DEVAISE ADYJ002 User manual

ADYJ002
Wood Printer Organizer with Shelf V3.1

GENERAL GUIDELINES
WARNINGS
Please read the following instruction carefully and use the product accordingly.
During assembly, keep parts and packaging materials away from children and pets as there
could cause injury and are a potential choking hazard.
Avoid sharp objects or corrosive chemicals to prevent damage to the product.
Please open the item slowly and cautiously to avoid pinching your hands by metal joints,
especially children.
If an odor is present when first opening the package, please leave the unwrapped product in
a shaded and ventilated area for a few days to air out.
Please follow the assembly instructions precisely and only use the product as intended.
Prior to assembly, please check the product for defects or missing accessories. If any
defects are found or accessories are missing, do not use product as damage or injury
may occur;
Please contact us for assistance and replacement.
It is suggested you regularly check the products bolts and connections to ensure safe use.
Assemble the item on a soft flat and clean surface to avoid scratches and damage.
It is recommended that two people assemble this product.
Please keep this manual and hand it over when you transfer the product.
This summary may not include every detail of all variations and considered steps.
Please contact us when further information and help are needed.
•
•
•
•
•
•
•
•
•
•
•
•
IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.
NOTES

If you have any further questions, please feel free to contact us
by email or official website: [email protected]
We will reply ASAP.
Enjoy your new purchase!
Before installation, please make sure you have all the hardware,
the serial numbers are properly labeled corresponging to the list,
and the quantity is correct.

1
EXPLODED DRAWING
PARTS
X16 X16
B
X16
C
A
X24
X2
F
D
X8
H
X2
E
X12
G
M4x11
M4x14
X2
J
X4
I
X8
KX1 L
L1 L2
1
2
10
5
7
8
4
6
3
9

2
1
MINIFIX POSITION
REMARK
X2
A
X4
B
REMARK
1. Please do not screw too deep or too shallow.
A
2. Put a blanket under the board to avoid scratch or damage.
DEV
V
ISE
214/
×2
A
4
×4
B

3
2
3
X4
B
REMARK
The innerside should be the edge banding side.
The position indicated by the finger on the side
without eccentric hole is correct .
5
5
5
4
B4
REMARK

4
X4
A
X8
B
4
5
X2
C
1
2
5
4
×2
C
A4
B8

5
REMARK
6X4
C
REMARK
C4
Please make sure the up side slot of
part 1and 2is on the same side.
1
1
2
2
5
4
4
4
The down should be the edge banding side.
UP
UP
DOWN
DOWN

6
REMARK
7
8
X10
A
X4
C
C4
Let the grooves on part 1 and 2be connected
to the groove on part 3.
3
3
3
10
2
2
A10
1
1

7
9
10 X6
C
C6
10
1
2
2
7
7
7
2
10

8
11
12 X8H
M4x14
KDM4x11
X2
E
X2
F
X16
D
M4x11
×16
D
E
F
E
F
×8
H

9
13
14
2. Part 6and 8is adjustable shelf .
1. The long shadow part is in front
and the short one is inside.
REMARK
short
long
L1
L1
L1
L2
L2
M4x14
KDM4x11
9
X4K
M4x14
X1L
X2J
J
H
H
JK4
3. Please make the groove on part 6 and 8match with the part .
8
8
6
6

10
M4x14
KDM4x11
15
16
X8D
M4x11
X12
G
×12
G
D8
9

11
17
×4
+K
I
X4
X4
I
K
M4x14

12
HINGE ADJUSTMENT
If the door do not appear square or aligned,loosen or tighten the appropriate screws on each case
hinge as illustrated.
Loosen screw ( Do not loose screw to the end), push hinge arm forwards or backwards,
re-tighten screw .
BB
1 2
DEPTH ADJUSTMENT
B
B
C
B
Adjust screw to make hinge move left or right to the ideal place.
C
SIDE TO SIDE ADJUSTMENT