Desa SBVBN(D) Quick start guide

FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthefiredepartment.
WARNING: Improper instal-
lation,adjustment,alteration,
service, or maintenance can
causeinjuryorpropertydam-
age. Refer to this manual for
correct installation and op-
erationalprocedures.Foras-
sistance or additional infor-
mationconsult a qualifiedin-
staller,serviceagency,orthe
gas supplier.
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property
damage, personal injury, or loss of life.
FOR YOUR SAFETY
Donotstoreorusegasolineorotherflammablevaporsand
liquids in the vicinity of this or any other appliance.
Installation and service must
be performed by a qualified
installer, service agency, or
the gas supplier.
IMPORTANT: This B-vent burner system must be installed into approved DESA cast iron stove bodies,
models SCIVFC, PSCIVFC, and VH series ONLY. See page 3 of this manual.
This appliance may be installed in an aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance
is not convertible for use with other gases, unless a certified kit is used.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
CAST IRON STOVE AND B-VENT
(FREESTANDING FIREPLACE HEATER)
BURNER SYSTEM
OWNER’S OPERATION AND INSTALLATION MANUAL
For more information, visit www.desatech.com
For more information, visit www.desatech.com
Save this manual for future reference.
Save this manual for future reference.
NATURAL GAS BURNER SYSTEM SBVBN(D)
PROPANE/LP GAS BURNER SYSTEM SBVBP(D)
REMOTE READY
SCIVFC/PSCIVFC
SERIES STOVE VH SERIES STOVE

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
2
SAFETY INFORMATION
1. This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases unless a certified kit is used.
2. For propane/LP burner system, donot place propane/LPsupply
tank(s) inside any structure. Locate propane/LP supply tank(s)
outdoors. To prevent performance problems, do not use pro-
pane/LP fuel tank of less than 100 lbs. capacity.
3. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions
• if you cannot reach you gas supplier, call the fire department.
4. Never install the stove
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable ob-
jects are less than 42" from the front, top, or sides of the
stove with burner system
• in high traffic areas
• in windy or drafty areas
IMPORTANT: Read this owner’s manual carefully
andcompletelybeforetryingtoassemble,operate,or
service this stove and burner system. Improper use
of this stove and burner system can cause serious
injuryordeathfromburns,fire,explosions,electrical
shock, and carbon monoxide poisoning.
WARNINGS
DANGER: Carbon monoxide poisoning may lead
to death!
This stove with burner system is a vented product. This stove with
burner system will not produce any gas leakage into your home if
properly installed. This unit must be properly installed by a qualified
service person. The glass door must be properly seated and sealed. If
thisunitisnotproperlyinstalledbyaqualifiedservicepersonwithglass
door properly seated and sealed, gas leakage can occur.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the burner system may not have been installed
properly. Get fresh air at once! Have stove with burner system
inspectedandservicedbyaqualifiedserviceperson.Somepeopleare
more affected by carbon monoxide than others. These include preg-
nantwomen,peoplewithheartorlungdiseaseoranemia,thoseunder
the influence of alcohol, and those at high altitudes.
WARNING: Any change to this stove or burner
system or its controls can be dangerous.
WARNING:Thisproductcontainsand/orgenerates
chemicals known to the State of California to cause
cancer or birth defects, or other reproductive harm.
NaturalandPropane/LPGas:Naturalandpropane/LPgasesare
bothodorless.Anodor-makingagent is added to eachofthesegases.
Theodorhelpsyoudetectagasleak.However,theodoraddedtothese
gases can fade. Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this stove with B-vent burner system.
TABLE OF CONTENTS
SAFETY INFORMATION ........................................................... 2
PRODUCT IDENTIFICATION ..................................................... 3
LOCAL CODES........................................................................... 4
PRODUCT FEATURES .............................................................. 4
PRE-INSTALLATION PREPARATION ........................................ 4
CAST IRON STOVE AND B-VENT BURNER
SYSTEM ASSEMBLY ............................................................ 5
VENTING INSTALLATION .......................................................... 9
TROUBLESHOOTING VENTING PROBLEMS ........................ 12
CAST IRON STOVE AND B-VENT BURNER
SYSTEM INSTALLATION .................................................... 12
OPERATING STOVE WITH B-VENT BURNER SYSTEM........ 19
INSPECTING BURNERS.......................................................... 21
CLEANING AND MAINTENANCE ............................................ 22
TROUBLESHOOTING .............................................................. 23
REPLACEMENT PARTS .......................................................... 26
TECHNICAL SERVICE ............................................................. 26
WIRING DIAGRAM ................................................................... 26
SERVICE HINTS....................................................................... 26
SPECIFICATIONS .................................................................... 27
ILLUSTRATED PARTS BREAKDOWNAND PARTS LIST ....... 28
ACCESSORIES ........................................................................ 32
OWNER’S REGISTRATION FORM.......................................... 33
WARRANTY INFORMATION...................................... Back Cover
TABLE OF CONTENTS
SAFETY INFORMATION

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
3
3
20. Do not use a blower insert, heat exchanger insert, or other ac-
cessory not approved for use with this stove.
21. Do not operate burnersystemwithglass door removed,cracked,
or broken.
22. This heater must be properly connected to a vent system. This
heater is equipped with a vent safety shutoff system.
23. Provide adequate clearances to air openings.
5. This stove reaches high temperatures. Keep children and adults
awayfromhot surfacestoavoid burns orclothingignition. Stove
will remain hot for a time after shut-down. Allow surfaces to
cool before touching.
6. Carefully supervise young children when they are in the room
with stove.
7. Do not modify this stove or burner system under any circum-
stances.Any parts removed for servicing must bereplacedprior
to operating burner system.
8. Turn burner system off and let cool before servicing, installing,
or repairing. Only a qualified service person should install, ser-
vice,orrepair this stoveorburner system.Havestoveand burner
system inspected annually by a qualified service person.
9. Youmust keepcontrolcompartments, burners,andcirculating air
passages clean. More frequent cleaning may be needed due to
excessive lint and dust from carpeting, bedding material, pet hair,
etc. Turn off the gas valve and pilot light before cleaning stove or
burner system.
10. Have venting system inspected annually by a qualified service
person. If needed, have venting system cleaned or repaired.
See Cleaning and Maintenance, page 22.
11. Keep the area around your stove clear of combustible materi-
als, gasoline, and other flammable vapor and liquids. Do not
run burner system where these are used or stored. Do not place
items such as clothing or decorations on or around stove.
12. Do not use this stove to cook food or burn paper or other objects.
13. Never place anything on top of stove.
14. Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this burner system. Use only the gas type indicated on burner
system nameplate.
15. This appliance, when installed, must be electrically grounded
inaccordancewithlocalcodesor, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, or the Ca-
nadian Electrical Code, CSA C22.1.
16. Do not obstruct the flow of combustion and ventilation air in
any way. Provide adequate clearances around air openings into
the combustion chamber along with adequate accessibility
clearance for servicing and proper operation.
17. Do not install stove with burner system directly on carpeting,
vinyltile, oranycombustiblematerialother thanwood.Thestove
must set on a metal or wood panel extending the full width and
depth of the stove.
18. Do not use stove or burner system if any part has been ex-
posed to or under water. Immediately call a qualified service
person to arrange for replacement of the unit.
19. Do not operate burner system if any log is broken.
SAFETY INFORMATION
Continued
PRODUCT IDENTIFICATION
Blower with
Adjustment
Knob
(Optional
Installation)
Pilot
Assy
Burner
Vent Opening
Glass
Door
Assy
Glowing
Embers
Grate
Assembly
Rear
Cover
Cast Iron
Stove Body
Cast Iron
Stove Body
Piezo Ignitor Control Valve
Log Set
Lava
Rock
Figure 1 - DESA B-Vent Burner System Shown Installed in
ApprovedDESACastIronStoveBodyModelsSCIVFC,PSCIVFC,
and VH Series Only (Amity™Model Shown)
SAFETY INFORMATION
PRODUCT IDENTIFICATION

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
4
LOCATION AND SPACE REQUIREMENTS
DeterminethesafestandmostefficientlocationforyourDESAB-vent
castironstove.Makesurethatraftersandwall studs are not in the way
of the venting system. Choose a location where the heat output is not
affected by drafts, air conditioning ducts, windows, or doors. Figure 2
shows some common locations. Read all venting information in this
manual.Beawareofallrestrictionsandprecautionsbeforedecidingthe
exact location for your stove.
PRE-INSTALLATION
PREPARATION
6 "
4 "
Front
4"
36"
from
Front
42"
Ceiling
Floor
from
Back
Wall
29"
Figure 3 - Clearances for Standard Installation
On Wall with Vertical
Termination Through Ceiling Corner Installation with Vertical
Termination Through Ceiling
Figure 2 - Common Stove Locations
WARNING: A qualifiedinstalleror service person
mustinstallstoveandburnersystem.Followalllocal
codes.
CAUTION: This stovewithburner system creates
warm air currents. These currents move heat to wall
surfaces next to stove. Installing stove next to vinyl
orclothwallcoveringsoroperatingstovewithburner
system where impurities (such as, but not limited to,
tobaccosmoke,aromaticcandles,cleaningfluids,oil
or kerosene lamps, etc.) in the air exist, may discolor
walls or cause odors.
Install and use stove and burner system with care. Follow all local
codes. In the absence to local codes, use the current National Fuel
GasCode ANSIZ223.1/NFPA54*(USA)orthecurrentCAN/CGA-
B149[.1 or .2] Installation Codes (Canada).
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
LOCAL CODES
PRODUCT FEATURES
OPERATION
This B-vent cast iron stove with burner system is clean burning and
vents vertically. Heat is generated by both realistic flames and
glowing embers. When used without the blower accessory, the
stove with burner system requires no electricity making it ideal for
emergency backup heat.
PIEZO IGNITOR
This burner system has a piezo ignitor. This system requires no
matches, batteries, or other sources to light burner system.
When deciding the location of your stove, follow these rules:
1. Do not connect this stove and burner system to a chimney flue
serving a separate solid-fuel burning fireplace or appliance.
2. Due to high temperatures, do not locate this stove in high traf-
fic areas or near furniture or draperies.
3. Proper clearances must be maintained, see Figure 3 below and
Figure 4 on page 5.
4. This stove is a freestanding unit designed to set directly on the
floor. If your stove is to be installed directly on carpeting, vi-
nyl tile, or any combustible material other than wood, it must
be installed on a metal or wood panel extending the full width
and depth of the stove. See Figure 5, page 5.
LOCAL CODES
PRODUCT FEATURES
Operation
Piezo Ignitor
PRE-INSTALLATION PREPARATION
Location and Space Requirements

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
5
5
4"
4"
Figure 4 - Clearance for Corner Installation
Figure 5 - Stove With Burner System Bottom Dimensions
PRE-INSTALLATION
PREPARATION
Continued
CAST IRON STOVE AND B-VENT
BURNER SYSTEM ASSEMBLY
STOVE BODY ASSEMBLY
1. Lift off corrugated box enclosing stove body crating.
2. Remove all screws fasteningthewoodframeenclosure.Spread
woodframeopenandliftaway from plastic-bagged stove body.
The bottom pieces of pallet wood will remain bolted to the
stove body.
3. Remove plastic bag from stove body.
4. Locate the product identification label on the back panel (see
Figure 6) and record the model number and 7 digit serial num-
ber in the space provided in the back of this owner’s manual.
Retain this operation and installation manual for future refer-
ence and warranty.
5. Remove back panel from stove and discard (see Figure 6). Use
an adjustable wrench or a 10 mm socket. Remove six (6) bolts
and washers. Keep bolts and washers to reattach rear cover.
6. Remove all contentsfrominsidestovecavity. Contents include:
(1) - Stove bottom (Discard - Not used with this application)
(4) - Legs with leg leveler bolts
(1) - Bottom door
(3) - Top grates
(1) - Hardware kit bag with fasteners
Figure 6 - Removing Back Panel
Bolt
Product
Identification Label
with Model and
Serial Numbers
Back Stove
Panel
Pallet
Wood
Bolted to
Bottom of
Stove
Body
Figure 7 - Laying Down Stove On Side
Front of
Stove
Unit
Top of Stove Unit Front of
Stove Unit
Top of
Stove
Unit
Drop
Cloth/
Blanket
7. Carefully lay stove body on back to attach bottom components to
stove body (see Figure 7). Rest stove on drop cloth or blanket to
avoid scratching stove edges.
8. Remove remaining pallet wood attached to bottom of stove
body (see Figure 8). Use an adjustable wrench to remove bolts.
9. Fasten each leg to stove with four (4) M8 x 1.25 - 20mm bolts.
Use a flat washer and lock washer with each bolt. Tighten bolts
into threaded holes on stove body (see Figure 9 and Figure 10
on page 6). Use an adjustable wrench or a 12mm socket.
Figure8-RemovingPalletWoodFromTheBottomofTheStove
Pallet Wood
Bolt Pallet
Wood
Bottom Of
Stove Unit
Front
Figure9-LocatingThreadedHolesforLegsandDoorAttachment
Leg Hole
Front
Door Hinge
Step Bolt Hole Door Catch Bolt
With Adjustable
Hex Nuts Hole
Bottom Of
Stove Unit
PRE-INSTALLATION PREPARATION
Location and Space Requirements (Cont.)
CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY
Stove Body Assembly
26 1/4"
19 1/2"
Front

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
6
CAST IRON STOVE AND B-VENT
BURNER SYSTEM ASSEMBLY
Continued
Figure11-Attaching Stove Door
Step
Bolt
Door Hinge
Threaded
Hole
Stove Door
Bolt Shoulder
Adjusting
Nut
Bolt Stop
Catch Bolt
Door Claw
Door
Figure 12 - Catch Bolt and
Door Claw Orientation
10. Attach stove door by inserting step bolt through door hinge
pivot hole and into threaded hole in stove body (see Figure 11
and Figure 9 on page 5). Use an adjustable wrench or a 12mm
socket to fasten step bolt. Tighten step bolt until snug. Make
sure door moves freely.
11. Install door catch bolt (M8 x 1.25-55mm with two M8 hex
nuts) into threaded hole on stove body (see Figure 9, page 5).
Use an adjustable wrench or a 12mm socket. The catch bolt
has two hex nuts attached to it (see Figure 12). The top nut is a
bolt stop and the bottom nut is for door leveling adjustment.
12. Check general catch bolt alignment with door claw. Make fi-
nal adjustment and door leveling after stove is in normal stand-
ing position.
13. Carefully lift stove back up on its four attached legs.
Removing Front Surround Panel
Remove 2 bolts from bottom of stove and set aside. Remove bolt
from the top of the stove to remove the front panel assembly (see
Figure 13).
Figure 10 - Attaching Stove Legs (Amity™Model Shown)
Bottom Of
Stove Unit
Leg
Bolt
Washers
Removing Screen (Optional)
Amity Models
1. Lay the front panel assembly face down on a protected sur-
face. Remove the two screws that hold the front plate onto the
front surround plate (see Figure 14). Save these screws.
2. Remove the screws and washers that hold the screen onto the
front surround plate. Discard these screws, washers, and screen
(see Figure 14).
3. Replace the two screws from step 14 to reassemble the front
plate and the front surround plate. Set this assembly aside un-
til burner system has been installed, logs have been placed
inside of burner system, and glass door to burner system insert
has been replaced.
Victor Hearth Models
1. Lay the front panel assembly face down on a protected sur-
face. Remove the screws and washers that hold the screen onto
the front surround plate. Discard these screws, washers, and
screen (see Figure 14).
2. Set this assembly aside until burner system has been installed,
logs have been placed inside of burner system, and glass door
to burner system insert has been replaced.
Figure 13 - Removing Front Assembly (Amity™Model Shown)
Front
Assembly
Bolt
Stove Body
Figure 14 - Removing Screen from Front Assembly
Screws
Front
Surround
Plate
Front Plate
Screen
Screw with
Washer
CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY
Stove Body Assembly (Cont.)
Amity™Model Victor Hearth™Model
Screw with
Washer
Screen
Front Surround
Plate and
Doors

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
7
7
CAST IRON STOVE AND B-VENT
BURNER SYSTEM ASSEMBLY
Continued
INSTALLING B-VENT BURNER SYSTEM INTO
STOVE BODY
1. Carefully lift burner system and place into stove body from
the rear of stove.
2. Place the left and right grate tops into the top of stove body. Dis-
card center grate top of stove and replace with center grate top
provided with burner system.
Figure 15 - Installing Burner System Into Cast Iron Stove Body
Cast Iron
Stove Body Burner
System
Right Top Grate
Center Top Grate
(Included with
Burner System)
Left Top
Grate
NOTICE: If installing blower in an existing stove
burner system with gas connections, shut off gas
supply and disconnect heater from gas supply. Con-
tact a qualified service person to do this.
INSTALLING OPTIONAL BLOWER
ACCESSORY
1. Remove 4 hex screws securing rear cover to back of stove body
(see Figure 16).
2. Separate bottom cover from rear cover by loosening the 8
mounting screws (see Figure 16).
3. Align the holes in the top mounting tabs of blower with the
holes in wall of rear cover. Using the 4 screws provided, mount
blower and tighten screws securely (see Figure 17).
4. Thermostat Blower Only: Attach thermal switch and bracket to
insiderearcoverwallwithtwohexheadscrewsprovidedasshown
in Figure 17.After securing bracket to rear cover, carefully bend
along existing bend line on bracket to almost a 90° angle (see
Figure17).This willallowthermalswitchtobepositionedagainst
stove rear wall and sense temperature when in operating mode.
Figure16-RemovingRearCoverandBottomCoverfromStove
Body
Stove Body
Rear Cover
Bottom Cover
Mounting
Screws
Mounting
Screws
Hex Screws
Figure 17 - Blower Assembly, Speed Control, and Thermal
Switch Locations
Speed
Control
Blower
Control
Knob Locknut
Blower
Assembly
Thermal Switch
and Bracket
Control Shaft
TOP VIEW
Mounting Holes
Mounting Holes
Screws
CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY
Installing B-Vent Burner System Into Stove Body
Installing Optional Blower Accessory

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
8
INSTALLING REAR COVER
1. Place rear cover behind stove body. Rear cover will rest on the
bottom ledge of the stove body.
2. Using hex screws provided, attach rear cover to back of stove
body. See Figure 19. IMPORTANT: This rear cover must be
securely in place before venting pipes are installed.
3. Open lower door panel. The valve is attached to the underside
of the burner system assembly.
4. Connect or reconnect gas supply, see Connecting Stove/Burner
System to Gas Supply on page 14.
Figure 19 - Installing Rear Cover (Shown with Optional Blower
Accessory)
Rear Cover
(Shown with
Optional
Blower)
Hex Screws
Blower Power Cord
5. Place speed control on left inside of rear cover and push the
plastic control shaft through opening (see Figure 17, page 7).
6. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until
tight against the side of rear cover. Place control knob provided
onto shaft.
7. Place the green ground wire between the bottom hole on the
blower assembly and the hex screw and tighten (see Figure 18).
8. Connect the blue wire on the blower assembly to one side of
the thermal switch (see Figure 18).
9. Connect the black wire to the other side of the thermal switch
(see Figure 18).
10. Connect the white wire to the other terminal on the blower mo-
tor assembly (see Figure 18). Make sure the thermal switch has
been properly installed to fit against back of burner system in-
sert after the rear cover assembly has been reinstalled.
11. Make sure all wire connections to terminals on blower motor
and thermal switch are securely attached and that the screw
retaining the green ground wire is tight.
12. Check to make sure that the power cord is completely clear of the
blowerwheelandthatthereareno foreignobjectsinblowerwheel.
WARNING:Nevertouchtheblowerwheelwhilein
operation.
WARNING: Failure to position the parts in accor-
dance with supplied diagrams or failure to use only
partsspecificallyapprovedwiththisheatermayresult
in damage or personal injury.
WARNING: A qualifiedinstalleror service person
mustconnectburnersystemtogassupply.Followall
local codes.
Figure 18 - Blower Wiring Layout
13. Peel off the backing paper and stick the supplied wiring dia-
gram decal on the inside of rear cover as shown (see Figure 18).
14. Reattach bottom cover to rear cover with 8 screws (see Figure
16, page 7). Make sure that you don’t pinch any wires during
reassembly. Route power cord through plastic bushing in bot-
tom of rear cover.
CAST IRON STOVE AND B-VENT
BURNER SYSTEM ASSEMBLY
Continued
Green Ground Wire
Wiring
Diagram
Decal
Speed
Control
Black
Wire
White
Wire
Blue Wire
Power Cord (Route Through
Plastic Bushing in Bottom
Cover When Assembled)
Screw
Thermal
Switch
CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY
Installing Optional Blower Accessory (Cont.)
Installing Rear Cover

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
9
9
INSTALLATION PRECAUTIONS
Consultlocalbuildingcodesbeforebeginningtheinstallation.Only
a qualified service person should install venting system. The in-
staller must follow these safety rules:
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
• Installation of any damaged venting component
• Unauthorized modification of the venting system
• Installationofanycomponentpartnotmanufactured or approved
by DESA
• Installation other than as instructed by these instructions
Your DESA stove with B-vent burner system is approved for use
withanylistedgasvent.Alistedgasventisafactorymadeandlisted
systemdesigned,andinstalledexclusivelyforremovingproductsof
combustion, excess air, and dilution air resulting from burning fuel
gas. Metal vents, the most common type of vent, employ double
wall construction enclosing an insulating air space. This air space
both helps keep flue gases warm and reduce heat transferred to
nearby combustibles. This appliance is equipped with a safety
control system designed to protect against improper venting of
combustion products.
It is very important that the venting system maintain its balance
between the combustion air intake and the flue gas exhaust. Certain
limitationsapplytoventconfigurationsandmustbestrictlyfollowed.
VENTING INSTALLATION
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
dosocouldresultinseriousinjury,propertydamage,
or loss of life. Operation of improperly installed and
maintained venting system could result in serious
injury, property damage, or loss of life.
NOTICE: Failure to follow these instructions will void
the warranty.
WARNING: This gas stove with burner system
and vent assembly must be vented directly to the
outside. The venting system must NEVER be at-
tached to a chimney serving a separate solid fuel
burning appliance.
TYPE B-VENT INSTALLATION
(Listed B-0 or Greater)
Before beginning installation be sure that the overall height and gas
ventsizeconformtobuildingcoderequirements.Gasventsextending
VENTING INSTALLATION
Installation Precautions
Type B-Vent Installation
Figure 20 - Typical B-Vent Installation
Round Top
Storm Collar
Flashing Roof Support
25mm (1") Clearance to
Combustible Material
Firestop
Spacer
Keep Electrical Wires and
Building Insulation Away from
Gas Vent and Out of the
Required Air Space
Enclosure
Wall
Gas Vent
Length
25mm (1") Clearance to
Combustibles
Support
Plate
Adjustable
Length
throughpitchedroofscanextendaminimumheightofatleast600mm
(2')higherthanany obstruction within3m(10').Gas vents extending
throughflatroofsarerequiredtoextendatleast600mm(2')abovethe
roof and at least 600 mm (2') higher than any portion of the building
or adjoining building within 3m (10') of the gas vent.
• In absence of local codes, follow Section 7.0 of the current Na-
tional Fuel Gas Code NFPA 54/ANSI Z223.1 and the Natural
Gas Installation Code - vent sizings for Category I systems us-
ing double wall B-1 vent pipe.
• Where the gas vent extends through accessible spaces, it should
be enclosed to avoid personal contact and damage. Enclosure
walls should have a fire rating equal to or greater than the floors
through which the gas vent passes except in single or two-fam-
ily dwellings.
• Situate the gas vent in the structure so that it can be installed
without cutting joists, sills, plates, or major load bearing parti-
tions or members. It is also important to locate the base of the
gas vent as near as possible to the heating appliance.
• This burner system must be properly connected to a venting system.
This burner system is equipped with a vent safety shutoff system.
• Use only vents labeled "FOR EXTERIOR USE" above the
roofline.
• Consult the authority having jurisdiction to select the correct
gas vent diameter.Avoid using a larger than necessary diameter.

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
10
WARNING: Installation should only be made by
qualified persons who are familiar with the safety
procedures required for the installation of the prod-
uct, who are equipped with the proper tools and
testing instruments, and who have achieved proper
certification of licensing. Installations made by un-
qualified persons can result in the risk of injury or
electrical shock which can be serious or even fatal.
INSTALLATION OF LISTED B-1 VENT
VENTING INSTALLATION
Continued
Figures 21 through 23 show other options for the gas vent. When
venting through a side wall your vent pipe must have the proper
temperaturerating(seeFigure23). Manufacturer's clearances must
alsobemaintained.Consulttheauthorityhavingjurisdictioninyour
area regarding venting through side wall.
Figure 21 - Vertical
Venting Through Ceiling
Using Two 90
º Elbows
(Amity™Model Shown)
Figure 22 - Vertical Venting
ConfigurationThrough Chimney
(Amity™Model Shown)
Figure23-VentingThroughaSideWall(Amity™ModelShown)
INSTALLING VENT SYSTEM IN A CHASE
Achaseisaverticalbox-likestructurebuilttoencloseventingthatruns
alongtheoutsideofabuilding.Achaseisnotrequiredforsuchventing.
NOTICE: Treatment of firestops and construction of
the chase may vary from building type to building
type. These instructions are not substitutes for the
requirements of local building codes. You must fol-
low all local building codes.
Note: When installing in a chase, you should insulate the chase as
you would the outside walls of your home. This is especially
importantincold climates.Minimumclearance between ventpipes
and combustible materials such as insulation is 1".
CHECKING VENT CAPACITY
Completeallgas piping, electrical,andvent connections. Afteradjust-
ing the burner system and lighting the main burners, allow a couple of
minutes for warm-up. Hold a lighted match just under the rim of the
drafthoodreliefopening.Properventingwilldrawtheflametowardor
intothedrafthood.Improperventing,indicatedbyescapeorspillageof
burnedgas,willcausematchtoflickerorgoout.Smokefromacigarette
will also be pulled into the draft hood if the vent is drawing properly.
Figure 24 - Test for Proper Venting
VENTING INSTALLATION
Installation of Listed B-1 Vent
Installing Vent System In A Chase
Checking Vent Capacity

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
11
11
VENTING INSTALLATION
Continued
CHIMNEYS
• Complete familiarity with chimney condition, height, size, clear-
ance to combustibles and other factors is essential.
NOTICE: Consult the authority having jurisdiction
in your area regarding masonry chimney venting
applications.
NOTICE: A complete chimney inspection by a quali-
fied person should be performed.
• Appliances using B-vent connectors to vent into a masonry or
factory-built chimney should not exceed 1 1/2feet in length for
every inch of connector diameter (3" vent connector has a maxi-
mum41/2foot length;5"connector hasmaximum7 1/2foot length).
• Oversized chimneys should be relined with appropriate listed
relining systems.
• Cleanout access may be required.
NOTICE: Consult the authority having jurisdiction in
your area regarding listed chimney liner venting
applications.
WARNING:Operation of improperly installedand
maintained venting system could result in serious
injury, property damage, or loss of life.
RELINING SYSTEMS
• Suitabilityand approvalofreliningmaterialsshould bedetermined.
• Condition, size, height, and termination of the chimney to
be relined must be determined.
• No substitution of components should be made.
• Joints and connectors should be made according to
manufacturer’s instructions.
Figure 25 - Straight
Installation into Masonry
Chimney
Figure 26 - Typical Straight
InstallationwithListedChimney
Liner
HIGH ALTITUDE INSTALLATION
YourDESAB-ventburnersystemhasbeenCSAtestedandapproved
foroperationataltitudes inthe USAfrom0-2000feetandinCanada
from 0-4500 feet.
Wheninstallingthisburnersystematanelevationabove2000feet(in
the USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet above sea level. Check with your local gas company for
proper orifice size identification and proper orifice for your location.
When installing this stove and burner system at an elevation above
4500 feet (in Canada), check with local authorities.
For assistance with any high altitude installation contact DESA’s
Technical Service Department at 1-866-672-6040.
VENTING INSTALLATION
Chimneys
Relining Systems
High Altitude Installation

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
12
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
CHECK GAS TYPE
Use proper gas type for the burner system unit you are installing. If
you have conflicting gas types, do not install burner system. See
dealer where you purchased the stove and burner system for proper
burner system according to your gas type.
IMPORTANT:Ifinstallinggasconversionkit,dosoatthistime.
Be sure to follow all installation instructions included with
conversion kit.
NOTICE: This burner system is intended for use as
supplemental heat. Use this burner system along
with your primary heating system. Do not install this
stoveandburnersystemasyourprimaryheatsource.
If you have a central heating system, you may run
system’s circulating blower while using heater. This
will help circulate the heat throughout the house. In
the event of a power outage, you can use this burner
system as your primary heat source.
TROUBLESHOOTING
VENTING PROBLEMS
Most venting problems are caused by incorrect vent sizing, im-
proper installation, or inadequate air supply. A preliminary check
for a field problem might include:
• Checking the vent sizing according to manufacturer’s specifica-
tions, appliance input, and venting configuration
• Examining the entire venting system for faults such as discon-
nected joints for damaged vent sections
• Making sure vent and air openings are not obstructed
If these procedures do not reveal the source of the problem, trouble-
shooting may include attention to common venting problems.
FLUE GAS SPILLAGE
Spillage occurs when flue gases cannot exit the vent system and
back up into the dwelling. A primary symptom of appliances
equipped with a Vent Safety Shutoff System (flue spill switch) is
unexplained appliance shutoffs. Other symptoms of flue gas spill-
age at the draft hood include condensation on walls and windows
and/or noticeable odors. Spillage may also result in the release of
carbon monoxide, a colorless, odorless, highly toxic gas. A simple
spillagetestcanbeconductedifspillageissuspected.SeeChecking
Gas Connection, pages 14 and 15.
CAUSES OF SPILLAGE AND CORRECTIVE
ACTION
Incorrect Vent Sizing
If the vent is too small or too short, spillage may occur. If the vent
is too large, excessive dilution air may cool flue gases and reduce
draft, causing spillage. The vent cap size should also be checked.
Check manufacturer’s instructions, appliance input rating, and
appropriate sizing tables.
Venting Condition
Loose joints can affect draft and cause spillage. “Mashed” vent
sectionsanddamagedventcapscanrestrictflowandcausespillage.
Examine and replace as needed.
Obstructions
Small animals or birds may get into and block the vent or draft hood
outlet.Dust,lint, andforeignobjectsmay obstructairinlets. Remove
obstructions and clean openings.
Lateral Run
Lengthyhorizontalornon-verticalrunscauseresistancetoflowand
may reduce draft enough to cause spillage. The pitch of lateral runs
can also be a problem; lateral runs should be pitched 1/4" rise per
foot of horizontal run from the appliance to the vent.
Elbows
Toomanyelbowscauseexcessiverestrictionofflowandmayresult
in spillage. Usually, two 90º turns can be tolerated in a properly
sized venting system. More than two may cause problems and
necessitate changing the system.
Negative Pressure in the Dwelling
Anextremelytight house maynotsupplyadequate combustionand
ventingair. Useofmechanicalexhaustsuch asa dryerventorrange
vent may worsen the problem. An air exchange system must be
installed in the dwelling to correct this problem.
Flue Gas Cooling
Venting exposed to extremely cold temperatures or venting of
single wall construction loses heat needed to maintain draft; mas-
sive masonry chimneys absorb needed heat. If the flue gases cool
excessively, draft is reduced and spillage may result. Use proper
materials, insulate and protect properly, reline when necessary.
Down Drafts
In certain wind conditions and in certain relationships with nearby
structures and objects, high pressure conditions may affect draft
negatively.Relocatetheventcap,raiseitsheight,oruseanapproved
high wind cap.
TROUBLESHOOTING VENTING PROBLEMS
Flue Gas Spillage
Causes of Spillage and Corrective Action
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Check Gas Type

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
13
13
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in cer-
tain areas. Check your local codes. Use pipe of 1/2"
diameter or greater to allow proper gas volume to
burner system. If pipe is too small, undue loss of
volume will occur.
Installation Items Needed
Before installing stove and burner system, make sure you have the
items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by lo-
cal codes) (not provided)
* A CSA design-certified equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to test gauge connection. Purchase
the CSAdesign-certifiedequipmentshutoffvalvefromyourdealer.
For propane/LP connections only, the installer must supply an
external regulator. The external regulator will reduce incoming gas
pressure.Youmustreduceincominggaspressuretobetween11and
14 inches of water. If you do not reduce incoming gas pressure,
heaterregulator damagecouldoccur.Installexternalregulatorwith
the vent pointing down as shown in Figure 27. Pointing the vent
down protects it from freezing rain or sleet.
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
Installation must include an equipment shutoff valve, union, and
plugged1/8"NPTtap.LocateNPTtapwithinreachfortestgaugehook
up. NPT tap must be upstream from burner system (see Figure 28).
Checkyourbuildingcodesforanyspecialrequirementsforlocating
equipment shutoff valve to stoves.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged burner system valves.
WARNING:Usepipejointsealantthatisresistant
to liquid petroleum (LP) gas.
Figure 27 - External Regulator with Vent Pointing Down
(Propane/LP Only)
Propane/LP
Supply Tank
External
Regulator
Vent Pointing
Down
Figure 28 - Gas Connection
* The CSA design-certified equipment shutoff valve may be sup-
plied with the appliance or you can purchase it from your dealer.
CSA Design-Certified
Equipment Shutoff Valve with
1/8" NPT Tap*
3" Minimum
LP - From External
Regulator (11" W.C. to
14" W.C. Pressure)
Approved Flexible
Gas Line
Cap Pipe Nipple Tee Joint
Sediment Trap/Drip Leg
Natural - From Gas
Meter (5" W.C. to 10.5"
W.C. Pressure )
INSTALLING GAS PIPING TO STOVE
LOCATION
WARNING:Aqualifiedinstalleror service person
mustconnectburnersystemtogassupply.Followall
local codes.
CAUTION: For propane/LP units, never connect
burnersystemdirectlytothepropane/LPsupply.This
burner system requires an external regulator (not
supplied). Install the external regulator between the
burner system and propane/LP supply.
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Installing Gas Piping to Stove Location

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
14
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Figure 30).
2. Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas burner system or opening
maingasvalvelocatedonorneargas meterfornatural gasburner
system, or using compressed air.
3. Checkalljointsfrompropane/LPsupplytankorgasmetertoequip-
ment shutoff valve (see Figure 31 for propane/LP or Figure 32 for
natural, page 15).Apply noncorrosive leak test solution to all gas
joints. Bubbles forming show a leak. Correct all leaks at once.
Figure 30 - Equipment Shutoff Valve
ON
POSITION
OFF
POSITION
Open
Closed
Equipment
Shutoff Valve
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1. Disconnectappliance with its appliance main gas valve (control
valve) and equipment shutoff valve from gas supply piping
systems. Pressures in excess of 1/2 psig (3.5 kPa) will damage
burner system gas regulator.
2. Cap off open end of gas pipe where equipment shutoff valve
was connected.
3. Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas burner system or opening
maingasvalvelocatedonorneargas meterfornatural gasburner
system, or using compressed air.
4. Check all joints of gas supply piping system.Apply noncorro-
sive leak test solution to all gas joints. Bubbles forming show
a leak. Correct all leaks at once.
5. Reconnect burner system and equipment shutoff valve to gas
supply. Check reconnected fittings for leaks.
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections,
internal and external to unit, for leaks after installing
or servicing. Correct all leaks at once.
WARNING: Never use an open flame to check for
a leak. Apply noncorrosive leak test solution to all
gas joints. Bubbles forming show a leak. Correct all
leaks at once.
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower door panel.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to burner system (see Figure 29). Route flexible
gas supply line and attach to valve.
3. Check all gas connections for leaks. See Checking Gas
Connections, column 2.
CONNECTING STOVE/BURNER SYSTEM TO
GAS SUPPLY
To Flare Fitting on
Control Valve
Flexible Gas Line from
Equipment Shutoff Valve
Provided by Installer
Equipment
Shutoff Valve
To Gas Supply
(Natural)
To External Regulator
(Propane/LP)
Figure 29 - Flexible Gas Line
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
We recommend that you install a sediment trap/drip leg in supply
line as shown in Figure 28, page 13. Locate sediment trap/drip leg
where it is within reach for cleaning. Install in piping system
between fuel supply and burner system. Locate sediment trap/drip
legwheretrappedmatterisnotlikelytofreeze.Asedimenttraptraps
moistureandcontaminants.Thiskeepsthemfromgoingintoburner
system gas controls. If sediment trap/drip leg is not installed or is
installed wrong, burner system may not run properly.
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Installing Gas Piping to Stove Location (Cont.)
Connecting Stove/Burner System to Gas Supply
Checking Gas Connections

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
15
15
Pressure Testing Burner System Gas
Connections
1. Open equipment shutoff valve (see Figure 30, page 14).
2. Open propane/LP supply tank valve for propane/LP burner
system or main gas valve located on or near gas meter for
natural gas burner system.
3. Make sure control knob of burner system is in the OFF position.
4. Check all joints from equipment shutoff valve to thermostat gas
valve (see Figure 31 for propane/LP or Figure 32 for natural,
page 15). Apply commercial leak test solution to all gas joints.
Bubbles forming show a leak. Correct all leaks at once.
5. Light burnersystem(seeLightingInstructions, page 19). Check
all other internal joints for leaks.
6. Turn off burner system (see To Turn Off Gas to Appliance,
page 19).
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
Propane/LP
Supply Tank
Equipment
Shutoff
Valve
Gas Valve
Figure 30 - Checking Gas Joints for Propane/LP Gas Burner
System (Amity™Model Shown)
Equipment
Shutoff Valve
Gas Valve
Gas Meter
Figure32 -CheckingGasJointsforNaturalGas BurnerSystem
(Amity™Model Shown)
INSTALLING OPTIONAL WALL MOUNT
SWITCH - GWMS2
1. Connect one terminal of 25 ft. wire for the wall switch to the
TPTH terminal on the valve. Connect remaining wire terminal
to the TH terminal on the valve. Make sure that the wire termi-
nals are in the positions on the unit as pictured in Figure 33. If
wires are not connected as shown, the switch will not work.
2. Route the 25 ft. wire through openings provided on the sides of
theburnersystem to aconvenientlocationto mount yourswitch.
3. Connect one bare wire end to each of the terminals of the
GWMS2 wall switch.
4. Install the wall switch and cover in the wall.
Figure 33 - Control Valve Terminals
To Control Switch or
Optional Accessory
INSTALLING OPTIONAL WALL MOUNTED
THERMOSTAT - GWMT1
WARNING:Installationmustbedonebyaqualified
installer familiar with low voltage wiring procedures.
WARNING:Donotconnectthisthermostattoany
electricalsource!Electrical shock and/orfirehazard
will occur.
1. Open lower door panel. The valve is attached to the underside
of the burner system assembly.
2. Disconnect from the valve the wires running from the ON/
OFF switch.
3. Connect one terminal of the wire for the wall thermostat to the
THTP terminal on the valve. Connect remaining wire terminal
to the TH terminal on the valve. Make sure that the wire termi-
nals are in the positions on the unit as pictured in Figure 33. If
wires are not connected as shown the thermostat will not work.
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Checking Gas Connections (Cont.)
Installing Optional Wall Mount Switch - GWMS2
Installing Optional Wall Mounted Thermostat - GWMT1

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
16
INSTALLING OPTIONAL WIRELESS HAND-
HELD REMOTE CONTROL ACCESSORIES -
GHRCB AND GHRCTB SERIES
Installing Remote Receiver
1. Open bottom door on stove body.
2. Disconnect wires from THTP and TH on control valve that
lead to the switch (see Figure 33, page 15). Discard switch
plate, screws, and nuts.
3. Install battery into receiver battery clip and connect to terminals
(see Figure 36).
4. Place receiver into valve bracket and align holes (see Figure 37).
5. Use push-in fasteners included with receiver to secure to
bracket.
6. Connect the wires from the receiver to the valve at TH and
THTP (see Figure 33, page 15).
Figure 36 - Installing Battery in Receiver
9-Volt
Battery
Receiver
Battery Clip
Terminal
Wires
Figure 37 - Installing Remote Receiver
WARNING: Do not connect this thermostat to a
powersource.Electricalshockand/orfirehazardwill
occur.
4. Route the wire to a convenient location to mount your thermo-
stat (no outside wall). IMPORTANT: The wire must not ex-
ceed 25 feet in length.
The thermostat should be mounted 54" above the floor in a
location where there is good air circulation.Avoid heat sources
such as lamps, direct sunlight, fireplace, or heat and air con-
ditioning ducts.
5. Gently remove the coverofthethermostatfromthebase.Grasp
the sides of the cover firmly and pull to separate from the base.
6. Feed the electrical wires through the rectangular slots (from
the back) on each side of the base (see Figure 34).
7. Connect one bare wire end to each terminal (“W” and “R”) of
the thermostat base (see Figure 35).
8. Install the base to the wall with screws provided with thermostat.
9. Move the temperature adjustment back and forth to insure the
bi-metal is free from restrictions.
Figure 34 - Back View of
Thermostat Base
Feed wires through
rectangular slots
Figure 35 - Thermostat
BaseTerminal“W”and“R”
W
R
Terminal
“W”
Terminal
“R”
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Installing Optional Wall Mounted Thermostat - GWMT1 (Cont.)
Installing Optional Wireless Hand-Held Remote Control Accessories - GHRCB and GHRCTB Series

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
17
17
Figure 38 - Installing Battery in Hand-Held Remote Control Unit
(GHRCB Only)
Installing 9-Volt Battery in Hand-Held Remote
Control Unit
1. Remove battery cover on back of remote control unit
2. Attach terminal wires to a 9-volt battery (not included). Place
battery into the battery housing.
3. Replace battery cover onto remote control unit.
Terminal Wires
Battery Cover
9-Volt
Battery
Remote
Control
Unit
Battery Housing
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
Figure 39 - Installing Battery in Hand-Held Remote Control Unit
(GHRCTB Only)
Terminal Wires
Battery Cover
9-Volt
Battery
Remote
Control Unit
Battery
Housing
CAUTION:Donotoperatethisburnersystemwith
a broken glass door panel or without the glass door
panel securely in place. For replacement part infor-
mation see Replacement Parts , page 26.
1. If stove front panel is still installed, remove 2 bolts from bot-
tomofstoveandone from the top of stovetoremovefrontpanel
(see Figure 40).
2. Remove the screws from the 2 tabs at the top of the glass door
while holding door securely keeping it from falling forward
(see Figure 41).
REMOVING/REPLACING GLASS DOOR
You must remove glass door to install logs, lava rock, and ember
material. To remove glass door, you must first remove the front
panel on stove body.
Figure 41 - Removing Glass Door from Burner System
Figure 40 - Removing Front Panel from Stove (Amity™Model
Shown)
Screw
Glass Door
Bolt
Bolt
Stove Front
Panel
3. Grasp door by both sides and ease it upward off of the lower
bracket (see Figure 41).
4. To replace glass door, follow the above instructions in reverse.
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Installing Optional Wireless Hand-Held Remote Control Accessories - GHRCB and GHRCTB Series (Cont.)
Removing/Replacing Glass Door

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
18
CAST IRON STOVE AND
B-VENT BURNER SYSTEM
INSTALLATION
Continued
It is very important to install these logs exactly as instructed in
Figures 42 through 46 . Do not modify logs. Only use logs supplied
withfreestandingburnersystem.Donotuseifanylog(s)arebroken
(see Replacement Parts, page 26).
1. Remove glass door. See Removing/Replacing Glass Door,
page 17.
2. Place log #1 (back log) on top of grate. Make sure the notches
in the bottom of the log fit over the grate (see Figure 42).
3. Rest log #2 (large front log) on the pins on the front part of the
grate (see Figure 43).
4. Place log #3 (crossover log) onto the rear and front logs. Make
sure it is seated properly into the notch on the front log and
over the raised triangular portion of the rear log as shown in
Figure 44.
5. Place log #4 (small log) onto thefrontleftpart ofthe gratemaking
sure the notches fits over the prong of the grate. See Figure 45.
6. Lava rock may be placed along sides and front inside burner
system bottom. This may not be visible when you have re-
placed the front of the stove. It is not necessary to use all of
the lava rock provided.
WARNING: Failure to position the parts in accor-
dance with these diagrams or failure to use only parts
specificallyapprovedwiththisburnersystemmayresult
in property damage or personal injury.
INSTALLING LOGS, LAVA ROCK, AND
GLOWING EMBERS
Figure 42-InstallingLogNo.1 Figure 43 - Installing Log
No. 2
Figure 44 - Installing Log No. 3 Figure 45 - Installing Log
No. 4
WARNING: The glass door must be securely in
place before running this burner system. Do not run
this burner system if glass is missing or broken.
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner could cause
performance problems.
7. Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the ex-
posed section of the front burner and along the space between
the burner and grate prongs (see Figure 46). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember ma-
terial in one area. It is not necessary to use all of the ember
material provided.
8. Replace the glass door and stove front. See Removing/Re-
placing Glass Door, page 17.
Figure 46 - Placing Ember Material on Burner
1
2
3
4
CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION
Installing Logs, Lava Rock, and Glowing Embers

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
19
19
TO TURN OFF GAS
TO APPLIANCE
1. Set ON/OFF switch located on rear cover to “OFF”.
2a. Open lower panel.
2b. If Using Optional Hand-Held Remote: Setselector switch in
the OFF position to prevent draining battery.
3. Turn off all electrical power to the appliance if service is to
be performed.
4. Pushingascontrol knob slightly and turnclockwise
to “OFF”.
5. Close lower panel.
Shutting Off Burners Only (pilot stays lit)
Youmayshutofftheburners andkeepthepilotlitbydoing one
of the following:
1. Turn control knob clockwise to the PILOT position.
2. Set selector switch in the OFF position.
OPERATING STOVE WITH
B-VENT BURNER SYSTEM
WARNING:Ifyou donotfollowtheseinstructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IFYOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools.Iftheknobwill not push in orturnby hand,
don'ttryto repairit,callaqualifiedservicetechnician.Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set ON/OFF switch located on rear cover to “OFF”.
3. Open lower panel.
4. Turn off all electric power to the burner system.
5. Pushingascontrol knob slightlyandturn clockwise
to “OFF”.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.
7. The pilot is located by the main burner and should not re-
quire accessing for lighting.
8. Turn knob on gas control counterclockwise to
“PILOT”.
9. Push in control knob all the way and hold. Immediately light
the pilot by repeatedly depressing the piezo spark ignitor un-
tilaflameappears. Continue to hold foraboutone(1)minute
after the pilot is lit. Release knob and it will pop back. Pilot
should remain lit. If it goes out, repeat steps 5 through 8.
Figure 47 - Control Valve
Gas Control Knob
Piezo Ignitor
• If knob does not pop up when released, stop and im-
mediately call your service technician or gas supplier.
• If the pilot willnot stay lit after several tries, turn thegas
control knob to “OFF” and call your service technician
or gas supplier.
10. Turn gas control counterclockwise to “ON”.
11. Turn on all electric power to the burner system.
12. Turn the ON/OFF switch to ON position.
13. Close lower panel.
OPERATING STOVE WITH B-VENT BURNER SYSTEM
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Manual Lighting Procedure
MANUAL LIGHTING
PROCEDURE
1. Remove glass door (see Removing/Replacing Glass Door,
page 17).
2. Follow steps 1 through 8 under Lighting Instructions.
3. Depress control knob and light pilot with match.
4. Keep control knob pressed in for 30 seconds after lighting
pilot.After30seconds,releasecontrolknob. Nowfollowsteps
10 through 13.
5. Replace glass door (see Removing/Replacing Glass Door,
page 17).

112127-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
20
OPTIONAL REMOTE
OPERATION
OPERATING STOVE WITH
B-VENT BURNER SYSTEM
Continued
Figure 48 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
Selector Switch
in Remote
Position
(Optional
Remote Control) Control Knob in On Position
OPERATING STOVE WITH B-VENT BURNER SYSTEM
Optional Remote Operation
1. After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position.Adjust flame adjustment
knobanywherebetweenHI andLO.Slidetheselectorswitch
to the REMOTE position (see Figure 48). Note: The burner
may light if hand-held remote was on when selector switch
was last turned off.You can now turn the burner on and off
with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the RE-
MOTE or ON position when the pilot is not lit. This will
drain the battery.
ON/OFF SERIES
(MODELS GHRCB AND CGHRCB)
Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 49).
TO LOCK pressbothbuttonsonhand-heldremotecontroluntil
light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.
TO UNLOCK press both buttons together on hand-held remote
control until the light stops flashing. The hand-held remote is
now unlocked.
Figure 50 - Thermostat Hand-Held Remote Control Unit
Selections (C)GHRCTB
Figure 49 - On/Off Hand-Held Remote Control Unit (C)GHRCB
Control Button
Turns Burners
On and Off
Turns Remote On
or Off and Allows
You to Choose the
Manual Setting
Selects Auto
Setting
Increases Room
Temperature in
AUTO Mode
Locks System to
Prevent Accidental
Ignition
Digital Display
Shows
Temperature and
Settings
Turns Burners
On or Off
Decreases Room
Temperature in
AUTO Mode
THERMOSTAT SERIES
(MODELS GHRCTB AND CGHRCTB)
Thehand-heldremotecanbeoperatedusingeitherthemanualmode
(MANU) or thermostatic mode (AUTO) (see Figure 50). To select
Fahrenheit/Centigrademodedisplay,carefullypressthe˚C/˚Fmode
button with the end of a paper clip or similar blunt object.
Manual Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. Press the MANU button to turn on the fireplace.
3. Press the POWER and LOCK buttons together to turn off
the fireplace.
Auto (Thermostatic) Mode
1. Press the POWER and LOCK buttons together to turn on
the hand-held remote control.
2. PressAUTO button to select this mode.
3. Set the desired room temperature by pressing the TEMP
+ or - buttons.
4. Press the POWER and LOCK buttons together to turn off
the fireplace
Note: Do not leave the hand-held remote in the AUTO mode
close to the fireplace. The radiant heat from the fireplace will
turnoffthefireplace.Ideally,placethehand-heldremoteinthe
center of the room facing towards the fireplace.
Note: Do not hold the hand-held remote for a long time. Body
temperature will affect its operation in the AUTO mode.
Safety Features
When away from home for an extended period of time or as a
child safety feature to prevent accidental ignition of the fire-
place, the receiver ON/OFF/REMOTE switch should be in the
OFF position.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instruc-
tions, page 19.
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 32). Follow instructions included
with the remote control.