Desa THE SAVANNAH V3610ST User manual

SEE-THROUGH WOOD
BURNING FIREPLACE
INSTALLATION AND OPERATING
INSTRUCTIONS
Save this manual for future reference.
Save this manual for future reference.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
THE SAVANNAH
Model V3610ST
WARNING:Thisfireplaceisintendedforuse
withwood,orifadecorativegasapplianceis
installed, burn propane or natural gas only.
WARNING: Always leave glass doors fully
opened or fully closed when operating the
appliance.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WARNING: Improper installation, adjust-
ment, alteration, service, or maintenance
cancauseinjuryorpropertydamage,orloss
oflife.Refertothismanualforcorrectinstal-
lation and operational procedures. For as-
sistance or additional information consult a
qualified installer, service agency, or the
gas supplier.
SAVE THIS BOOK
This book is valuable. In addition to instruct-
ing you on how to install and maintain your
fireplace,italsocontainsinformationthatwill
enable you to obtain replacement parts or
optionalaccessoryitemswhen needed. Keep
it with your other important papers.
Thiswoodburningfireplacecomplies
with UL 127 as a FACTORY BUILT
FIREPLACE and is listed and tested
by Underwriters Laboratories Inc.
Check local codes before installing this
fireplace.

55253C
2
For more information, visit www.desatech.com
For more information, visit www.desatech.com
TABLE OF CONTENTS
PRODUCT DIMENSIONS
Figure 1 - Product Dimensions
PRODUCT DIMENSIONS
24"
(60.9cm)
19"
(48.2cm)
4
1
/ 2 "
(11.4cm)
1
1
/ 2 "
(3.8cm)
37
1
/ 2 "
(95.2cm)
36
1
/ 2 "
(92.7cm)
20
1
/ 2 "
(52cm)
15
1
/ 2 "
(39.3cm)
9
1
/ 2 "
(24.1cm)
2
1
/ 2 "
(6.3cm)
42
5
/ 8 "
(108.2cm)
21
5
/ 16 "
(54.1cm)
15
3
/ 8 " Dia.
(38.7cm)
O.D. 10" Dia. I.D.
(25.4cm)
24"
(60.9cm)
6"
(15.2cm)
52
3
/ 4 "
(134cm)
17"
(40.6cm)
10
1
/ 4 "
(26cm) 11
1
/ 4 "
(28.5cm)
7"
(177mm)
Outside Air
Left Side View Front View
Top View
Gas Line
Conduit
17
3
/ 16 "
(43.6cm) 12"
(30.4cm)
12"
(304mm)
TABLE OF CONTENTS
PRODUCT DIMENSIONS........................................................... 2
INTRODUCTION......................................................................... 3
SAFETY INFORMATION ............................................................ 3
BEFORE YOU BEGIN ................................................................ 3
FIREPLACE INSTALLATION ...................................................... 4
OUTSIDE AIR KIT INSTALLATION............................................. 7
GAS LINE INSTALLATION ......................................................... 7
VENTING INSTALLTION ............................................................ 8
OPERATING GUIDELINESAND MAINTENANCE
INSTRUCTIONS ................................................................. 14
TECHNICAL SERVICE ............................................................. 15
REPLACEMENT AND ACCESSORY PARTS........................... 16
OWNER'S REGISTRATION FORM .......................................... 17

55253C
3
3
For more information, visit www.desatech.com
For more information, visit www.desatech.com
INTRODUCTION
SAFETY INFORMATION
BEFORE YOU BEGIN
INTRODUCTION
Model V3610ST series is a wood-burning fireplace intended and
approved for installation in either residential homes or buildings of
standardconstruction.Thisfireplacesystemrequirestheutilization
of a DESA 10" double wall, snap-lock flue pipe system.
GLASS DOORS are optional with this fireplace and come in
different styles. For further details (see page 14).
BE SURE TO CHECK WITH YOUR LOCAL BUILDING
CODES FOR AREA REQUIREMENTS BEFORE IN-
STALLING THIS FIREPLACE.
SAFETY INFORMATION
1. This fireplace reaches high temperatures. Keep children and
adults away from hot surfaces to avoid burns or clothing igni-
tion. Fireplace will remain hot for a time after shutdown. Al-
low surfaces to cool before touching.
2. Carefully supervise young children when they are in the room
with fireplace.
3. Do not modify this fireplace under any circumstances. Any
parts removed for servicing must be replaced prior to operat-
ing fireplace.
4. Let fireplace cool before servicing, repairing, or installing ac-
cessories. Only a qualified service person should install, ser-
vice, or repair this fireplace. Have fireplace inspected annu-
ally by a qualified service person.
5. Keep the area around your fireplace clear of combustible mate-
rials, gasoline, and other flammable vapor and liquids. Do not
operate fireplace where these are used or stored. Do not place
items such as clothing or decorations on or around fireplace.
6. Do not connect this fireplace to a chimney system other than a
DESA chimney system.
7. Due to high temperatures, do not locate this fireplace in high
traffic areas or near furniture and draperies.
8. Provide adequate clearances around air openings into the com-
bustion chamber. NEVER obstruct the front openings of the
fireplace or the flow of combustion and ventilation air. Install
in an area providing ventilation and adequate combustion air.
IMPORTANT: Read this owner’s manual carefully and
completelybeforetryingtoassemble,operate,orservice
this fireplace. Improper use of this fireplace can cause
serious injury or death from burns, and fire.
BEFORE YOU BEGIN
Before beginning the installation of your fireplace, read these
instructions thoroughly. This DESA fireplace and its approved
components are safe when installed according to this installation
manual, and operated as recommended by DESA. Unless you use
DESA approved components tested for this fireplace, YOU MAY
CAUSE A FIRE HAZARD!
The DESA warranty will be voided by, and DESA disclaims any
responsibility for the following actions:
A) Modification of the fireplace or any of the components manufac-
tured by DESA unless otherwise permitted in writing by DESA.
B) The use of a fireplace insert or any component part not ap-
proved by DESA in combination with DESA fireplace.
C) Installation and/or operation in a manner other than instructed
in this manual.
D) The burning of any other fuel not tested or approved by DESA
in this wood burning fireplace.
PROPER INSTALLATION is the most important step in ensuring
a safe and continuous operation of this fireplace. Although ground-
ing may not be required by code in your area, it must be electrically
grounded in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70-1990.
This fireplace is intended for installation in accordance with the
NationalFireProtectionAssociationStandardforChimneys,Fire-
places,VentsandSolid-FuelBurningFireplaces,NFPA211,andin
accordancewithcodessuchastheBOCABasic/National Code, the
Standard Mechanical Code, and the Uniform Building Code.
THISFIREPLACEISNOTINTENDEDTO BEUSEDAS
A PRIMARY SOURCE OF HEAT.
NOTE: Installation and repair should be done by a qualified
installer familiar with the fireplace. The fireplace and chimney
systemshouldbeinspected and cleanedbeforeuseandperiodically
thereafterespecially duringheating season to prevent the excessive
buildup of soot and creosote and to ensure a safe operating system.

55253C
4
For more information, visit www.desatech.com
For more information, visit www.desatech.com
SELECTING LOCATION
To determine the safest and most efficient location for your fire-
place, you must take into consideration the following guidelines:
1. The location must allow for all the proper clearances (see Fig-
ure 2).
2. Consider a location where the heat output would not be af-
fected by drafts, air conditioning ducts, windows or doors.
3. A location that avoids the cutting of joists or roof rafters will
make installation easier.
4. If an outside air kit is to be installed, accessibility to outside
combustion air must be considered. This can also be achieved
through a vented crawl space in some cases, for more details
refer to the section on outside air kit installation.
ThetypicalinstallationforaV3610STisaprojectedinstallation,which
allows you to extend the fireplace any distance into the room. A
projectionmaybeidealforanewadditiononanexisting,finishedwall.
Figure 2 - Plan View of Common Location
CLEARANCES
MINIMUM CLEARANCES TO COMBUSTIBLES
Back ............................................. 1" Min.
Adjacent Wall ............................. 12" Min.
Chimney Outer Pipe Surfaces...... 2" Min.
Bottom Of Fireplaces To Floor ..... 0" Min.
CAUTION: Do not block required air spaces with
insulation or any other material. Do not obstruct
effective opening of fireplace with any type of facing
material. Combustible material must not be in con-
tact with the black front face of the fireplace.
Figure 3 - Fireplace Clearances
MANTLE CLEARANCES
Woodwork, such as wood trims, mantles, and other combustible
materials, should not be placed within 9 inches of the effective
opening of this fireplace.
Combustible material above and projecting more than 1 1/2inches
from the fireplace’s front face (see Figure 4, page 5), should not be
placedlessthan12inchesfromtheeffectiveopeningofthefireplace
(Ref: NFPA std.7-3.3.3.).
Mantles or any other combustible material may also come up to the
side edge of the black metal face of the fireplace, but only if the
projectionfromthefrontfacefallswithinthelimitsshowninFigure
5, page 5.
FIREPLACE INSTALLATION
Selecting Location
Clearances
Mantle Clearances
FIREPLACE INSTALLATION

55253C
5
5
For more information, visit www.desatech.com
For more information, visit www.desatech.com
FRAMING
Ifthefireplaceistobeinstalleddirectlyoncarpeting,tile(otherthan
ceramic),oranycombustiblematerialotherthanwoodflooring,the
fireplacemustbeinstalleduponametalorwoodpanelextendingthe
full width and depth of the fireplace.
Construct framing using dimensions shown in Figures 6, 7, and 8,
depending on your particular installation.
Before securing fireplace to prepared framing, the ember protector
(provided) must be placed between hearth extensions (not sup-
plied), and bottom front edge of the fireplace to protect against
glowing embers (see Figure 9, page 6). If the fireplace is to be
installed on a raised platform, a “Z”-type ember protector (not
supplied)mustbefabricatedtofityourrequiredplatformheight(see
Figure 8). The ember protector should be made of 28 gauge
minimum, galvanized sheet metal to prevent corrosion.
Figure 4 - Mantel Clearances
Figure 5 - Mantel Clearances
FIREPLACE INSTALLATION
Continued
Figure 6 - Framing Firebox
Figure 8 - Framing Firebox With “Z” Type Ember Protectors
FIREPLACE INSTALLATION
Mantel Clearances (Cont.)
Framing
FRONT FACE
FIREPLACE FRONT
VIEW
FIREPLACE SIDE
VIEW
3" NOM.
(7.6cm)
9"
(22.8cm)
MIN.
12" MIN.
(30.4cm)
33¡
6" NOM.
(15.2cm)
1
1
/ 2 " MAX.
(3.8cm)
DRYWALL
2" X 4" STUD
COMBUSTIBLE
MATERIALS
39
3
/ 4 "
(101cm)
Min.
43
1
/4"
(109.8cm)
23
5
/
8
"
(60cm)
22
3
/
4
"
(57.7cm)
PLATFORM MUST BE
SOLID, FLAT, AND
FULLY SUPPORTED
"Z" TYPE EMBER
PROTECTOR
(NOT SUPPLIED)
ASREQUIREDBYDESIGN
ASLONGASCEILING
CLEARANCEIS MAINTAINED
44
5
/
8
"
(113.3cm)
53
7
/
16
"
(135.7cm)
MIN.
Figure 7 - Framing Clearances
1" MIN
(2.5cm)
TO COMBUSTIBLES
12 3/8" DIA.
O.D. (31.4cm)
OUTER PIPE
21 5/16"
(54.1cm) 42 5/8"
(108.2cm)
12"
(30.4cm)
24"
(60.9cm)
2" (5cm) MIN.
CLEARANCE
FROM OUTER PIPE
TO COMBUSTIBLES
15" DIA.

55253C
6
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Figure 10 - Nailing Flanges
FIREPLACE INSTALLATION
Continued
HEARTH EXTENSIONS
A hearth extension is required to protect the combustible floor
surrounding your fireplace. You may obtain kit No. HE-3610ST or
you may fabricate your own per the dimensions shown on Figure 10.
Thehearthextensionmustprojectaminimumof16inchesfromthe
front of the fireplace and a minimum of 8 inches beyond each side
of the fireplace opening (see Figure 11).
If a hearth extensions is to be field constructed, it must be made of
noncombustible inorganic material having and effective thermal
conductivity “K” of 0.84 BTU In/Ft2 Hr.F or least at 1.0 inch
thickness.
Thermal conductivity “K” of materials can be obtained from the
manufacturer or supplier or the noncombustible material.
Theminimumrequiredthicknessforanymaterialcouldbeobtained
by the following formula:
K factor x 1.0 inch = Thickness required
0.84
If the hearth extension is to be raised, a “Z” type ember protector
must be used (see Figure 8, page 5, and Figure 12).
Figure 11 - Hearth Extension
Figure 12 - Raised Hearth Extension
FIREPLACE INSTALLATION
Framing (Cont.)
Hearth Extensions
1/2" (1.27cm)
Minimum To
Combustibles
Nailing
Flanges
Prepared
Framing
Nails or
Screws
NONCOMBUSTIBLE
HEARTH EXTENSION
52
1
/
2
" MIN.
(133.3cm)
36
1
/
2
" MIN.
(92.7cm)
8" MIN.
(20.3cm)
16" MIN.
(40.6cm)
8" Max.
K Factor
.84
1
1
/ 2 " Typ.
1
1
/ 2 " Typ.
Noncombustible
Hearth Extension
Noncombustible
Hearth Extension
“Z”Type Ember Protector
Ember Protector
For raised
fireplace, see
section on
framing with a
raised platform.
Figure 9 - Ember Protectors
EMBER
PROTECTOR (TYP. OF 2)
*EMBER PROTECTOR
STRIPS SUPPLIED
1/2" MAX.
(1.2cm)
Securefireplacetopreparedframingatnailingflangeslocatedatthe
sides of fireplace as shown in Figure 10.

55253C
7
7
For more information, visit www.desatech.com
For more information, visit www.desatech.com
OUTSIDE AIR KIT
INSTALLATION
The installation of the outside air kit must be installed during the
rough framing of the fireplace due to the nature of its location.
Outside combustion air can be accessed through an exterior wall or
a vented crawl space (see Figure 13).
CAUTION: Air inlet ducts must not terminate in
attic space.
Themaximumheightfortheairinletabovetheplatformoffireplace
is a minimum of 3 feet below the chimney cap.
For further details on the installation of the outside air kit, please
refer to the instructions included with the air kit.
Figure 13 - Air Kit Installation
Figure 14 - Removing Knockout for Gas Line Installation
FOR UNVENTED ROOM HEATERS, ANSI\IAS\AGA Z21.11.2,
ARE TO BE INSTALLED IN THIS FIREPLACE.
1. To install, remove the knockout indentation on the refractor
(or firebrick) wall located approximately 2 inches above the
refractoryhearth floor.Theknockout indentation mustbe firmly
tapped with any solid object until it is released. Remove frag-
mented portion of refractory (see Figure 14).
2. Removegas line coverplate on rearof fireplace andpull outinsu-
lation from gas line conduit sleeve, save insulation for reuse.
3. Run gas line into the fireplace through the rear at 111/4" from
the floor and through gas line conduit sleeve (if using a raised
platform, add height). Provide sufficient gas line into fireplace
chamber for fitting connection (see Figure 15).
Note: Secureincominggaslinetowoodframingtoproviderigidity
for threaded end.
4. Repack insulation around gas line and into sleeves openings.
Seal any gaps between gas line and refractory knockout hole
with refractory cement or commercial furnace cement. Install
the decorative gas appliance or cap off gas line if desired.
OUTSIDE AIR KIT INSTALLATION
GAS LINE INSTALLATION
Air Inlet
Location
Must Allow
For Bushes
Or Snow
Air Inlet
Termination
GAS LINE INSTALLATION
WARNING: A qualified service person must con-
nect fireplace to gas supply. Follow all local codes.
NOTICE: BEFORE YOU PROCEED, MAKE SURE
YOUR GAS SUPPLY IS OFF!
A gas line may be installed for the purpose of installing a vented or
vent-free decorative gas appliance available through your local
distributor. Use only gas piping approved by local codes. When
installingagasline,ashutoffvalvedesignedforinstallationoutside
the appliance is recommended.
Thegaspipeisintendedforconnectiontoadecorativegasappliances
that operate from natural or propane/LP fuel only: (1), incorporating
anautomaticshutoffdeviceand,(2),complyingwiththeStandardfor
Decorative Gas Appliances for Installation in Vented Fireplace,
ANSIZ21.60-1990.ONLY UNVENTEDGASLOG SETSWHICH
HAVE BEEN FOUND TO COMPLY WITH THE STANDARD
Secure Two Collars With
Duct Tape or Screws
Figure 15 - Running Gas Line
Outside of
Fireplace Gas Line
Conduit
Remove
Insulation
Temporarily
(Do Not
Discard)
Remove
Knockout
Replace Screws After
Removing Gas Line
Cover Plate
Side Firebrick
Finished Side
Refractory
Knockout Plug,
Remove by
Tapping Lightly
With A 1/2" Dowel
Outside of
Fireplace
Side Firebrick
Finished Side
Incoming
1/2" Black
Iron Pipe
Gas Line
Conduit
Repack
Insulation Seal Opening
With Refractory
Cement
Provide Enough
Threaded End For
Fitting Connection

55253C
8
For more information, visit www.desatech.com
For more information, visit www.desatech.com
GAS LINE INSTALLATION
Continued
VENTING INSTALLTION
CHIMNEY PIPE INSTALLATION
The DESA chimney system is a snap-lock, double wall pipe. It
consists of a stainless steel inner flue pipe(s), a galvanized outer
pipe, and a wire spacer.
Each section of pipe comes in lengths of 12, 18, 36, and 48 inches,
but the actual lineal gain for each is measured after each section is
fullyconnected.Linealgainistheactualmeasurablelengthofapart
after two or more parts are connected.
MODEL NO. DESCRIPTION GAIN
V3610ST See-Through" 52 3/4"
Fireplace
48-10DM/48-10TM Flue Pipe 46 5/8"
36-10DM/48-10TM Flue Pipe 34 5/8"
18-10DM/48-10TM Flue Pipe 16 5/8"
12-10DM/48-10TM Flue Pipe 10 5/8"
ETL-10DM Chase Style 1" to 12"
Termination
RTT-10 Round Top Termination 6"
RTL-10DM Round Top Termination 7"
PIPE INSTALLATION
Place pipe assembly (inner and outer with wire spacer) over starter
collar. Inner pipe(s) fit inside inner pipe(s). Outer pipe fits outside
outer pipe.
Begin by aligning hemmed end of inner flue pipe into the inner starting
fluepipeoffireplace.Pushdownuntilhem“snap-locks”withlances.The
outerpipeisjusttheopposite,thefemaleendhasthelances.Continuethe
sameprocedurefortheouterpipe(seeFigure16).Itisimportanttoassure
thejointsbetweenthechimneysectionsarefullylocked.Checkbypulling
chimney upward after locking pipe hem(s). The chimney should not
come apart if properly locked. It is not necessary to add screws to keep
vertical or angled chimney runs together.
Figure 16 - Pipe Connection
WARNING:Theopeningaroundthestartercollaron
topofthefireplacemustneverbeobstructed.Neveruse
blown insulation to fill the chimney enclosure.
FIRESTOP SPACERS
Firestop spacers are required at each point where the chimney
penetrates a floor or ceiling joist space. Their purpose is twofold.
They establish and maintain the required clearance between the
outer pipe and combustible materials, they also serve as a shield
between floors as required by most codes.
Whenpenetratinga floor orceilingat anangle,use firestop spacer
number 30 FS-10DM (see Replacement and Accessory Parts,
back page).
When the pipe passes through a framed opening into a living space
above,afirestopmustbeplacedontheceilingbelow(seeFigure17,
page9).Whenthepipepassesthroughaframedopeningintoanattic
space above, a firestop must be placed on the attic floor above (see
Figure 18, page 9).
CAUTION: When using a decorative appliance,
the damper must be removed or permanently locked
in the open position.
WARNING:AfterensuringthatthegasvalveisON,
test all gas piping and connections for leaks after
installing or servicing. Correct all leaks at once.
WARNING:Neveruseanopenflametocheckfor
a leak. Apply a noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak. Correct all
leaks at once.
GAS LINE INSTALLATION
CHIMNEY PIPE INSTALLATION
PIPE INSTALLATION
FIRESTOP SPACERS
15" (35.1cm)
Galvanized
Outer Pipe
10" (25.4cm)
Stainless Inner
Pipe Lanced
Side Up
Hemmed
Ends
Note: An appropriate DESA hood (see Replacement and Accessory
Parts,page16)mustbe installed whenusinganunvented gas logset.

55253C
9
9
For more information, visit www.desatech.com
For more information, visit www.desatech.com
SUPPORT SECTIONS
Thechimneysupportsectionisa4-inchstrapand12inchlengthofpipe.
Achimney support isrequired every 30feet above thefireplace after a
straight chimney run, or above a return elbow after a straight chimney
run(seeFigure20).This supportisdesignedtorelievetheextraweight
load on the fireplace and elbows when high chimneys are installed.
To achieve desired offset, you may install combinations of 12, 18,
36, and 48 inch lengths of double wall pipe. See Figure 21 and Rise
and Offset Chart below.
VENTING INSTALLTION
Continued
Figure 17 - Firestop Spacer For Living Space
Figure 18 - Firestop Spacer for Attic Space
ELBOW OFFSET INSTALLATION
Chimney weight above offset rests on return elbow. Straps must be
secured with nails to rafters or joists (see Figure 19).
Figure 19 - Elbow Offset
Figure 20 - Chimney Supports Figure 21 - Rise and Offset
FIRESTOP SPACERS
ELBOW OFFSET INSTALLATION
SUPPORT SECTIONS
Existing Ceiling
Frame
Living Space Above Ceiling
Firestop Spacer
Screw (8)
Firestop Spacer
Existing Ceiling
Frame
Attic Space
Above Ceiling
Screw (8)
30 FT.
(9.14m) 30 FT. (9.14m)
Return
Elbow
12S-10DM
Support
Required
2" (5.1cm)
Minimum
A
B
Angled Firestop
Ceiling Support
StrapsReturn
Elbow
RISE AND OFFSET CHART
A B Length of Pipe
(Offset) (Rise) 48 36 18 12
4 3/816 3/8Elbow Set Only
9 1/225 1/41
12 1/230 3/81
14 3/834 2
17 5/839 1/411
21 1/246 1
22 3/448 1/812
26 3/854 7/81
26 3/860 1 1
31 3/463 3/411
34 3/469 1 1
38 5/875 5/82
39 7/877 7/8111
43 3/484 1/211
46 3/487 3/421
48 7/893 3/82
Strap

55253C
10
For more information, visit www.desatech.com
For more information, visit www.desatech.com
FINISHING YOUR CHIMNEY SYSTEM
10 Foot Rule
All chimney terminations must extend a minimum of 3 feet above
the highest point where it passes through the roof, and must be at
least 2 feet above the roof within a 10 foot horizontal span (see
Figure 23).
IMPORTANT: Ifanexposedportionofchimneyisgreaterthan4feet
above the roof line, use support wires to keep chimney secure. The
support wires may be attached to the outer pipe of the chimney with
screws, provided the screws do not penetrate the inner flue pipe.
Figure 23 - 10 Foot Rule
Figure 22 - Typical Offset Installations
Minimum Chimney Height
The minimum chimney height (measured from bottom of fireplace to
fluegasoutlet-endofpipe)is16feetforastraightrun,16feetminimum
for arunwith 1elbowset, and25 feetminimum forarun with2elbow
sets. (A set consists of one starter elbow and one return elbow.)
Uncommon circumstances such as neighboring hills, tall trees, or
strong wind areas can cause down drafts in the chimney system. In
suchcasesgoingbeyond the minimumrecommendedheightwould
be preferable to provide a better draw.
Maximum Chimney Height
The fireplace height approved for any chimney run with this
fireplacesystemis40feetmeasuredfrombottomoffireplacetoflue
outlet-end of pipe. See Figure 24, page 11
Maximum length of pipe between supports is 6 feet of angled run.
A maximum of two 6 foot angled run sections per chimney system
(See Figure 22).
VENTING INSTALLTION
Continued
OFFSET
ELBOW
OFFSET
ELBOW
RETURN
ELBOW
OFFSET
ELBOW
RETURN
ELBOW
RETURN
ELBOW
RETURN
ELBOW
CEILING
SUPPORT
PIPE
V12S-8DM
6’MAX
(15.2cm)
6’MAX
(15.2cm) 6’MAX
(15.2cm)
6’MAX
(15.2cm)
6’MAX
(15.2cm)
6’MAX
(15.2cm)
SUPPORT SECTIONS
FINISHING YOUR CHIMNEY SYSTEM
10 Foot Rule
Minimum Chimney Height
Maximum Chimney Height