Det-Tronics Eagle Quantum Premier EQ3900K Series User manual

1. 2 95-8769
Instructions
Eagle Quantum Premier
General Purpose Electronic Based
Equipment Enclosure Solutions
EQ3900K Series
Rev: 5/17

TABLE OF CONTENTS
DESCRIPTION ............................................1
FEATURES ...............................................1
ENCLOSURE .............................................1
SPECIFICATIONS ..........................................2
INSTALLATION ............................................2
Mounting ..............................................2
Enclosure Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Wiring Instructions ......................................2
SYSTEM COMPONENTS ....................................3
EQP System Components ................................3
Operators .............................................3
Activation Relays .......................................3
ORDERING INFORMATION ..................................7

DESCRIPTION
As part of providing the total solution to commercial
and industrial clients from around the world, Detector
Electronics Corporation offers several configurable
enclosures.
The enclosures described in this document, along with
the installed equipment, are EAC Approved (EurAsian
Conformity) for use in general purpose area (non-
hazardous) locations. Devices such as the Eagle
Quantum Premier®controller, 8 channel modules, and
power supply monitor are intended to be installed in
general purpose (non-hazardous) areas such as
control rooms. These devices must be installed in
protective enclosures.
FEATURES
• General purpose area (non-hazardous) location
installation
• Optional redundant controllers
• Louver and ventilator kits available
• Simple wire installation into terminal blocks
• Factory configurable device selection for the
enclosure
• Choice of operators and relays
• Electronics and wiring tested at the factory.
ENCLOSURE
Depending upon the equipment selection, the front
door may be supplied with a window, as well as
various indicators and operators.
If a controller is installed on the front door a locking
window kit must be installed. The window kit allows an
operator to view the controller's display, LED status
indicators and access controller's push buttons.
1.2 ©2020 Detector Electronics Corporation Rev: 5/17 95-8769
INSTRUCTIONS
Eagle Quantum Premier®
General Purpose Electronic Based
Equipment Enclosure Solutions
EQ3900K Series

1. 2 95-87692
SPECIFICATIONS
INPUT VOLTAGE—
For use with external DC power source:
24 Vdc nominal, 18 to 30 Vdc, 150 amps max.
OR
For use with external AC power source:
100...240 VAC, 45...65 Hz, 10 amps max.
POWER CONSUMPTION—
Refer to the Eagle Quantum Premier manual (number
95-8533), Section 3, Tables 3-1 and 3-2 for system
power requirements.
TEMPERATURE RANGE—
Operating: +32°F to +122°F (0°C to +50°C).
Storage: –4°F to +158°F (–20°C to +70°C).
HUMIDITY—
5% to 80% RH, non-condensing.
RELAY ELECTRICAL CHARACTERISTICS—
Input voltage (coil), nominal, all relay types – 24 Vdc.
Contact ratings – refer to manufacturer specification.
CERTIFICATION—
EurAsian Conformity
Compliance with: KZ.1510019.22.01.00187
WEIGHT (Without Electronic Assemblies)*—
Floor Mount with Back Panel
2000 x 600 x 600: 124.4 kg (333. lbs).
2000 x 800 x 600: 153.4 kg (411 lbs).
2000 x 800 x 800: 63.56 kg (438 lbs).
2000 x 1000 x 600: 82.94 kg (490 lbs).
2000 x 1000 x 800: 184 kg (492 lbs).
2000 x 2000 x 600: 365.92 kg (980.5 lbs).
2000 x 2000 x 800: 368 kg (986 lbs).
Wall Mount with Back Panel
300 x 300 x 210: 7 kg (15.4 lbs).
500 x 500 x 210: 16.8 kg (37 lbs).
600 x 600 x 250: 24.8 kg (54.7 lbs).
800 x 600 x 250: 33.6 kg (74.1 lbs).
1000 x 600 x 250: 50.5 kg (111.3 lbs).
1000 x 800 x 300: 57 kg (125.7 lbs).
1200 x 600 x 300: 55 kg (121.3 lbs).
* Total weight dependent on cabinet depth and equipment
loading. See EQP Enclosures Model Matrix.
INSTALLATION
The enclosure must be securely bolted in place.
MOUNTING
Refer to the appropriate system drawing for mounting
dimensions.
ENCLOSURE ENTRY
The number and position of wiring entries must be
specified when the enclosure is ordered. The
enclosures can accept a certain number and size of
entries as specified by enclosure manufacture. Only
manufacturer recommended cable glands can be
used with the enclosures. Consult with Det-Tronics on
the exact number and sizes of entries that are available
for each enclosure.
WIRING INSTRUCTIONS
Factory wiring is made to the appropriate terminals
located inside the enclosure. Electrical wiring
schematics for the custom device configuration are
provided with the enclosure. Field wiring and field
wiring tags are the responsibility of the customer.

1. 2 95-87693
SYSTEM COMPONENTS
EQP SYSTEM COMPONENTS
The following devices can be used in EQ3900K
enclosures as part of the EAC Approved Eagle
Quantum Premier System:
EQ3XXX - EQP Controller
EQ3700DCIO - Discrete Input/Output Module
EQ3710AIM - Analog Input Module
EQ3720RM - Relay Module
EQ3730EDIO - Enhanced Discrete Input/Output Module
EQ3LTM - LON Termination Module
EQ2100PSM - Power Supply Monitor
EQ2220GFM - Ground Fault Monitor
EQ3750ASH - Addressable Smoke and Heat Module
EQ24EMNE - Network Extender, Panel Mount
Phoenix RS-232/RS-485 - Ethernet Converters
Refer to the Eagle Quantum Premier manual (number
95-8533) for operation details.
The quantity and type of modules are always project
specific per Sales Order and drawing packet supplied
with the order. The I/O allocation may be moved from
factory assigned terminals after notification to Det-
Tronics.
NOTES
1. New inputs/outputs may be wired onto spare
channels after factory notication.
2. One-for-one replacement of failed modules is
permitted.
3. Modications and/or repairs should be performed
by trained personnel only.
OPERATORS
Enclosures may be equipped with selector switches,
pilot lights and push buttons, and panel horns. Contact
Det-Tronics for information regarding model and type
of operators approved for use with EQ3900K series
enclosures. The quantity, type of operators and their
application are always project specific per Sales
Order and drawing packet supplied with the order.
Approved push button quantities for use in
Acknowledge and Silence applications vary depending
on manufacturer. The I/O allocation may be moved
from factory assigned terminals after notification to
Det-Tronics. See Notes 4 and 5 in Figures 1 thru 3 for
configuration change details.
NOTE
Per NFPA 72 requirements, Acknowledge and
silence pushbuttons must be used with
padlocking covers with locks as guards against
unauthorized operations. Padlocking covers are
offered by Det-Tronics and factory installed as
guards with Acknowledge and Silence push
buttons. Locks are not included.
ACTIVATION RELAYS
Five activation relays (two Tyco and three Phoenix
Contact relays) are available for use with the EQP
system. Activation relays are intended for occasional
use. They are typically used for HVAC control where
they become actuated primarily when the protected
area is in an alarm condition. For relay wiring
connections, see Figure 1 for Tyco relays and Figures
2 and 3 for Phoenix Contact relays. Tyco relays can be
installed inside the EQ3900K enclosure, or inside the
customer's provided enclosure at site, while still
connected to I/O modules within the EQ3900K
enclosure. When Tyco relays are located in the
customer's enclosure, installation, wiring and operation
of Tyco relays must meet all requirements of the local
Authority Having Jurisdiction (AHJ). Phoenix Contact
relays are installed only within EQ3900K enclosures.
For additional information regarding relays, see Tyco
product catalog 1308242 or Phoenix Contact product
data sheets 101780-en-02 and 100516-03-en.

1. 2 95-87694
Figure 1—Typical Supervised Output Conguration Using Tyco Relays
EOL RESISTOR
10K OHM, 1/2 WATT
R1
D1
AB
R2
D2
A B
C B
24 VDC
TEST SWITCH
CONTACT
OPENS
DURING TEST
I/O MODULE OUTPUT
1-3/C#14 OR 2#14 IN
CONDUIT
R1-1
4 6
R2-1
4
1
7
+
R2-2
6
3
9
+
TEST
SWITCH
CONTACT
SWITCH
OPENS IN TEST
POSITION
TEST SW
EQP PANEL
INPUT
R1 - TYCO KUEP-3D15-24 R2 - TYCO KUP-11D15-24
(DEC P/N 000123-198) (DEC P/N 000123-199)
TYCO RELAYS IN HVAC APPLICATIONS
NOTES: 1. D1 & D2 ARE SUPERVISORY DIODES:
D1 - IN4004 (RECTIFIER, 1A, 400V) OR D2 - GI501 (RECTIFIER, 3A, 50V).
2. OPTIONAL TEST SWITCH IN ENCLOSURE ALLOWS TESTING OF TRIP CIRCUIT.
3. TEST SWITCH WILL BLOCK ACTIVATION OF TRIP CIRCUIT DURING SENSOR TESTING.
4. THE I/O ALLOCATION MAY BE MOVED FROM FACTORY ASSIGNED TERMINALS AFTER
FACTORY NOTIFICATION. ALL CHANGES MUST BE DOCUMENTED.
5. MODIFICATIONS AND/OR REPAIRS SHOULD BE PERFORMED BY TRAINED PERSONNEL ONLY.
6. WHEN TYCO RELAYS ARE INSTALLED IN REMOTE ENCLOSURE, THE MAXIMUM WIRING LENGTH
BETWEEN I/O MODULE AND RELAYS IS 3000 FEET (914 METERS) USING 14 AWG WIRE.
7. TYCO RELAYS MAY BE INSTALLED IN THE SAME ENCLOSURE WITH I/O MODULE.
INTERNAL WIRING IS 16 AWG, RATED 600 VOLTS TYPICAL.
8. THE SYSTEMS SUPERVISION CONFIGURATION MUST BE SET FOR MONITORED FOR OPENS/SHORTS.
REMOTE EQ3900K ENCLOSURE
OR
ENCLOSURE SUPPLIED
BY OTHERS
EQ3900K ENCLOSURE

1. 2 95-87695
Figure 2—Typical Supervised Output Conguration Using a Phoenix Contact Relay Model 2966171
EOL RESISTOR
10K OHM, 1/2 WATT
(see note 7)
R1
AB
C B
24 VDC
TEST SWITCH
CONTACT
OPENS
DURING TEST
I/O MODULE OUTPUT
ALL WIRING IS
16 AWG, 600V RATED, TYPICAL
+
11
TEST
SWITCH
CONTACT
SWITCH
OPENS IN TEST
POSITION
TEST SW
EQP PANEL
INPUT
PHOENIX CONTACT RELAY MODEL 2966171 IN HVAC APPLICATIONS
12
14
R1
NOTES: 1. PHOENIX RELAY 2966171 (DEC P/N 000123-196) IS EQUIPPED WITH INTERNAL SUPERVISORY DIODE.
2. OPTIONAL TEST SWITCH IN ENCLOSURE ALLOWS TESTING OF TRIP CIRCUIT.
3. TEST SWITCH WILL BLOCK ACTIVATION OF TRIP CIRCUIT DURING SENSOR TESTING.
4. THE I/O ALLOCATION MAY BE MOVED FROM FACTORY ASSIGNED TERMINALS AFTER
FACTORY NOTIFICATION. ALL CHANGES MUST BE DOCUMENTED.
5. MODIFICATIONS AND/OR REPAIRS SHOULD BE PERFORMED BY TRAINED PERSONNEL ONLY.
6. THE SYSTEMS SUPERVISION CONFIGURATION MUST BE SET FOR MONITORED FOR OPENS/SHORTS
7. SUPERVISION IS OPTIONAL WHEN RELAY IS MOUNTED IN THE SAME ENCLOSURE AS OUTPUT DRIVER.
EQ3900K
ENCLOSURE

1. 2 95-87696
Figure 3—Typical Supervised Output Conguration Using a Phoenix Contact Relay Model 2981020 or 2963912-PSR-SCP-24UC
EOL RESISTOR
10K OHM, 1/2 WATT
(see note 7)
R1
AB
C B
24 VDC
TEST SWITCH
CONTACT
OPENS
DURING TEST
I/O MODULE OUTPUT
ALL WIRING IS
16 AWG, 600V RATED, TYPICAL
TEST
SWITCH
CONTACT
SWITCH
OPENS IN TEST
POSITION
TEST SW
EQP PANEL
INPUT
PHOENIX CONTACT RELAY MODEL 2981020 OR 2963912 PSR-SCP-24UC IN HVAC APPLICATIONS
13 23 31
14 24 32
R1
NOTES: 1. PHOENIX RELAY 2981020 SIL3 (DEC P/N 000123-197) IS EQUIPPED WITH INTERNAL SUPERVISORY DIODE (SHOWN).
OR PHOENIX RELAY 2963912 PSR-SCP-24UC (DEC PN 000123-229) IS EQUIPPED WITH INTERNAL SUPERVISORY DIODE.
2. OPTIONAL TEST SWITCH IN ENCLOSURE ALLOWS TESTING OF TRIP CIRCUIT.
3. TEST SWITCH WILL BLOCK ACTIVATION OF TRIP CIRCUIT DURING SENSOR TESTING.
4. THE I/O ALLOCATION MAY BE MOVED FROM FACTORY ASSIGNED TERMINALS AFTER
FACTORY NOTIFICATION. ALL CHANGES MUST BE DOCUMENTED.
5. MODIFICATIONS AND/OR REPAIRS SHOULD BE PERFORMED BY TRAINED PERSONNEL ONLY.
6. THE SYSTEMS SUPERVISION CONFIGURATION MUST BE SET FOR MONITORED FOR OPENS/SHORTS.
7. SUPERVISION IS OPTIONAL WHEN RELAY IS MOUNTED IN THE SAME ENCLOSURE AS OUTPUT DRIVER.
EQ3900K
ENCLOSURE

1. 2 95-87697
EQ3900K Model Matrix
MODEL DESCRIPTION
EQ3900K EAC Approved Assemblies for EQP: General Purpose (Non-Hazardous) Area Locations
TYPE EQP CONTROLLER
0Quantity 0
1Quantity 1
2Quantity 2 (Redundant Conguration)
TYPE ENCLOSURE HEIGHT and WIDTH
SIZE H W D NOTES
FLOOR MOUNT IP55
A 2000 600 600
B 2000 800 600
C 2000 800 800
D 2000 1000 600
E 2000 1000 800
F 2000 2000 600 2 Cabinets Joined
G 2000 2000 800 2 Cabinets Joined
WALL MOUNT IP55
H 300 300 210 Remote I/O Only
I 500 500 210 Remote I/O Only
J 600 600 250 Remote I/O Only
K 800 600 250 Remote I/O Only
L 1000 600 250
M 1000 800 300
N 1200 600 300
TYPE WINDOW CONFIGURATION
ANo Window
B Operable Window (With Key Lock)
CFixed Window
TYPE DESCRIPTION
XXXXXXXX-XXX Sales Order # Drawing Packet
EQ3900K Design Criteria
FLOOR MOUNTED ENCLOSURES
SIZE MAXIMUM NUMBER OF
EQP I/O MODULES
A12
B16
C16
D16
E16
F 32
G 32
WALL MOUNTED ENCLOSURES
SIZE MAXIMUM NUMBER OF
EQP I/O MODULES
H 1
I 2
J 3
K 4
L 5
M 7
N 8
ORDERING INFORMATION
Refer to the EQ3900K Enclosures Model Matrix for details.
For assistance in ordering a system to fit your application,
please contact:
Detector Electronics Corporation
6901 West 110th Street
Minneapolis, Minnesota 55438 USA
Operator: [phone] or (800) 765-FIRE
Customer Service: [phone]
Fax: [phone]
E-mail: [e-mail]

X3301 Multispectrum
IR Flame Detector
FlexSonic®Acoustic
Leak Detector
PointWatch Eclipse®IR
Combustible Gas Detector
FlexVu®Universal Display
with GT3000 Toxic Gas Detector
Eagle Quantum Premier®
Safety System
95-8769
Corporate Office
6901 West 110th Street
Minneapolis, MN 55438 USA
www.det-tronics.com
Phone: [phone]
Toll-free: +1 800.765.3473
Fax: [phone]
[e-mail]
Specications subject to change without notice.
All trademarks are the property of their respective owners.
© 2020 Detector Electronics Corporation. All rights reserved.
Det-Tronics manufacturing system is certied to ISO 9001—
the world’s most recognized quality management standard.