output
jacks (ANALOG OUTPUT) to this unit’s
CD jacks using pin plug cords.
CD player, etc. equipped
with DIGITAL output
DIGITAL jacks
Use these for connections to audio equipment with digital output.
Refer to page 21 for instructions on setting this terminal.
CD player
•Use 75 Ω/ohms cable pin cords (sold separately) for coaxial
connections.
•Use optical cables (sold separately) for optical connections,
removing the cap before connecting.
CD recorder, MD recorder or other component
equipped with digital output jacks.
Connecting the video equipments
To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.
VOLUME LEVEL
CH VOLSURROUND
MODE
SURROUND
PARAMETER TONE
CONTROL
SELECT
VIDEO SELECT DIMMER STATUS
MASTER VOLUME
OPTICAL VIDEO
V.AUX INPUT
LAUDIO R
R VIDEO OUTOPTICALL
R VIDEO OUTL
OUTPUT
OUTPUT
LINE OUT
DIGITAL OUT
VIDEO OUT
VIDEO OUT
LINE OUT
LR
L
R
L
R
Connecting a TV game equipment
•Connect the TV game equipment’s output jacks to
this unit’s V. AUX INPUT lacks.
TV game
Video camera Connecting a video camera equipment
•Connect the video camera equipment’s output
jacks to this unit’s V. AUX INPUT lacks.
The V. AUX terminal is covered with a cap. Remove this cap in order to use the terminal. (See page 4 for instructions on removing the cap.)

11
ENGLISH
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2OPT-2
OPT-2
OPT-1FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
R OUT
VIDEO
OUT L
AUDIO OUT
COAXIAL
DIGITAL
R OUT
VIDEO
OPTICAL
OUT L
AUDIO OUT
DIGITAL
R OUT IN
AUDIO VIDEO
OUT IN
LRL
RLRL
R OUT IN
AUDIO VIDEO
OUT IN
LRL
RLRL
OPT.-1
R
L
R
L
R
L
R
L
R
L
L
R
L
R
RL
IN
VIDEO
B
TV or DBS tuner
DVD player or video disc player (VDP)
Monitor TV
Connecting a TV/DBS tuner
TV/DBS
•Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT)
to the (yellow) TV/DBS IN jack using a 75 Ω/ohms video
coaxial pin plug cord.
•Connect the TV’s or DBS tuner’s audio output jacks (AUDIO
OUTPUT) to the TV/DBS IN jacks using pin plug cords.
AUDIO
VIDEO
Connecting a DVD player or a video disc player VDP
•Connect the DVD player’s (video disc player’s) video output jack (VIDEO OUTPUT) to the (yellow) DVD/VDP
IN jack using a 75 Ω/ohms video coaxial pin plug cord.
•Connect the DVD player’s (video disc player’s) analog audio output jacks (ANALOG AUDIO OUTPUT) to the
DVD/VDP IN jacks using pin plug cords.
•For better sound quality, we recommend using the DVD player with digital rather than analog connections.
DVD players and VDP can also be connected to the VCR terminals.
AUDIO
VIDEO
MONITOR OUT
•Connect the TV’s video input jack (VIDEO
INPUT) to the MONITOR OUT
jack using a 75 Ω/ohms video coaxial pin
plug cord.
VIDEO
NOTE:
Connection of the video disc Player Equipped with Dolby Digital RF
(AC-3RF) Output Jack.
•Please use a commercially available adaptor when connecting the
Dolby Digital RF (AC-3RF) output jack of the video disc player to
the digital input jack.
Please refer to the instruction manual of the adapter when making
connections.
Video deck 2
•There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
•Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the
(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.
Connecting the audio output jacks:
•Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR-1
OUT jacks using pin plug cords.
Connect the second video deck to the VCR-2 jacks in the same way.
AUDIOAUDIO
VIDEOVIDEO
Connecting a video decks
VIDEO OUT
VIDEO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO IN
Video deck 1
AUDIO IN
AUDIO OUT
VIDEO OUT
VIDEO IN
DIGITAL OUT
DIGITAL OUT

12
ENGLISH
Connecting a video component equipped with S-video jacks
•When marking connections, also refer to the operating instructions of the other components.
•A note on the S input jacks
The input selectors for the S inputs and pin jack inputs work in conjunction with each other.
•Precaution when using S-jacks
This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input from
the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs.
When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the
equipment’s instruction manuals.
FRONT
FRONT
PREOUT
CENTER
CENTER
DVD/
VDP
TV/
DBS
VCR-1 VCR-2
S-VIDEO
VCR-1 VCR-2
MONITOR
SUB
WOOFER
SPEAKER SYSTEMS AC OUTLETS
SURROUND AC 120V 60Hz
SWITCHED
TOTAL 120W(1A.)MAX.
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
A + B / 12 16
CENTER / 6 16
SURROUND / 6 16
IN
S-VIDEO
OUT
S-VIDEO
OUT
S-VIDEO
OUT IN
OUT IN
S-VIDEO
B
DVD player, VDP, etc. Connecting a DVD player or video disc player (VDP)
DVD/VDP
•Connect the DVD player’s or video disc player’s S-Video output jack
to the S-VIDEO DVD/VDP IN jack using an S-Video connection cord.
Connecting a monitor TV
MONITOR OUT
•Connect the TV’s or DBS tuner’s S video input (S-VIDEO INPUT) to the
MONITOR OUT jack using a S jack connection cord.
S-VIDEO
Monitor TV
Connecting a TV/DBS tuner
•Connect the TV’s or DBS tuner’s S video
output jack (S-VIDEO OUTPUT) to the
TV/DBS IN jack using an S jack
connection cord.
S-VIDEO
TV or satellite broadcast tuner
Video deck 1
Connecting the video decks
•Connect the video deck’s S output jack (S-OUT) to the
VCR-1 IN jack and the video deck’s S input jack (S-IN) to the
VCR-1 OUT jack using S jack connection cords.
•Connect the video deck’s S output jack (S-OUT) to the
VCR-2 IN jack and the video deck’s S input jack (S-IN) to the
VCR-2 OUT jack using S jack connection cords.
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
Connect the components’audio inputs and outputs as described on page 11.
Video deck 2

13
ENGLISH
1
4
23
Connecting the antenna terminals
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2OPT-2
OPT-2
OPT-1FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
DIRECTION OF
BROADCASTING
STATION AM LOOP
ANTENNA
(An Accessory)
FM ANTENNA
GROUND
AM OUTDOOR
ANTENNA
FM INDOOR ANTENNA
(An Accessory)
FEEDER
CABLE
75 Ω/ohms
COAXIAL
CABLE
AM loop antenna assembly
Connect to the AM
antenna terminals.
Bend in the reverse
direction.
Remove the vinyl tie
and take out the
connection line.
a. With the antenna
on top any stable
surface.
b. With the antenna
attached to a
wall.
Mount
Installation hole
Mount on wall, etc.
Connection of AM antennas
1. Push the lever. 2. Insert the
conductor. 3. Return the lever.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Notes:
•Do not connect two FM antennas simultaneously.
•Even if an external AM antenna is used, do not disconnect the
AM loop antenna.
•Make sure AM loop antenna lead terminals do not touch metal
parts of the panel.
14mm
9mm
14mm
19mm
5mm
5mm
5C-2V3C-2V
Open the cover
ANTENNA ADAPTER
REMOVE
CLAMP 75 Ω/ohms COAXIAL CABLE
CLAMP CLAMP
PULL
PULL
SHUT
FM antenna adapter assembly
FM ANTENNA
ADAPTER
(An Accessory)

14
ENGLISH
Speaker system connections
•Connect the speaker terminals with the speakers making sure that like
polarities are matched (<with <, >with >). Mismatching of polarities will
result in weak central sound, unclear orientation of the various instruments,
and the sense of direction of the stereo being impaired.
•When making connections, take care that none of the individual conductors
of the speaker cord come in contact with adjacent terminals, with other
speaker cord conductors, or with the rear panel.
Speaker Impedance
•When speaker systems A and B are use separately, speakers with an
impedance of 6 to 16 Ω/ohms can be connected for use as front speakers.
•Be careful when using two pairs of front speakers (A + B) at the same time,
since use of speakers with an impedance of 12 to 16 Ω/ohms.
•Speakers with an impedance of 6 to 16 Ω/ohms can be connected for use
as center and surround speakers.
•The protector circuit may be activated if the set is played for long periods of
time at high volumes when speakers with an impedance lower than the
specified impedance are connected.
NOTE:
NEVER touch the speaker terminals when the power is on.
Doing so could result in electric shocks.
Connecting the speaker cords
1. Loosen by turning
counterclockwise.
2. Insert the cord. 3. Tighten by turning
clockwise.
Connecting banana plugs
Turn clockwise to tighten, then insert the
banana plug.
CDR /
TAPE
CDR /
TAPE
DVD /
VDP
TV /
DBS
DVD /
VDP
TV /
DBS
VCR
-1
VCR
-2
VCR
-1
VCR
-2
VCR-1 FRONT
FRONT
PREOUT
CENTER
CENTER
DVD/
VDP
TV/
DBS
VCR-1 VCR-2
S-VIDEO
VCR-1 VCR-2
MONITOR
SUB
WOOFER
SPEAKER SYSTEMS AC OUTLETS
SURROUND AC 120V 60Hz
SWITCHED
TOTAL 120W(1A.)MAX.
PHONO
CD
SIGNAL
GND
MONITOR
VCR-2
VCR-1
VCR-2OPT-2
OPT-2
OPT-1FL
AM
ANTENNA TERMINALS
LOOP
ANT.
FM
COAX.
75
SL
EXT. IN AUDIO DIGITAL VIDEO
C
FR
SR
SW
COAX.
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
A + B / 12 16
CENTER / 6 16
SURROUND / 6 16
(L)(
R)
(L) (R) (L) (R)
Connection jack for subwoofer with built-in
amplifier (super woofer), etc.
To achieve Dolby Digital (AC-3) playback
effect, use a unit that can sufficiently
reproduce frequencies of under 80 Hz.
SURROUND SPEAKER SYSTEMS
CENTER SPEAKER SYSTEM
FRONT SPEAKER SYSTEMS
•Precautions when connecting speakers
If a speaker is placed near a TV or video monitor, the
colors on the screen may be disturbed by the
speaker’s magnetism. If this should happen, move
the speaker away to a position where it does not
have this effect.
banana plug
System B
FRONT SPEAKER SYSTEMS
System A

15
ENGLISH
Protector circuit
•This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows,
when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long
period which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should
this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with
the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation
condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the
unit, switch off the power and contact a DENON service center.
Note on speaker impedance
•The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with
an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms)
are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set
to cool down, improve the ventilation around the set, then turn the power back on.

16
ENGLISH
9USING THE REMOTE CONTROL UNIT
Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
Inserting the batteries
B
B
Point the remote control unit at the remote control sensor as shown
on the diagram at the left.
NOTES:
•The remote control unit can be used from a straight distance of
approximately 23 feet/7 meters, but this distance will shorten or
operation will become difficult if there are obstacles between the
remote control unit and the remote control sensor, if the remote
control sensor is exposed to direct sunlight or other strong light, or
if operated from an angle.
•Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.
Approx. 23 feet/7 m
30°
30°
wInsert the R6P/AA batteries properly, as
shown on the diagram.
qPress as shown by the arrow and slide
off.
eClose the lid.
NOTES:
•Use only R6P/AA batteries for replacement.
•Be sure the polarities are correct. (See the illustration inside the battery compartment.)
•Remove the batteries if the remote control transmitter will not be used for an extended period of time.
•If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the
battery compartment thoroughly before installing new batteries.
•Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.
•Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is
operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

17
ENGLISH
10 SETTING UP THE SYSTEM
•Once all connections with other AV components have been completed as described in “CONNECTIONS”(see pages 9 to 15), make the
various settings described below on the display.
These settings are required to set up the listening room’s AV system centered around the this unit.
STATUS MUTING
T.TONE
MASTER
VOL
TITLE
DISC SKIP+
CD·MD/CDR·DVD/VDP VIDEO SELECT
SYSTEM
SET UP MENU
RETURN DISPLAY
SURROUND
98
2
3
67
SELECT
CH SELECT
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (•, ª, 0, 1)
Press this change what appears on the display.
SELECT button
Press this to switch the display.
Also use this button to complete the setting.
•System setup items and default values (set upon shipment from the factory)
System setup Default settings
Speaker
Configuration
Subwoofer Mode
Channel Level
Digital Input
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for full-size,
full-range) to automatically set the composition of the signals output
from the speakers and the frequency response.
This adjusts the volume of the signals output from the speakers and
subwoofer for the different channels in order to obtain optimum
effects.
This assigns the digital input jacks for the different input
sources. Input
source
Digital
Inputs
Front Sp.
Large
Center Sp. Surround Sp. Sub Woofer
Small Small Yes
Front & Subwoofer Center Surround L & R —
12 ft (3.6 m) 12 ft (3.6 m) 10 ft (3.0 m) —
Front L Front R Center Surround R
Subwoofer
0 dB 0 dB 0 dB 0 dB0 dB
DVD/VDP TV/DBS
COAXIAL OPTICAL-1
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according to
the listening position.
Surround L
0 dB
1Set the slide switch to “AUDIO”.
2Use the following buttons to set up the system:
AUDIO
CD MD/CDR
VIDEO
This selects the subwoofer speaker for playing deep bass
signals. Subwoofer mode = Normal
—
—
NOTE:
•The system setup is not displayed when “HEADPHONE ONLY”is selected.
CDR/TAPE
OPTICAL-2

18
ENGLISH
Before setting up the system
1
2Press the SYSTEM button to enter the setting.
Check that all the components are correct, then press the POWER operation switch on the main unit or
the POWER button on the remote control unit to turn on the power.
3Press the SELECT or (down) button to switch to the speaker configuration set up.
*SYSTEM SET UP
NOTE:
Press the SYSTEM button again to finish system set up. System set up can be finished at any time. The changes to the settings made up to
that point are entered.
NOTE: Please make sure the “AUDIO”position of the slide switch on the remote control unit.
(Main unit) (Remote control unit)
Setting the speaker configuration
1Use the (left) and (right) buttons to select your front speaker type.
1 FRONT LARGE LARGE SMALL
(left) button (right) button
Press the SELECT or (down) button to switch to the center speaker setting.
2Use the (left) and (right) buttons to select your center speaker type.
2 CENTER SMALL
LARGE SMALL NONE
(left) button (right) button
Press the SELECT or (down) button to switch to the surround speaker setting.
3Use the (left) and (right) buttons to select your surround speaker type.
3 SURR. SMALL
LARGE SMALL NONE
(left) button (right) button
Press the SELECT or (down) button to switch to the subwoofer setting.
NOTE:
•When “Small”has been selected for the front speakers, “Large”cannot be selected for the center speaker.
(Initial)
(Initial)
(Initial)

19
ENGLISH
NOTE:
•When “Small”has been selected for the front speakers, “Large”cannot be selected for the surround speakers.
4Use the (left) and (right) buttons to select your subwoofer setting.
4 S.WOOFER YES
YES NO
(left) button (right) button
Press the SELECT or (down) button to enter the settings and switch to the SUBWOOFER MODE
setting.
•Parameters
Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient volume. When this setting is
selected, low frequencies of below 80 Hz are assigned to the subwoofer.
None…… Select this when no speakers are installed.
Yes/No…. Select “Yes”when a subwoofer is installed, “No”when it’s not installed.
NOTE:
Select “Large”or “Small”not according to the physical size of the speaker, but according to the bass reproduction capacity at 80 Hz. If you cannot
determine the best setting, try comparing the sound when set to “Small”and when set to “Large”, at a level that will not damage the speakers.
Caution:
In case the subwoofer is not used, be sure to set “Subwoofer = No”, or the bass sound of front channel is divided to subwoofer channel and
not reproduced in some mode.
Setting the SUBWOOFER MODE
1Use the (left) and (right) buttons to select the Subwoofer mode.
5 SW MODE NORM
NORM +MAIN
(left) button (right) button
Press the SELECT or (down) button to enter the setting and switch to the SPEAKER DISTANCE
setting.
NOTES:
—Assignment of low frequency signal range —
•The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency
signal range of channels set to “SMALL”in the setup. The low frequency signal range of channels set to “LARGE”are produced from those
channels.
—Subwoofer mode —
•The subwoofer mode setting is only valid when “LARGE”is set for the front speakers and “YES”is set for the subwoofer in the “Speaker
Configuration”settings (see pages 18, 19).
If “SMALL”is set for the front speakers or “NO”is set for the subwoofer, the subwoofer mode setting does not affect playback of low
frequency signal range.
•When the “+MAIN”playback mode is selected, the low frequency signal range of channels set to “LARGE”are produced simultaneously
from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the room,
interference may result in a decrease of the actual volume of the low frequency range.
•When the “NORM”playback mode is selected, the low frequency signal range of channels set to “LARGE”are only produced from those
channels. In this playback mode there tends to be little interference of the low frequency range in the room.
•Try playing the music or movie source and select the playback mode providing the stronger low frequency range sound.
(Initial)
(Initial)

20
ENGLISH
Setting the delay time
Input the distances from the listening position to the speakers and set the surround delay time.
Preparations:
Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right).
L1: Distance from center speaker to listening position
L2: Distance from front speakers to listening position
L3: Distance from surround speaker to listening position
CAUTION:
Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer,
or so that the difference in distance (L2 –L1) is 5 feet or less.
Set the surround speakers (left and right) at the same distance from the front speakers (left and right)
or the subwoofer, or so that the difference in distance (L2 –L3) is 15 feet or less.
L1
L2
L3
FL Center FR
Listening
position
SL SR
1Use the (left) and (right) buttons to set the distance from the front speakers and subwoofer to the
listening position.
6 FRNT/SW 12ft
•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
(“/SW”appears only when subwoofer = yes.)
Press the SELECT or (down) button to switch to the center speaker setting.
NOTE:
•The speaker distance can be adjusted between 0 and 60 feet in steps of 1 foot.
2Use the (left) and (right) buttons to set the distance from the center speakers to the listening
position.
CENTER 12ft
•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
Press the SELECT or (down) button to switch to the surround speaker setting.
NOTE:
•No setting when “None”has been selected for the center speaker.
3Use the (left) and (right) buttons to set the distance from the surround speakers to the listening
position.
8 SURR. 10ft
•The number changes in units of 1 foot each time one of the buttons is pressed. Select the value closest
to the measured distance.
Press the SELECT or (down) button to enter the setting and switch the DIGITAL input (COAX) setting.
NOTE:
•No setting when “None”has been selected for the surround speakers.