Denver DMB-100HD User manual

DMB-100HD
DVB-T PLAYER
Digital Set Top Box
Operating Manual

Safety Instructions
Disclaimer
Information in this document is subject to change without notice.
The manufacturer does not make any representations or warranties
(implied or otherwise) regarding the accuracy and completeness of this
document and shall in no event be liable for any loss of profit or any
commercial damage, including but not limited to special, incidental,
consequential, or other damage.
Always read the safety instructions carefully
Keep this Instruction Manual for future reference
Keep this device away from humidity
Lay this device on areliable flat surface before setting it up
Do not stand it on soft furnishings
If any of the following situation arises, get the Set Top Box checked by
aservice technician:
It has been exposed to moisture
It has been dropped and damaged
It has obvious sign of breakage
It has not been working well or you cannot get it to work according
to the Instruction Manual
Warning
To prevent the risk of electric shock, do not open the cover or the
back of the receiver.
Do not block the ventilation holes of the device. Leave appropriate
gap above and around it to allow for adequate ventilation.
Do not place the device in an unventilated cabinet or on top of aunit
which emits heat.
Copyright Statement
No part of this publication may be reproduced in any form by any means
without the prior written permission. Other trademarks or brand names
mentioned herein are trademarks or registered trademarks of their
respective companies.
1

- -
+ +
CH VOL
VCR SCART
COAXIAL
HDMI
USB
~ 110-240V 50/60Hz
ANT
IN OUT TV SCART
1. Power switchbutton.
2. PROG+/-¡¢VOL+/-.
3. Remote receivesensor.
4. LED indicatorlamp.
5. LED displaypanel.
23457
21
16
345
Front Panel
Rear Panel
2
1. RF IN/RFLOOP THROUGH
TV RF IN socket connectsto your external aerial.
LOOP THROUGH socket will bypass the input RFsignal to anothertuner.
2. VCR SCART OUTPUT/INPUT
In DVB workmode, this terminal output CVBS signal;
When press TV/VCR button in remote control, TV SCART outputs VCR signal;
3. TV SCART OUTPUT
This terminal outputCVBS or RGB signal, you can switch it in menu, and the
default setting isCVBS output;
4. HDMI OUTPUT
High Definition Multimediaoutput, supprot up to 1080i format output;
5. USB
You can update software from USB terminal.
6. COAXIAL: This socket connects to a coaxial socket on your surround sound
system to outputdigital audio.
7. POWER INPUT
Power cord input,and the power supply AC 110~240V
The unit willautomatic power off at standby mode if no operation is performed
after 3 hours,TV screen will display ¡°power down after 120 seconds¡±before
unit power off, select exitbutton by remote control to cancel standby mode.

MUTE STANDBY
MENU
OK
PROG+
PROG-
VOL+
VOL-
EXIT
TEXT
EPG
FAV TV/VCR
INFO
LIST
TV/RADIO
AUDIO
SUB.T
RECALL
16 16
15
17
18 19
15
13 14
11
12
10
79
8
12
6
5
4
3
Remote Control Unit
1)MUTE: Used toturn the soundon or off.
2)STANDBY: Used to switch the set top
box to onand off.
3)NUMBER KEYS: Used toselect channel
numbers or inputnumbers in menus.
4)TV/RADIO: Used toswitch between TV
channels and Radiostations.
5)AUDIO: Used toset the soundoutput,
the available settingsare STEREO,
LEFT,RIGHT,MONO.
6)SUB.T: Used toswitch between different
subtitles that arebroadcasted.
7)LIST: To display thechannel list.
8)INFO: Used todisplay information about
the channel beingviewed.
9)TEXT: Used toopen teletext OSDdisplay
if teletext availablein the broadcastedstream.
10)COLOUR KEYS(RED/GREEN/YELLOW
/BLUE): Used tooperate different functions
in TEXT screen or other menus.
11) FAV: Used to access your favourite channels.
12)TV/VCR: Used toswitch output between
STB and VCR.
13)MENU: Used toopen the mainmenu window.
14)EXIT: Used toreturn to theprevious screen
or menu.
15)PROG+/PROG-: To select channelsupward
or downward ,or move upwardor downward in
menu operation.
16)VOL+/VOL-: To adjust volumeor selected
menu item inmenu operation; Tomove left or
right in menuoperation.
17)OK: Used toconfirm a selectionwithin a menu.
18)EPG: Used todisplay information about
the program beingviewed and whatis on next.
19)RECALL: Used toswitch between the
last two viewedchannels.
3

Installing the Batteries
Remove the batterycover from theRemote Control andput 2xAAAsize
batteries inside thecompartment.
The diagram insidethe Battery Compartment showsthe correct wayto
install the batteries.
OPEN
CLOSE
1.Open the cover 2.Install batteries 3.Close the cover
4

(1) Select [OSDLanguage] and pressRIGHT/LEFT key to select anlanguage
(2) Select [Country]and press RIGHT/LEFTkey to selectyour country of
residence
(3) Select [Channel Search] and press RIGHT or OK key to begin Automatic
channel search
(4) Once channel tuning is complete, you are now ready to watch TV
First Time Installation
Basic Operation
(1) Program Manage Settings
Toaccess the Menu,press the MENUbutton and select[Program]. The
Menu provides optionsto adjust theProgram Manage Settings. Select an
option and press OK or RIGHT to adjust that setting. Press the EXIT button
to exit the Menu.
Program Edit
EPG
Sort By LCN
LCN On
Program
OSD Language English
Country France
Channel Search
Installation Guide
ConfirmExit
OK
Exit
ConfirmReturn
OK
Exit
5
After all connectionshave been madeproperly, switch on TV and make
sure the receiveris connected tothe Main Power. Press PowerButton to
switch receiver on.If you areusing the receiverFor the first time or
restored to FactoryDefault, the MainMenu will appearon your TV screen.

(2) Program Edit
Toedit your programpreferences (lock, skip,favourite, move ordelete), you
will need toenter the ProgramEdit Menu. This Menu requiresa password to
access. Enter thedefault password '000000'.
6
003 ITV1
004 Channel 4
006 ITV2
010 ITV3
013 More 4
014 E4
030 ITV4
037 Quiz Call
Program Edit
LockMove
ALL TV
21:00-22:30 Secret Smile
22:30-22:50 ITV News
DeleteSkip RenameFAV
GOTO
FAV

Move aTV or Radio Program/s
1. Select thepreferred program thenpress the REDbutton. Amovesymbol
will appear
2. Press UP/DOWNto move theprogram
3. Press OKto confirm
4. Repeat theabove steps tomove more channels
Lock Program/s
You can lock selected programs for restricted view.
Lock a TV or RadioProgram:
1.Select the preferredprogram then pressthe YELLOW button. A lock-shaped
symbol is displayed.The program is now markedas locked
2. Repeat theprevious step toselect more programs
3. To confirm andexit the menu,press the EXITbutton
4. Press theYELLOW button to disable thelocked program
5. To view thelocked program, youwill be requireto enter eitherthe default
password '000000' oryour last setpassword.
(3) EPG (Electronicprogram guide)
The EPG isan on-screen TV guide thatshows scheduled programsseven
days in advancefor every tunedchannel. Press theEPG button onthe Remote
Control to accessguide.
You can use the UP/DOWN key to select the preferred program. If there is
more than onepage of information,use the BLUEbutton for pageup and
the YELLOW button for pagedown.
(4) Sort
Sort your channelsfrom the followingoptions:
[LCN] - Sortthe channels inascending order
[Name] - Sort the channels in alphabetical order
[Service ID] - Sort the channels according to the station
(5) LCN (Logicalchannel number)
Set LCN on or off.
7
Page DownBook
OK
Book LIST
INFO
Page Up
Program Guide
13 Dec 21:00 - 22:30 Secret Smile
13 Dec 22:30 - 22:50 ITV News
13 Dec 22:50 - 22:54 Central News
13 Dec 22:54 - 22:56 Central Weather
13 Dec 22:56 - 23:00 ITV News
13 Dec 23:00 - 00:00 Charlotte Church:..
14 Dec 00:00 - 00:53 Cannonball 8000..
14 Dec 00:53 - 00:55 ITV News Headlines
14 Dec 00:55 - 02:40 Inventing The Ab.
14 Dec 02:40 - 04:13 The Haunted Heart
14 Dec 04:13 - 04:15 Secret Smile
003 ITV1
Amusement
David Tennant, Claire Goose &
Kate Ashfield star in the
conclusion of this 2- part thriller
based on a Nicci French novel.
The police find no evidence
against Brendan and accuse
Miranda of paranoia.
Page:1/1
Secret Smile
Tue. 13 Dec 2005 21:5

(1). Aspect Ratio
(2). Resolution
(3). TV format
You must set the display format to either 4:3 PanScan, 4:3 Letter Box,16:9
Full Screen or Auto to get the maximum display when watching TV.
If the video does not appear correctly, change the setting. This setting is to
match the most common setting for HDMI.
[480i]: for NTSC system TV.
[480P]: for NTSC system TV.
[576i] for PAL system TV.
[576P]: for PAL system TV.
[720P]: for NTSC or PAL system TV.
[1080I]: for NTSC or PAL system TV.
If the video does not appear correctly, you need to change the settings.
This should match the most common setting for TVs in your country.
[NTSC]: for NTSC system TV.
[PAL ]: for PAL system TV.
(6) Video Setting
To access the Menu,press MENU thenselect [Picture]. The Menu
provides options toadjust the videosettings. Press UP/DOWNto select an
option and pressRIGHT/LEFT to adjust that setting.Press EXIT to exit themenu.
8
Aspect Ratio 16:9 Wide Screen
Resolution 1080i
TV Format PAL
Video Output CVBS
Picture
ConfirmReturn
OK
EXIT

1 . Auto Search
Search and install all channels automatically. This option overwrites all
preset channels.
1. Select [Auto Search] and press OK or RIGHT to start channel search.
2. To cancel channel search, press EXIT.
2. Manual Search
Install new channels manually. This option adds new channelswithout
changing the currentchannels list.
1. Select [ManualSearch] then pressOK or RIGHT. The channel search
screen will appear
(7) Channel Search
To access the menu,press MENU and select [Search Channel]. The Menu
provides options toadjust the SearchChannel settings.
Select an optionand press RIGHT/LEFTto adjust thesettings.
Press EXIT to exit theMenu.
001 ITV1
002 ITV2
003 ITV3
004 ITV News
005 Channel 4
006 Quiz Call
007 E4
008 More 4
009 ITV4
Channel Search
Progress
506.0MHz/8MHZ
DTV:009 Radio: 000
Quality
Manual Search
SkipExit
MENU
EXIT
Confirm
EXIT
OK
EXIT
Frequency channel 21
Frequency(MHz) 474.0
Bandwidth: 8M
Auto Search
Manual Search
Country France
Antenna Power Off
Channel Search
ConfirmReturn
OK
EXIT
9

2. Press theRIGHT/LEFT key to select thechannel frequency
3. Press OKto start searchingchannels
If a channelis found, itis saved andadded to the channels list. If channels
cant be found,then exit themenu.
'
Enable Antenna Power if an external active antenna is connected.
(8) Time Setting
Press UP/DOWN to select an option and press RIGHT/LEFT to adjust the
s.
(3) Country
Select your country of residence.
(4) Antenna power
Toaccess the Menu,pressMENU then select[Time]. TheMenu provides
options to adjust the time settings.
setting .Press EXIT to exit the menu
(1) Time offset
(2) Country Region
Select the Country Region when [Time Offset] is set to Auto.
Toaccess the Menu,pressMENU and select[Option]. The menu provides
options to adjustthe OSD Language,Subtitle Language andAudio Language.
Select an optionand press RIGHT/LEFTto adjust thesetting.
Press EXIT to exit The Menu.
Select auto or manual for GMT offset adjustments.
(3) Time Zone
Select the Time Zone Offset when [Time Offset] is set to Manual.
(9) Option
Time Offset Auto
Country Region London
Time Zore GMT +0
Time
ConfirmReturn
OK
EXIT
OSD Language English
Subtitle Language English
Audio Language English
Digital Audio PCM
Option
ConfirmReturn
OK
EXIT
10

(1). OSD Language
(2). Audio Language
(3). Subtitle Language
Toaccess the Menu,pressMENU and select[System].The menu
Provides options toadjust the systemsettings.
Press the UP/DOWNkey to selectan option andpress RIGHT/LEFT to
adjust the setting.
Press EXIT to exit theMenu .
Select an OSD language
Select the preferredaudio language forwatching TV channels.
If the languageis not available,the default programlanguage will beused.
Select the preferred subtitle language.
(10) System Setting
(1) Parental Guidance
You can restrict access to channels that are unsuitable for children.
Torestrict/lock the channelyou will needto enter eitherthe
default password '000000'or your ownpassword.
(2) Set Password
Set or changethe password forLocked programs. Enteryour old
Password or thedefault password '000000'.Youwill then beasked to
enter your newpassword. To confirm re-enteryour new password.Once it
is confirmed, pressEXIT to exit the Menu.
11
Parental Guidance
Set Password
Restore Factory Default
Information
System
ConfirmReturn
OK
EXIT

(3) Restore Factory Default
Reset your SetTop Box tothe Default FactorySettings.
In Main Menuselect [Restore FactoryDefault] and pressOK or RIGHTto
select. Enter yourpassword or thedefault password '000000'and press OK
to confirm. This option willdelete all presetchannels and settings.
(4) Information
View model, hardware and software information.
(5) Software update
If the statusis set ''ON'',it will beginsearching for newsoftware from
broadcast according toyour preferred timein ''Start Time''.
(11)USB
To access the Menu, press the Menu button and select USB.
Multi-Media
Switch to USBmode and plugin USB toview files.
12
Multimedia
Photo Configure
USB
ConfirmReturn
OK
EXIT

The image stopped
suddenly or mosaic
Problem Potential Reasons What to do
No picture Power isn'tconnected Connect the power
The power switch is not on Switch on the power
Screen shows
No Signal
DVB-Tcable not connected
Plug in the DVB-Tcable
Incorrect setting Reset setting
No sound from
speaker
No or incorrect connection
with audio cable
Connect the audio cable
correctly
Sound on mute Turn off mute function
Incorrect sound track Try another sound track
Only sound, no
image on the
screen
No or incorrect connection
with AV cable
Make sure cables are
connected correctly
The program is aradio
program
Press <TV/RADIO> key to
shift into TV mode
Remote Control
is not responding
The battery is exhausted Change battery
Remote Control is not
facing or close enough
to the Set Top Box
Adjust the position of the
Remote Control and move
closer to the unit
The signal is too weak Strengthen the signal
Troubleshooting
13

Video Decoder Format MPEG4 AVC /H.264 HP@L4
MPEG2 [e-mail]
Output Format 576P, 720P, 1080i, 4:3 and 16:9
Output Port HDMI
Audio Decoder Format MPEG-1 (layer1&2)
Audio output Digital audio: S/PDIF
Power Voltage AC 110-240V 50/60Hz
Working Power 8W
Item Sub Item Parameter
Tuner Input Frequency 170~230MHz
470~860MHz
RF Input level -25~-82dBm
IF Bandwidth 7MHz and 8MHz
Modulation QPSK,16QAM,64QAM
Technical Specifications
14
0.5W
Standby power

Electric and electronicequipment and included batteries contains
materials, components andsubstances that can be hazardous to
your health andthe environment, if the waste material(discarded
electric and electronicequipment and batteries) is not handled
correctly.
Electric and electronicequipment and batteries is marked withthe crossed
out trash cansymbol, seen below. This symbol signifies thatelectric and
electronic equipment andbatteries should not be disposed ofwith other
household waste, butshould be disposed of separately.
As the enduser it is important that yousubmit your usedbatteries to the
approriate and designatedfacility. In this manner you make surethat the
batteries are recycledin accordance with legislature and willnot harm the
environment.
All cities haveestablished collection points, where electric andelectronic
equipment and batteriescan either be submitted free ofcharge at recycling
stations and othercollection sites, or be collected fromthe households.
Additional information isavailable at the technical department ofyour city.