Denver CR-612 User manual

DENVER CR-612 Instruction Manual
1. ON/OFF/AUTO
2. LCD DI PLAY
3. BATTERY BACK-UP
4. NOOZE/ LEEP OFF
5. ALARM ET/ ALARM OFF
6. TIME ET
7. LEEP ET
8. HOUR ET
9. MINUTE ET
10.VOLUME CONTROL/ BUZZ
11.WAVE BAND
12.TUNING CONTROL
13. EN OR PLUG JACK
14.FM ANTENNA WIRE
15. AC POWER CORD
16.POINTER
17.PROJECTION CLOCK ON/OFF
BUTTON
18.PROJECTION TEMPERATURE
ON/OFF BUTTON
19. ℃/℉ BUTTON
20.IN/OUT DOOR BUTTON
21.FOCU ADJU TMENT
(TEMPERATURE)
22.FOCU ADJU TMENT (TIME)
23.PROJECTOR (TEMPERATURE)
24.PROJECTOR (TIME)
25.RE ET BUTTON
26. EN OR PLUG
27. OUTDOOR EN OR
28. INDOOR EN OR
AC POWER OPERATION
Before connecting to the power supply ensure that the supply corresponds to the
DENVER CR-612 English Instruction Manual
1/6

information on the rating label on the bottom of the apparatus.
WARNING
Disconnect the mains plug from the supply socket when not in use. To avoid the
risk of electric shock, do not remove the cover of the apparatus. There are no
user serviceable parts inside. To prevent fire or shock hazard, do not expose the
apparatus to rain or moisture.
CLOCK
1. et the ON/OFF/AUTO witch (1) to “OFF”. Connect the Mains Cord to the
power supply. The clock display on for 3 second.
2. Press and hold the TIME ET (6) for 2 second to enter set clock mode. All
digits are flashing.
3. Press HOUR ET (8) to increase hour and hold to fast running.
4. Press MIN ET (9) to increase minute and hold to fast running.
5. Press TIME ET (6) to return clock mode.
6. If no key press for 5 second, it will return to clock mode
7. Open the CLOCK BATTERY COMPARTMENT door (3) and fit a 9V battery.
The purpose of this battery is to store the information relating to alarm time.
And to keep the clock functioning in the event of disconnection from the
mains supply or power interruption. hould this occur, the clock will continue
to keep time.
THE LCD DIGITAL CLOCK AND THE PROJECTION CLOCK
MU T BE ET EPARATELY
Focus setting: To adjust the projection clock and projection temperature
brightness by turning the Focus (21,22) until the project’s time and temperature is
clearly shown on the ceiling or wall.
NOTE: PROJECT IMAGE ON THE CEILING OR WALL OF A
DARKENED ROOM.
MAXIMUM PROJECTION DI TANCE I 3-9 FEET
TO SET OR RESET THE ALARM TIME
1. Press and hold the ALARM ET (5) for 2 second to enter set alarm mode. All
digitals are flashing.
2. Press HOUR ET (8) to increase hour and hold to fast running.
3. Press MIN ET (9) to increase minute and hold to fast running.
4. Press ALARM ET (5) to return clock mode.
5. If no key press for 5 second, it will return to clock mode.
DENVER CR-612 English Instruction Manual
2/6

TO SET THE ALARM TO WAKE TO RADIO
1. et the alarm time as previously instructed. elect a radio station and make
sure the VOLUME is set as desired.
2. lide the ON/OFF/AUTO switch (1) to the AUTO position. The symbol
(((‧))) will be displayed. When the actual time matches the selected preset
alarm time, the unit automatically turns on for 1 hour and 59 minutes and then
shuts off.
TO SET THE ALARM TO WAKE TO BUZZER
1. et the alarm time as previously instructed. lide the VOLUME BUZZER
knob (10) to the BUZZER position; a click is heard and the buzzer will now
be activated.
2. lide the ON/OFF/AUTO switch (1) to the AUTO position. When the actual
time matches the selected preset alarm time, the unit automatically turns on
for 1 hour and 59 minutes and then shuts off.
TO SHUT ALARM OFF
1. To shut off the alarm, press the ALARM OFF button (5) once and alarm time
will be reset for the next day. lide the ON/OFF/AUTO switch (1) to the OFF
position to turn off alarm and not set it for the next day.
NOTES: The radio can be temporarily turned off manually by pressing the
NOOZE button (4); the radio will turn back on automatically 9
minutes later.
SNOOZE FUNCTION
1. The alarm can be temporarily turned off manually by pressing the NOOZE
button (4); the buzzer will turn back on automatically 9 minutes later.
SLEEP
1. et the ON/OFF/AUTO witch (1) to “OFF” or “AUTO”.
2. Press and hold the LEEP KEY (7) for 2 second to enter set sleep mode.
3. Press LEEP KEY (7) to decrease time from the below
4. 1 hour 30 min  1 hour 00 min  30 min  off  back to 1 hour 30 min
5. If no key press for 5 second, it will return to clock mode.
6. The radio will now operate until the sleep time has elapsed or may be
switched off by pressing the nooze/ leep off Button (4).
RADIO
1. et the ON/OFF/AUTO/ witch (1) “ON” position.
2. et the Waveband witch (11) to the required waveband.
3. Adjust the Tuning Control (12) to select the desired station.
DENVER CR-612 English Instruction Manual
3/6

4. Adjust the Volume Control (10) is required.
5. To turn off the radio, set the ON/OFF/AUTO witch(1) to ”OFF”. If the radio
does not switch off, it may be caused by the inadvertent operation of leep et
Button (7). To cancel this by pressing the nooze/ leep Off Button (4) once.
NOTES: - The AM bands use an internal directional aerial. Rotate the radio for
best reception.
- For best FM reception ensure that the FM cord antenna is completely
unrolled and extended. Rear side of cabinet.
HOW TO VIEW THE INDOOR OR OUTDOOR TEMPERATURE
READING
1. Your thermometer will either be showing the indoor or outdoor temperature.
2. Press the °C/ °F button (19) to toggle the centigrade (°C) and Fahrenheit (°F)
of the temperature.
3. Press indoor/ outdoor temperature button (20) to toggle the indoor or outdoor
temperature in display.
RESET
hould you receive external interference e.g. static electricity from carpets,
thunderstorms, etc. which affects the display and electronic functions of your set,
RE ET allows you to clear all previous settings and start up again.
Use a ballpoint pen to press the RE ET BUTTON (25).
SPECIFICATIONS
For Unit
Frequency range: AM530 – 1600kHz
FM88 – 108MHz
peaker impedance: 8 ohm
Battery backup: 9V Battery (for clock)
Power source: AC 230V ~ 50Hz, 5 Watt
For Thermometer
Operating temperature: 0°C to 50°C (32°F to 122°F)
Temperature measuring range: Unit - Indoor sensor: 0°C to 50°C/ 32°F to
122°F
Probe - Outdoor sensor: -45°C to 65°C/ -49°F to
149°F
Indoor ensor - 0.5°C per step in temperature measure
Outdoor ensor - 1°C per step in temperature measure
DENVER CR-612 English Instruction Manual
4/6

Dripping Warning: “The product shall not be exposed to dripping or splashing
and that no objects filled with liquids, such as vases, shall be
placed on the products.”
Ventilation Warning: “The normal ventilation of the product shall not be impeded
for intended use.”
CAUTION
- The content of this manual is subjected to change without further notice.
-Due to printing limitation, the displays shown in this manual may differ
from the actual displays.
-The manufacturer and its suppliers held no responsibility to you or any
other person for any damages, expenses, lost profits, or any other
damages arise by using this Weather Thermometer.
-The contents of this manual may not be reproduced without the permit of
the manufacturer.
Fasten the projector joints with screwdriver (not included) if loosen
ALL RIGHT RE ERVED
DENVER CR-612 English Instruction Manual
5/6

COPY RIGHT DENVER ELECTRONIC
www.denver-eletronics.com
DENVER CR-612 English Instruction Manual
6/6