Designer Pet Products NT17 SC1696 CZ User manual

1x1
5x1
9x1 10 x4
6x1 7x2
4x1 2x1 3x1
8x1
1
2
3
4
5
6
7
7
8
9
10
10
10
(3x12mm) (5x10mm)
(3.5x12mm)
(+2 extra)
(+2 extra) (+1 extra) (+1 extra)
(+2 extra) (+2 extra) (+2 extra) (+2 extra) (+2 extra) (+1 extra)(+1 extra)
Ax8 Bx8
Mx2 Nx4 Ox4 Px1
Cx18 Dx16 Ex6 Fx2 Gx2 Hx8 Ix2 Jx8 Lx4

Step 1
Step 2
Step 3
Instructions for Setup
C x 4 D x 2
C x 6 D x 6
Connect the top edging pieces
by using C pegs and D screws.
Attach the top edging pieces to the top
piece. Note that the top piece and the
bottom piece look similar. The bottom
piece has holes close to the edge on EACH
side of the bottom. The top piece only has
holes on THREE of the four sides. Use C
pegs and D screws.
Install A post screws into the
back and front pieces.
D
D
7
7
8
C
C
C
C
C
CC
C
C
C
D
D
D
DD
D
5
7
A
A
A
A
4
6
A
A
A
A
A x 8

Step 4
Step 5
Step 6
B x 4
B x 4
C x 8
Slide the front panel onto the side panels
over the posts.Insert locking screw B by
turning clockwise.
'
Now insert C pegs into the bottom of the
front, back, and side pieces.
B
B
1
3
6B
B
3
6
1
B
B
B
B
1
3
4
6
C
C
C
C
C
C
C
C
3
1
4
6
Instructions for Setup
Choose which side you would like
the entrance hole to be on. Attach
side panels using locking screw B.
Ensure that the locking screw’s
hooks are open to ensure that it
will lock around the post.
After the screw is pushed into the
hole, twist it clockwise and the
locking hooks will lock around the
posts. Do not over tighten!
Entrance Hole on the Left Entrance Hole on the Right
Option 1 Option 2
B
B
B
B

Find the F hinges and
locate the side of the
hinge that is shaped
like a right angle. Place
the hinge with the right
angle into the grooves
in the back piece of the
box.Use a screwdriver to
hold the O screws in place,
then use Allen wrench P
to screw in the N screws.
If possible, have someone
hold the top piece in place
as you install the E screws
into the F hinges on the
top piece.
Step 7
Step 8
Step 9
D x 8
L x 4
E x 6 N x 4F x 2
Install the bottom piece to the box using
the D screws. Note: the two front corners
have rounded edges,the back do not.
Install the feet by screwing them into the
bottom piece. Attach L furniture pads to
the bottom of each foot.
D
D
D
D
D
D
D
1
3
4
9
L
9
10
L
10
L
10
L
10
E
E
F
F
1
4
5
Instructions for Setup
O x 4
E
O
NF
N
P
O

Step 10
Step 11
G x 2 H x 8
1
5
Instructions for Setup
M x 2
M
M
G
H
H
H
H
G
H
H
H
H
3
4
1
5
3
4
6
M
M
I
I

J
J
J
J
catbox.
Step 12
Step 13
J x 8
J
J
J
J
J
Angle the interior panel to
place it inside the catbox
and position it in between
the holes for the pegs.
Insert the J pegs into the
8 spots on the inside of
the box.