Denon In-Command AVR-2313CI User manual

D&M Holdings Inc.
SERVICE MANUAL
e
e
Copyright 2014 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
MODEL JP E3 E2 EK EA E1 E1K E1C
AVR-2313CI
P
AVR-2313
P P
INTEGRATED NETWORK AV RECEIVER
Ver. 3
S0782-0V03DM/DG1401
• Some illustrations using in this service manual are slightly different from the actual set.
• Please use this service manual with referring to the operating instructions without fail.
• For purposes of improvement, specications and design are subject to change without notice.
Please refer to the
MODIFICATION NOTICE.

2
CONTENTS
ABOUT THIS MANUAL.............................................................3
What you can do with this manual ............................................3
Using Adobe Reader (Windows version) ..................................4
SAFETY PRECAUTIONS ..........................................................6
NOTE FOR SCHEMATIC DIAGRAM.........................................7
TECHNICAL SPECIFICATIONS................................................8
DIMENSION ...............................................................................8
CAUTIONS IN SERVICING .......................................................9
Initializing INTEGRATED NETWORK AV RECEIVER ..............9
Service Jig ................................................................................9
DISASSEMBLY ........................................................................10
1. FRONT PANEL ASSY .........................................................12
2. PCB MX PORT/PCB RS232C ............................................13
3. PCB HDMI...........................................................................14
4. POWER TRANS MAIN........................................................15
5. PCB SMPS ASSY................................................................15
6. PCB VIDEO.........................................................................16
7. PCB AUDIO.........................................................................17
8. PCB PREOUT .....................................................................18
9. PCB SPK.............................................................................19
10. RADIATOR ASSY...............................................................20
11. PCB REG/REG_CNT ASSY ..............................................22
SPECIAL MODE ......................................................................23
Special mode setting button....................................................23
1. µcom/DSP Version display mode ........................................24
2. PANEL/REMOTE LOCK Selection mode............................28
3. Service Related Selection mode .........................................29
4. Remote ID Setup mode.......................................................37
BLOCK DIAGRAM...................................................................39
JIG FOR SERVICING ..............................................................55
WHEN THE MICROPROCESSOR IS
REPLACED WITH A NEW ONE ............................................58
PROCEDURE FOR UPGRADING
THE VERSION OF THE FIRMWARE .....................................58
1. How to update by DFW .......................................................58
2. How to update by DPMS .....................................................62
3. How to update by USB Memory ..........................................69
ADJUSTMENT.........................................................................76
SURROUND MODES AND PARAMETERS ............................77
TROUBLE SHOOTING............................................................83
1. POWER...............................................................................83
2. Analog video........................................................................84
3. HDMI/DVI ...........................................................................89
4. AUDIO .................................................................................97
5. Network/USB.....................................................................100
6. SMPS ................................................................................104
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK ...........108
LEVEL DIAGRAM..................................................................109
PRINTED WIRING BOARDS.................................................115
HDMI ....................................................................................115
FRONT HDMI .......................................................................117
REG ......................................................................................117
REG CNT ..............................................................................117
SIDE CNT..............................................................................118
RC5_MCPORT......................................................................119
RS232C.................................................................................119
FRONT .................................................................................120
FUNCTION ...........................................................................122
F/H_GUIDE ..........................................................................122
CNT ......................................................................................122
USB ......................................................................................123
GUIDE L ...............................................................................123
TOP_GUIDE .........................................................................123
GUIDE R ..............................................................................123
7CH AMP ..............................................................................124
VIDEO ..................................................................................126
SPK ......................................................................................127
SMPS ...................................................................................129
PREOUT ...............................................................................130
SCHEMATIC DIAGRAMS......................................................131
HDMI SW UNIT.....................................................................131
FRONT HDMI UNIT ..............................................................132
HDMI RX UNIT......................................................................133
HDMI TX UNIT ......................................................................134
HDMI TX DDR UNIT .............................................................135
DSP UNIT..............................................................................136
DIR/PLD DIGITAL_IN UNIT ..................................................137
MAIN DAC UNIT ...................................................................138
DM860A UNIT .......................................................................139
NET PHY UNIT .....................................................................140
CPU UNIT .............................................................................141
CPU LEVEL CHG UNIT ........................................................142
DIGITAL CNT UNIT...............................................................143
D.SUPPLY/RESET UNIT ......................................................144
7CH-AMP UNIT (1/2) ............................................................145
7CH-AMP UNIT (2/2) ............................................................146
SPK_SMPS UNIT (1/2) .........................................................147
SPK_SMPS UNIT (2/2) .........................................................148
REG_CNT_RS232_RC-5 UNIT (1/4)....................................149
REG_CNT_RS232_RC-5 UNIT (2/4)....................................150
REG_CNT_RS232_RC-5 UNIT (3/4)....................................151
REG_CNT_RS232_RC-5 UNIT (4/4)....................................152
AUDIO UNIT..........................................................................153
VIDEO_PREOUT_TU UNIT (1/3)..........................................154
VIDEO_PREOUT_TU UNIT (2/3)..........................................155
VIDEO_PREOUT_TU UNIT (3/3)..........................................156
FRONT UNIT (1/2) ................................................................157
FRONT UNIT (2/2) ................................................................158
WIRING DIAGRAM................................................................159
EXPLODED VIEW..................................................................160
PARTS LIST OF EXPLODED VIEW......................................161
PACKING VIEW .....................................................................164
PARTS LIST OF PACKING & ACCESSORIES.....................165
SEMICONDUCTORS .............................................................166
1. IC's ....................................................................................166
2. FL DISPLAY.......................................................................196
PARTS LIST OF PCB UNIT...................................................199
7CH_AMP PCB UNIT ASS'Y.................................................199
SPK_SMPS PCB UNIT ASS'Y ..............................................206
REG_CNT PCB UNIT ASS'Y ................................................210
FRONT PCB UNIT ASS'Y .....................................................212
AUDIO PCB UNIT ASS'Y ......................................................215
VPT PCB UNIT ASS'Y...........................................................217
HDMI PCB UNIT ASS'Y ........................................................220

3
ABOUT THIS MANUAL
Read the following information before using the service manual.
What you can do with this manual
Jump to the target of a schematic diagram
connector
Click the Ref. No. of the target connector in the red box
around a schematic diagram connector.
• The screen jumps to the target connector.
• Page magnification stays the same as before the
jump.
Search for a Ref. No. (phrase)
(Ctrl+Shift+F)
You can use the search function in Acrobat Reader to
search for a Ref. No. in schematic diagrams, printed
wiring board diagrams, block diagrams, and parts lists.
1.Press Ctrl+Shift+F on the keyboard.
• The Search window appears.
Ctrl
Shift
F
2.Enter the Ref. No. you want to search for in the
Search window, and then click the Search button.
• A list of search results appears.
3.Click an item on the list.
• The screen jumps to the page for that item, and
the search phrase is displayed.

4
Using Adobe Reader (Windows version)
• Properties
Click this button and check that the printer is set to a
suitable paper size.
• Page to print
Select the following checkbox.
"More Options" : "Current View"
• Page Sizing & Handling
Select the following checkbox.
"Size" / "Size Options" : "Fit"
Add notes to this data (Sign)
The Sign function lets you add notes to the data in this
manual.
Save the le once you have nished adding notes.
[Example using Adobe Reader X]
On the "View" menu, click "Sign".
• The Sign pane appears.
[Example using Adobe Reader 9]
On the "Document" menu, click "Sign".
Magnify schematic / printed wiring board
diagrams - 1
(Ctrl+Space, mouse operation)
[Example using Adobe Reader 9,X]
Press Ctrl+Space on the keyboard and drag the
mouse to select the area you want to view.
• The selected area is magnied.
Ctrl Space
0
• When you want to move the area shown, hold down
Space and drag the mouse.
• When you want to show a full page view, press
Ctrl+0 on the keyboard.
Print a magnied part of the manual
The Properties dialog box and functions will vary depending on your printer.
1.Drag the mouse to magnify the part you want to print.
2. On the "File" menu, click "Print".
3. Congure the following settings in the Print dialog box.
4. Click the Print button to start printing.

5
Magnify schematic / printed wiring board
diagrams - 2
(Pan & Zoom function)
The Pan & Zoom function lets you see which part of a
magnied diagram is being shown in a separate window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then click
"Pan & Zoom".
• The Pan & Zoom window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom", and
then click "Pan & Zoom Window".
Magnify schematic / printed wiring board
diagrams - 3
(Loupe Tool function)
The Loupe Tool function lets you magnify a specific
part of a diagram in a separate window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then click
"Loupe Tool".
• The Loupe Tool window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom", and
then click "Loupe Tool Window".

6
SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service technician.
LEAKAGE CURRENT CHECK
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state (on,
off and standby mode), if applicable.
CAUTION Please heed the following cautions and instructions during servicing and
inspection.
◎Heed the cautions!
Cautions which are delicate in particular for servicing
are labeled on the cabinets, the parts and the chassis,
etc. Be sure to heed these cautions and the cautions
described in the handling instructions.
◎Cautions concerning electric shock!
(1) An AC voltage is impressed on this set, so if
you touch internal metal parts when the set is
energized, you may get an electric shock. Avoid
getting an electric shock, by using an isolating
transformer and wearing gloves when servicing
while the set is energized, or by unplugging the
power cord when replacing parts, for example.
(2) There are high voltage parts inside. Handle with
extra care when the set is energized.
◎Caution concerning disassembly and
assembly!
Through great care is taken when parts were
manufactured from sheet metal, there may be burrs
on the edges of parts. The burrs could cause injury if
ngers are moved across them in some rare cases.
Wear gloves to protect your hands.
◎Use only designated parts!
The set's parts have specic safety properties (re
resistance, voltage resistance, etc.). Be sure to use
parts which have the same properties for replacement.
The burrs have the same properties. In particular, for
the important safety parts that are indicated by the z
mark on schematic diagrams and parts lists, be sure to
use the designated parts.
◎Be sure to mount parts and arrange the wires
as they were originally placed!
For safety seasons, some parts use tapes, tubes or
other insulating materials, and some parts are mounted
away from the surface of printed circuit boards.
Care is also taken with the positions of the wires by
arranging them and using clamps to keep them away
from heating and high voltage parts, so be sure to set
everything back as it was originally placed.
◎Make a safety check after servicing!
Check that all screws, parts and wires removed or
disconnected when servicing have been put back in
their original positions, check that no serviced parts
have deteriorate the area around. Then make an
insulation check on the external metal connectors and
between the blades of the power plug, and otherwise
check that safety is ensured.
(Insulation check procedure)
Unplug the power cord from the power outlet,
disconnect the antenna, plugs, etc., and on the power.
Using a 500V insulation resistance tester, check that
the insulation resistance value between the inplug and
the externally exposed metal parts (antenna terminal,
headphones terminal, input terminal, etc.) is 1MΩ or
greater. If it is less, the set must be inspected and
repaired.
Many of the electric and the structural parts used in
the set have special safety properties. In most cases
these properties are difcult to distinguish by sight, and
the use of replacement parts with higher ratings (rated
power and withstand voltage) does not necessarily
guarantee that safety performance will be preserved.
Parts with safety properties are indicated as shown
below on the wiring diagrams and the parts list in this
service manual. Be sure to replace them with the parts
which have the designated part number.
(1) Schematic diagrams.......Indicated by the z mark.
(2) Parts lists.......Indicated by the zmark.
The use of parts other than the
designated parts could cause electric
shocks, res or other dangerous
situations.
CAUTION Concerning important safety
parts

7
NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If
the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set
is defective.
WARNING:
DO NOT return the set to the customer unless the problem is identied and remedied.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO
FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT
TO CHANGE WITHOUT PRIOR NOTICE.
NOTE FOR PARTS LIST
Parts indicated by "nsp" on this table cannot be supplied.
When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.
A part ordered without specifying its part number can not be supplied.
General-purpose Carbon Chip Resistors are not included are not included in the P.W.Board parts list.
(Refer to the Schematic Diagram for those parts.)
Parts indicated by the zmark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
Part indicated by "★" mark is not illustrated in the exploded view.
WARNING:
1.
2.
3.
4.
5.
6.
●Resistors
RD : Carbon
RC : Composition
RS : Metal oxide film
RW: winding
RN : Metal film
RK : Metal mixture
P : Pulse-resistant type
NL : Low noise type
NB : Non-burning type
FR : Fuse-resistor
F : Lead wire forming
2B : 1/8 W
2E : 1/4 W
2H : 1/2 W
3A : 1 W
3D : 2 W
3F : 3 W
3H : 5 W
F : ±1%
G:±2%
J : ±5%
K : ±10%
M : ±20%
Ex.: RN
Type
14K
Shape
and per-
formance
2E
Power
182
Resist-
ance
G
Allowable
error
FR
Others
*Resistance
1800ohm=1.8kohm1 8 2
Indicates number of zeros after effective number.
2-digit effective number.
1.2ohm1 R 2
2-digit effective number, decimal point indicated by R.
1-digit effective number.
: Units: ohm
●Capacitors
CE : Aluminum foil
electrolytic
CA : Aluminium solid
electrolytic
CS : Tantalum electrolytic
CQ : Film
CK : Ceramic
CC : Ceramic
CP : Oil
CM: Mica
CF : Metallized
CH : Metallized
HS : High stability type
BP : Non-polar type
HR : Ripple-resistant type
DL : For change and discharge
HF : For assuring high frequency
U : UL part
C : CSA part
W : UL-CSA part
F : Lead wire forming
0J : 6.3 V
1A : 10 V
1C : 16 V
1E : 25 V
1V : 35 V
1H : 50 V
2A : 100 V
2B : 125 V
2C : 160 V
2D : 200 V
2E : 250 V
2H : 500 V
2J : 630 V
F : ±1%
G:±2%
J : ±5%
K : ±10%
M : ±20%
Z : ±80%
: - 20%
P : +100%
C : ±0.25pF
D : ±0.5pF
= : Others
Ex.: CE
Type
04W
Shape
and per-
formance
1H
Dielectric
strength
3R2
Capacity
M
Allowable
error
BP
Others
･Units:μF.
2200μF2 2 2
Indicates number of zeros after effective number.
2-digit effective number. ･Units:μF.
2.2μF2 R 2
2-digit effective number, decimal point indicated by R
1-digit effective number.
*Capacity (electrolyte only)
･When the dielectric strength is indicated in AC,"AC" is included after the dielectric strength value.
*Capacity (except electrolyte)
･Units:pF
2200pF=0.0022μF2 2 2
Indicates number of zeros after effective number. (More than 2)
2-digit effective number. ･Units:pF
220pF2 2 1
2-digit effective number.
Indicates number of zeros after effective number. (0 or 1)
NOTE FOR PARTS LIST

8
TECHNICAL SPECIFICATIONS
nAudio Section
• Power amplier
Rated output (for 2313CI model) :
Front :
105 W + 105 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
135 W + 135 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Center :
105 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
135 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
105 W + 105 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
135 W + 135 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround back:
105 W + 105 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
135 W + 135 W (6 Ω, 1 kHz with 0.7 % T.H.D.)
Output connectors : 6 – 16 Ω
• Analog
Input sensitivity/Input impedance : 200 mV/47 kΩ
Frequency response: 10 Hz – 100 kHz — +1, –3 dB (DIRECT mode)
S/N : 100 dB (IHF–A weighted, DIRECT mode)
nVideo section
• Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Ω
Frequency response : 5 Hz – 10 MHz — 0, –3 dB
• Color component video connector
Input/output level and impedance : Y (brightness) signal — 1 Vp-p, 75 Ω
PB / CB signal — 0.7 Vp-p, 75 Ω
PR / CR signal — 0.7 Vp-p, 75 Ω
Frequency response : 5 Hz – 60 MHz — 0, –3 dB
nTuner section
(Note: μV at 75 Ω, 0 dBf = 1 x 10–15 W)
Receiving Range (for E3 model) :
87.5 MHz – 107.9 MHz
Usable Sensitivity :
1.2 μV (12.8 dBf)
50 dB Quieting Sensitivity :
MONO 2.8 μV (20.2 dBf)
S/N :
MONO 70 dB (IHF–A weighted, DIRECT mode)
STEREO 67 dB (IHF–A weighted, DIRECT mode)
Total harmonic Distortion :
MONO 0.7 % (1 kHz)
STEREO 1.0 % (1 kHz)
nGeneral
Power supply (for E3 model) : AC 120 V, 60 Hz
Power supply (for E2 model) : AC 230 V, 50/60 Hz
Power supply (for E1C model) : AC 220 V, 50 Hz
Power consumption : 600 W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power comsumption in network standby mode : 2.7 W
Weight : 10.9 kg
434
344
60
86.035.8 30.2
338.518.5
152 167
15
54.0 214.5
22.0
245
DIMENSION
[AVR-2313CIE3 model]

9
CAUTIONS IN SERVICING
Initializing INTEGRATED NETWORK AV RECEIVER
INTEGRATED NETWORK AV RECEIVER initialization should be performed when the μcom, peripheral parts of μcom,
and Digital PCB were replaced.
1. Turn off the power pressing "Power operation (X)" button.
2. Press "Power operation (X)" button while simultaneously while pressing "ZONE2/REC SOURCE" and "DIMMER"
buttons.
3. Check that the entire display is ashing at intervals of about 1 second, and then release the 2 buttons.
The microprocessor will be initialized.
[AVR-2313CIE3 model]
Service Jig
When you repair the printing board, you can use the following JIG (Extension cable kit).
Please order it from Denon Ofcial Service Distributor in your region if necessary.
8U-110084S : EXTENSION UNIT KIT : 1 Set
(Refer to 55 page.)
NOTE:• If step 3 fails, start over from step 1.
• All user settings will be lost and the factory setting will be recovered after the set is initialized.
So make sure to note down your setting beforehand for restoring after the initialization.
(X) ZONE2 / REC SOURCE
DIMMER

10
DISASSEMBLY
• Disassemble in order of the arrow in the following gure.
• In the case of the re-assembling, assemble it in order of the reverse of the following ow.
• In the case of the re-assembling, observe "attention of assembling".
• If wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as
they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.
FRONT PANEL ASSY
Refer to "DISASSEMBLY
1. FRONT PANEL ASSY"
and "EXPLODED VIEW"
PCB FRONT HDMI
(Ref. No. of EXPLODED VIEW : P1)
PCB USB
(Ref. No. of EXPLODED VIEW : P2)
PCB FRONT
(Ref. No. of EXPLODED VIEW : P3)
PCB FUNCTION
(Ref. No. of EXPLODED VIEW : P4)
PCB CNT
(Ref. No. of EXPLODED VIEW : P5)
PCB FRONT HDMI_GUIDE
(Ref. No. of EXPLODED VIEW : P6)
RADIATOR ASSY
Refer to "DISASSEMBLY
10. RADIATOR ASSY"
and "EXPLODED VIEW"
PCB GUIDE R
(Ref. No. of EXPLODED VIEW : P7)
7CH AMP PCB ASSY
(Ref. No. of EXPLODED VIEW : P8)
PCB TOP_GUIDE
(Ref. No. of EXPLODED VIEW : P9)
PCB GUIDE L
(Ref. No. of EXPLODED VIEW : P10)
POWER TRANS MAIN
Refer to "DISASSEMBLY
4. POWER TRANS MAIN"
and "EXPLODED VIEW"
POWER TRANS
(Ref. No. of EXPLODED VIEW : 32)
TOP COVER
PCB HDMI
Refer to "DISASSEMBLY
3. PCB HDMI"
and "EXPLODED VIEW"
PCB HDMI
(Ref. No. of EXPLODED VIEW : P16)
PCB MX PORT/PCB RS232C
Refer to "DISASSEMBLY
2. PCB MX PORT/PCB RS232C"
and "EXPLODED VIEW"
PCB RS232C
(Ref. No. of EXPLODED VIEW : P15)
PCB RC5_MXPORT
(Ref. No. of EXPLODED VIEW : P17)
PCB VIDEO ASSY
Refer to "DISASSEMBLY
6. PCB VIDEO ASSY"
and "EXPLODED VIEW"
PCB VIDEO
(Ref. No. of EXPLODED VIEW : P22)
PCB AUDIO ASSY
Refer to "DISASSEMBLY
7. PCB AUDIO ASSY"
and "EXPLODED VIEW"
PCB AUDIO ASSY
(Ref. No. of EXPLODED VIEW : P13)
BACK CHASSIS
PCB SMPS
Refer to "DISASSEMBLY
5. PCB SMPS"
and "EXPLODED VIEW"
PCB SMPS
(Ref. No. of EXPLODED VIEW : P18)
PCB REG/REG_CNT ASSY
Refer to "DISASSEMBLY
11. PCB VIDEO ASSY"
and "EXPLODED VIEW"
PCB REG
(Ref. No. of EXPLODED VIEW : P11)
PCB REG_CNT
(Ref. No. of EXPLODED VIEW : P12) PCB PREOUT ASSY
Refer to "DISASSEMBLY
8. PCB PREOUT ASSY"
and "EXPLODED VIEW"
PCB SIDE _CNT
(Ref. No. of EXPLODED VIEW : P14)
PCB FRONT CNT
(Ref. No. of EXPLODED VIEW : P20)
PCB PREOUT
(Ref. No. of EXPLODED VIEW : P21)
PCB SPK ASSY
Refer to "DISASSEMBLY
9. PCB SPK ASSY"
and "EXPLODED VIEW"
PCB SPK
(Ref. No. of EXPLODED VIEW : P19)

11
About the photos used for "descriptions of the DISASSEMBLY" section
• The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as
"Shooting direction: ***".
• Refer to the diagram below about the shooting direction of each photograph.
• Photographs with no shooting direction indicated were taken from the top of the set.
• The photograph is AVR-2313CIE3 model.
The viewpoint of each photograph
(Shooting direction)
［View from the top］
Front side
Shooting direction: B
Shooting direction: D
Shooting direction: C
Shooting direction: A

12
1. FRONT PANEL ASSY
(1) Remove the screws.
(2) Cut the wire clamp band, then disconnect the connector wires and FFC. Remove the screws.
TOP COVER FRONT PANEL ASSY
→
Proceeding :
View from the bottom
N2801 FFC
CP4400
FFC
N3405
STYLE PIN : Loosen STYLE PIN : Loosen
cut
Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.

13
2. PCB MX PORT/PCB RS232C
(1) Remove the screws.
(2) Disconnect the connector board.
TOP COVER BACK CHASSIS
→PCB MX PORT/PCB RS232C →
Proceeding :
Shooting of photograph: A
Shooting of photograph: A
Board to board
PCB RC5_MXPORT
PCB RS232C
Please refer to "EXPLODED VIEW" for the disassembly method of PCB MX PORT/PCB RS232C.

14
3. PCB HDMI
(1 ) Cut the wire clamp band, then disconnect the connector wires and FFC. Disconnect the connector board.
PCB HDMI
→
PCB MX PORT/PCB RS232C
→
TOP COVER BACK CHASSIS
→
Proceeding :
N3601
N2801
Board to board
Board to board
N3405
Board to board
FFC FFC
STYLE PIN : Loosen STYLE PIN : Loosen
cut

15
4. POWER TRANS MAIN
(1) Disconnect the connector wires, then remove the screws.
5. PCB SMPS ASSY
(1) Cut the wire clamp band, then disconnect the connector wire. Remove the screw.
PCB MX PORT/PCB RS232C
→
PCB HDMI
→
POWER TRANS MAIN
→
TOP COVER BACK CHASSIS
→
Proceeding :
CP4142
CP4602
CP4001
CP4400
STYLE PIN : Loosen
PCB VIDEO
PCB MX PORT/PCB RS232C
→
PCB HDMI
→→
PCB SMPS ASSY
TOP COVER BACK CHASSIS
→
Proceeding :
CP4142
cut

16
(2) Remove the screws.
6. PCB VIDEO
(1) Disconnect the connector wire and connector board.
Shooting of photograph: D
PCB MX PORT/PCB RS232C
→
PCB HDMI
→→ →
PCB SMPS ASSY PCB VIDEO
TOP COVER BACK CHASSIS
→
Proceeding :
CP4800
Board to Board
PCB SIDE CNT

17
7. PCB AUDIO
(1) Disconnect the connector wire and connector board.
→
PCB SMPS ASSY PCB VIDEO
PCB MX PORT/PCB RS232C
→
PCB HDMI
→→ →
PCB AUDIO
TOP COVER BACK CHASSIS
→
Proceeding :
CP401
PCB SIDE CNT
Board to Board
Board to Board

18
8. PCB PREOUT
(1) Remove the screws, then disconnect the connector wires
→
PCB SMPS ASSY PCB VIDEO →PCB AUDIO
→
PCB MX PORT/PCB RS232C
→
PCB HDMI
→→
PCB PREOUT
TOP COVER BACK CHASSIS
→
Proceeding :
CP4618
PCB SIDE CNT
CP4002

19
9. PCB SPK
(1) Remove the screws and SUPPORT PC.
(2) Remove the screws, then disconnect the connector wires.
→
PCB SMPS ASSY PCB VIDEO →PCB AUDIO
→
PCB MX PORT/PCB RS232C
→
PCB HDMI
→→
PCB SPK
TOP COVER BACK CHASSIS
→
Proceeding :
View from the bottom SUPPORT PC
CP405CP403CP402
CP4602

20
10.RADIATOR ASSY
(1) Cut the wire clamp band. Remove the screws, then disconnect the connector wires.
(2) Remove the screws.
TOP COVER RADIATOR ASSY
→
Proceeding :
N2801 FFC
CP4400CP402CP401
FFC
N3405
CP405
CP403
STYLE PIN : Loosen
STYLE PIN : Loosen
cut
View from the bottom