DeWalt Emglo D55151 User manual

If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, cont&ctenos.
iNSTRUCTiON MANUAL
GUIDE D'UTILiSATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA
DE GARANTiA. ADVERTENClA: LI_ASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
®
D55151, D55152, D55153, D55155
Contractor's Electric 4 Gallon Hand Carry Air Compressor
Compresseurs d'air portatifs 61ectriques de 4 gallons de classe entrepreneur
Compresor de aire portatil electrico de 4 galones para contratistas

Air Compressor
A. On/Off Switch
B. Air Tank Pressure Gauge
C. Regulated Pressure Gauge
D. Pressure Regulator
E. Quick Connects (if equipped)
F. Check Valve
G. Safety Valve
H. Air Tank Drain Valve
I. Power Cord Wrap
J. Pressure Switch
K. Pump Oil Dipstick
L. Pump Oil Drain Plug
M. Motor Reset
N. Air Intake Filter
FIG. 1 BNOT A
STEP DB
A
A
K
C
D
M
2

Specifications
MODEL D55155
!
D55152
65 Ibs. (29.5 kg)
16.0" (406.4 ram)
18.0" (457.2 ram)
18.0" (457.2 ram)
4.0 (15.1 liters)
95 PSI (655 kPa)
125 PSI (861.8 kPa)
3.8
1.1 HP (continuous)
120V/14 A/60 Hz.
3450
15 Amp
WEIGHT 56 Ibs. (25.4 kg) 58 Ibs. (28.3 kg) 61 Ibs. (27.7 kg)
HEIGHT 16.75" (425.5 mm) 16.75" (501.7 mm) 12.5" (317.5 mm)
WIDTH 18.0" (457.2 mm) 18.0" (457.2 mm) 21.75" (552.5 mm)
LENGTH 15.0 (381 mm) 15.0 (381 mm) 21.75" (552.5 mm)
AIRTANK CAPACITY (GALLONS) 4.0 (15.1 liters) 4.0 (15.1 liters) 4.0 (15.1 liters)
APPROX CUT=IN PRESSURE 95 PSi (655 kPa) 95 PSi (655 kPa) 100 PSi (689.5 kPa)
APPROX. CUT=OUT PRESSURE 125 PSi (861.8 kPa) 125 PSi (861.8 kPa) 125 PSi (861.8 kPa)
SCFM @ 100 PSI (689.5 kPa) 3.2 3.8 4.5
MOTOR 1.1 HP (continuous) 1.1 HP (continuous) 1.2 HP (continuous)
Volts/Amps/Hertz 120V/12.5 A/60 Hz. 120V/14 A/60 Hz. 120V/15 A/60 Hz.
RPM 3450 3450 3450
Minumum Branch Circuit 15 Amp 15 Amp 15 Amp
Requirement
PUMP OIL CAPACITY 6 oz. (177.4 ml) 12 oz. (354.9 ml) 12 oz. (354.9 ml) 4 oz. (118.3 ml)

Hot Surfaces PUMP
FIG.2 CYLNDER
AND
OUTLET TUBE CHECK /
VALVE /CHECK
OUTLET TUBE VALVE
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
`&DANGER: Indicates an imminently hazardous
situation which, ff not avoided, wifl result in death
or serious injury.
AWARNING: Indicates a potentially hazardous
situation which, ff not avoided, could result in death
or serious injury.
,&CAUTION: Indicates a potentially hazardous
situation which, ff not avoided, may result in minor
or moderate injury.
CAUTION: Used without the safety alert symbol
indicates a potentially hazardous situation which, ff
not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT
THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT:
I=800=4=DEWALT (1-800=433=9258)
Important Safety Instructions
_, WARNING: Do not operate this unit until you read and understand
this instruction manual for safety, operation and maintenance
instructions.
AWARNING: Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or other
reproductive harm. Some example of these chemicals are:
* lead from lead-based paints
* crystalline silica from bricks and cement and other masonry
products
* arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often
you do this type of work. Toreduce your exposure to these chemi-
cals: work in a weft ventilated area, and work with approved safety
equipment, always wear OSHA/MSHA/NIOSH approved, properly
fitting face mask or respirator when using such tools.
When using air tools, basic safety precautions should always be fol-
lowed to reduce the risk of of personal injury,
_WARNING: This product contains chemicals, including lead,
known to the State of California to cause cancer, and birth
defects or other reproductive harm. Wash hands after handling.
SAVE THESE INSTRUCTION

,t_DANGER: RISK OF EXPLOSION OR FIRE
WHAT CAN HAPPEN HOWTO PREVENT iT
• It is normal for electrica! _ Always operate the compres_
contacts within the motor Sorin a well ventilated area
and pressure switch to free of combustible materials,
spark, gasoline, or solvent vapors.
• If electrical sparks from • If spraying flammable materi-
compressor come into con- als, locate compressor at
tact with flammable vapors, east 20 feet 16.1m) away
they may ignite, causing fire from spray area. An addi-
or explosion, tional length of hose may be
required.
- Store flammable materials q
a secure location away from
compressor.
• Restricting any of the com- • Never place objects against
pressor ventilation openings or on top of compressor
will cause serious overheat- • Operate compressor in
ing and could cause fire. an open area at least 12"
(30.5 cm) away from any
wall or obstruction that would
restrict the flow of fresh air to
the ventilation openings.
•Operate compressor in a
clean, dry well ventilated area.
Do no_operate unit indoors or
in any confined area.
Unattended operation of
this product could result in
personal injury or property
damage. To reduce the risk
of fire, do not allow the
compressor to operate unat-
tended.
• Always remain in attendance
with the product when it is
operating.
• Always turn off and unplug
unit when not in use.
ADANGER: RISK TO BREATHING (ASPHYXIATION)
WHAT CAN HAPPEN HOWTO PREVENTIT
, The compressed air directly - Air obtained directly from the
from your compressor is not compressor should never
safe for breathing. The air be used to supply air for
stream may contain carbon human consumption. Inorder
monoxide, toxic vapors, to use air produced by this
or solid particles from the compressor for breathing
air tank. Breathing these suitable filters and in-line
contaminant's can cause safety equipment must be
serious injury or death, properly installed. In-line
filters and safety equipment
used in conjunction with the
compressor must be capable
of treating air to all applicable
local and federal codes prior to
human consumption

Sprayedmaterialssuchas
paint,paintsolvents,paint
remover,insecticides,weed
killers,maycontainharmful
vaporsandpoisons.
Workinanareawithgood
crossventilation.Readand
followthesafetyinstructions
providedonthelabelorsafety
datasheetsforthematerials
youarespraying.Alwaysuse
certifiedsafetyequipment:
OSHA!MSHA/NIOSH
respiratoryprotectiondesigned
forusewithyourspecific
application.
_&DANGER:RISK OF INJURY OR PROPERTY DAMAGE WHEN
TRANSPORTING OR STORING
WHAT CAN HAPPEN HOWTO PREVENTIT
o Oil can leak or spill and could - Always place compressor
result in fire or breathing on a protective mat when
hazard; serious injury or transporting to protect against
death can result.Oil leaks will damage to vehicle from leaks.
damage carpet, paint or other Remove compressor from
surfaces invehicles or trailers, vehicle immediately upon arrival
at your destination. Always keep
compressor leveland never lie
on its side.
_&WARNING: RISK OF BURSTING
AirTank: The air tank on your Air Compressor is designed and may
be UM coded (for units with air tanks greater than 6 inch diameter)
according to ASME Section VIII, Div. 1 rules. All pressure vessels
should be inspected once every two years.To find your state pressure
vessels inspector, look under the Division of Labor and Industries in
the government section of a phone book or call 1-800-4-DEWALT for
assistance.
The following conditions could lead to a weakening of the air tank,
and result in aviolent air tank explosion:
WHAT CAN HAPPEN HOWTO PREVENT IT
Failure to properly drain _ Drain air tank daily or after
each use. If air tank develops
a leak. replace it immediately
with a new air tank or replace
the entire compressor.
Modifications or attempted - Never drill into. weld, or make
repairs to the air tank, any modifications to the air
tank or its attachments. Never
attempt to repair a damaged or
leaking air tank. Replace with a
new air tank.
•• The airtank is designed
to withstand specific
operating pressures. Never
make adjustments or parts
substitutions to alter the factory
set operating pressures.
Unauthorized modifications
to the safety valve or any
other components which
control air tank pressure.
condensed water from
air tank. causing rust and
thinning of the steel air tank.

Attachments&accessories:
Exceeding the pressure • Follow the equipment
rating of air tools, spray guns. manufacturers
air operated accessories, recommendation and never
tires, and other inflatables exceed the maximum
can cause them to explode allowable pressure rating
or fly apart, and could result of attachments. Never use
in senous injury, compressor to inflate small
low pressure objects such
as children's toys, footballs,
basketballs, etc.
AWARNING: RiSK OF ELECTRICAL SHOCK
• Repairs attempted by
unqualified personnel can
result in serious injury or
death by electrocution.
WHAT CAN HAPPEN HOWTO PREVENT iT
" Youiair c0mpress0r is .Never operate the
powered bYelectricity, compressor outdoors when it
Like any other electrically is raining 0r in wet conditions.
powered device, !fit iS not ,, Never operate comPressor
used proper!y it may cause with protective covers
electric shock, removed or damaged.
• Any electrical wiring or
repairs required on this
product should be performed
by a DEWALT factory
service center or a DEWALT
authorized service center in
accordance with national and
local electrical codes.
-Electrical Grounding: = Make certain that the
Failure to provide adequate electrical circuit to which the
grounding to this product compressor is connected
could result in serious injury provides proper electrical
or death from electrocution, grounding, correct voltage
See Grounding and adequate fuse protection.
instructions under
Installation.
AWARNING: RISK FROM FLYING OBJECTS
WHAT CAN HAPPEN
• The compressed air stream
can cause soft tissue
damage to exposed skin and
can propel dirt, chips, loose
particles, and small objects
at high speed, resulting in
property damage or personal
injury.
HOWTO PREVENT IT
• Always wear certified safety
equipment: ANSI Z87.1 eye
protection (CAN/CSA Z94.3)
with side shields when using
the compressor.
• Never point any nozzle or
sprayer toward any part of
the body or at other people or
animals.
Always turn the compressor off
and bleed pressure from the
air hose and air tank before
attempting maintenance,
attaching tools or accessories.

AWARNING:RiSK OF HOT SURFACES
WHAT CAN HAPPEN HOWTO PREVENT JT
•Touching exposed metal -Never touch any exposed
such as the compressor metal parts on compressor
head. engine head, engine during or immediately after
exhaust or outlet tubes, can operation. Compressor will
result in serious burns, remain hot for several minutes
after operation.
• Do not reach around
protective shrouds or attempt
maintenance until unit has
been allowed to cool.
_, WARNING: RiSK FROM MOVING PARTS
WHAT CAN HAPPEN HOWTO PREVENT IT
Moving parts such as the
pulley, flywheel, and belt can
cause serious injury ifthey
come into contact with you or
your clothing.
• Never operate the compressor
with guards or covers which
are damaged or removed.
• Keep your hair,clothing, and
gloves away from moving
parts. Loose clothes, jewelry,
or long hair can be caught in
moving parts.
• Air vents may cover moving
parts and should be avoided
as well.
-Attempting to operate o Any repairs required on this
compressor with damaged or product should be performed
missing parts or attempting by a DEWALTfactory
to repair compressor with service center or a DEWALT
protective shrouds removed authorized service center.
can expose you to moving
parts and can result in
serious injury.
AWARNING: RISK OF UNSAFE OPERATION
WHAT CAN HAPPEN HOWTO PREVENT IT
Unsafe operation of your air
compressor could lead to seri-
ous injury or death to you or
others.
Review and understand all
instructions and warnings in
this manual.
• Become familiar with the
operation and controls of the
air compressor.
• Keep operating area clear of all
persons, pets, and obstacles.
• Keep children away from the
air compressor at all times.
• Do not operate the product
when fatigued or under the
influence of alcohol or drugs.
Stay alert at all times.
• Never defeat the safety fea-
tures ofthis product.

• Equipareaofoperationwitha
fireextinguisher.
• Donotoperatemachinewith
missing,broken,orunautho-
rizedparts.
WARNING: RiSK OF FALLING
WHAT CAN HAPPEN HOWTO PREVENTIT
A portable compressor _ Always operate compressor
can fall from a table, in a stable secure position to
workbench, or roof causing prevent accidental movement
damage to the compressor of the unit. Never operate
and could result in serious compressor on a roof or
njury or death to the other elevated position. Use
operator, additio nal air hose to reach
high locations.
ACAUTION: RISK FROM NOISE
WHAT CAN HAPPEN HOWTO PREVENT IT
Under some conditions and • Always wear certified safety
duration of use, noise from equipment: ANSI S12.6
this product may contribute (S3.19) hearing protection.
to hearing loss.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
FEATURES (Fig. 1)
ON/OFF SWITCH
Place this switch (A) in the ON position to
provide automatic power to the pressure
switch and OFF to remove power at the
end of each use.
PRESSURE SWITCH
The pressure switch (J) automatically
starts the motor when the air tank pres-
sure drops below the factory set cut-in
pressure. It stops the motor when the air tank pressure reaches the
factory set cut-out pressure.
PRESSURE RELEASE VALVE
The pressure release valve located on the side of the pressure switch,
is designed to automatically release compressed air from the compres-
sor head and the outlet tube when the air compressor reaches cut-out
pressure or is shut off. The pressure release valve allows the motor to
restart freely.When the motor stops running, air will be heard escaping
from this valve for a few seconds. No air should be heard leaking when
the motor is running or after the unit reaches cut-out pressure.
SAFETY VALVE
If the pressure switch does not shut off the air compressor at its
cut-out pressure setting, the safety valve (G) will protect against
high pressure by popping out at its factory set pressure (slightly
higher than the pressure switch cut-out setting).
CHECK VALVE
When the air compressor is operating, the check
valve (F) is open, allowing compressed air to enter
the air tank. When the air compressor reaches cut-
out pressure, the check valve closes, allowing air
pressure to remain inside the air tank.

TANKPRESSUREGAUGE
Thetankpressuregauge(B)indi-
catesthereserveairpressurein
thetank.
OUTLETPRESSUREGAUGE
Theoutletpressuregauge(C)
indicatestheairpressureavailable
attheoutletsideoftheregulator.
Thispressureiscontrolledbytheregulatorandisalwayslessthan
orequaltothetankpressure.
REGULATOR
Theregulator(D)controlstheairpressureshownontheoutlet
pressuregauge.Turnregulatorknobclockwisetoincreasepres-
sureandcounterclockwisetodecreasepressure.
UNIVERSALQUICKCONNECTBODIES(IFEQUIPPED)
Theuniversalquickconnectbody(E)acceptsthethreemost
popularstylesofquickconnectplugs:Industrial,automotive,and
ARO.Onehandpush-to-connectoperationmakesconnections
simpleandeasy.Thetwoquickconnectbodiesallowtheuseoftwo
toolsatthesametime.
DRAIN VALVE
The drain valve (H) is located at the base
of the air tank and is used to drain conden-
sation atthe end of each use. See Draining
Air Tank under Maintenance.
COOLING SYSTEM
This compressor contains an advanced design cooling system.
It is normal for this fan to blow air through the vent holes in large
amounts. The cooling system is working when air is expelled.
AIR COMPRESSOR PUMP
The pump compresses air into the air tank. Working air is not
available until the compressor has raised the air tank pressure
above that required at the air outlet.
MOTOR OVERLOAD PROTECTOR
This motor has a manual thermal overload
protector. If the motor overheats for any
reason, the overload protector will shut off
the motor. The motor must be allowed to
cool down before restarting. To restart:
1. Ensure the On/Off switch (A) is in the
OFF position.
2. Allow the motor to cool.
3. Depress the reset button (M) on the
motor.
OIL DIPSTICK
The oil dipstick (K) indicates the amount of oil in the pump. Check
pump oil daily, see Compressor Pump Oil under Maintenance.
AIR iNTAKE FILTER
The filter (N) is designed to clean air entering the pump. To ensure
the pump continually receives a clean, cool, and dry air supply the
filter must always be clean and the filter intake must be free from
obstructions.
INSTA£LATION
Assembly
iNSTALLING HOSES
WARNING: Risk of unsafe operation. Firmly grasp hose in hand
when installing or disconnecting to prevent hose whip.
lO

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).
2. Grasp the hose at the quick connect plug and push the plug
into the quick connect body (E). Coupler will snap into place.
3. Grasp the hose and pull to ensure coupler is seated.
DISCONNECTING HOSES
Ik WARNING: Risk of unsafe operation. Firmly grasp hose in hand
when installing or disconnecting to prevent hose whip.
1. Ensure regulated pressure gauge reads 0 PSi (0 kPa).
2. Pull coupler on quick connect body back to release quick
connect plug on hose.
Lubrication and Oil
CAUTION: The compressor was shipped with oil in the crankcase.
A shipping plug is used to prevent oil from leaking during shipment.
Do not attempt to operate this air compressor without first checking
the oil level. Serious damage can result from even limited operation
unless filled with oil and broken in correctly. Closely follow Initial
Set-up under Operation.
CAUTION: Multi-viscosity motor oils, like 10W30, should not be
used in an air compressor. They leave carbon deposits on critical
components, thus reducing performance and compressor like. Use
SAE 40, non-detergent air compressor oil only.
1. Place unit on a level surface.
2. Remove the shipping plug and install the
dipstick.
3. Remove the dipstick (K) and check the oil
level. Oil should not exceed top raised line on
dipstick. If oil is below lower mark see Checking
Oil under Compressor Pump Oil under
Maintenance. NOTE: See Specifications for _
pump oil capacity.
CAUTION: Risk of unsafe operation. Overfilling with oil will cause
premature compressor failure. Do not overfill.
4. Replace dipstick.
Grounding instructions
_&WARNING: Risk of electrical shock. In the event of a short circuit,
grounding reduces the risk of shock by providing an escape wire for
the electric current. This air compressor must be properly grounded.
The portable air compressor is equipped with a cord having a
grounding wire with an appropriate grounding plug.
1. The cord set and plug (0) with this unit
contains a grounding pin (P).This plug
MUST be used with a grounded outlet
(Q).
IMPORTANT: The outlet being used must
be installed and grounded in accordance
with all local codes and ordinances.
2. Ensure the outlet being used has the same configuration as the
grounded plug. DO NOT USE AN ADAPTER.
3. Inspect the plug and cord before each use. Do not use if there
are signs of damage.
4. If these grounding instructions are not completely understood, or
if in doubt as to whether the compressor is properly grounded,
have the installation checked by a qualified electrician.
_DANGER: Risk of electrical shock. IMPROPER GROUNDING
CAN RESULT IN ELECTRICAL SHOCK.
*Do not modify the plug provided, ff it does not fit the available
outlet, a correct outlet should be installed by a quafified electri-
cian.
*Repairs to the cord set or plug MUST be made by a quafified
electrician.
11

Extension Cords
Using extension cords is not recommended. The use of extension
cords will cause voltage to drop resulting in power loss to the motor
and overheating.
Instead of using an extension cord, increase the working reach of
the air hose by attaching another length of hose to its end. Attach
additional lengths of hose as needed.
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade grounding plug, and
a 3-slot receptacle that will accept the plug on the product
• in good condition
• no longer than 50 feet (15,2 m)
• 12 gauge (AWG) or larger. (Wire size increases as gauge num-
ber decreases. 10 AWG and 8 AWG may also be used. DO NOT
USE 14 OR 16 AWG.)
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit Requirements
under Specifications.
_,CAUTION: Certain air compressors can be operated on a
15 amp circuit if the following conditions are met.
• Voltage supply to circuit must comply with the National Electrical
Code.
• Circu# is not used to supply any other electrical needs.
Extension cords comply with specifications.
Circu# is equipped with a 15 amp circu# breaker or 15 amp
time delay fuse. NOTE: ff compressor is connected to a circu#
protected by fuses, use only time delay fuses. Time delay fuses
should be marked "D" in Canada and "T" in the US.
If any of the above conditions cannot be met, or ff operation of the
compressor repeatedly causes interruption of the power, it may be
necessary to operate it from a20 amp circuit. It is not necessary to
change the cord set.
Compatibility
Air tools and accessories that are run off the compressor must be
compatible with petroleum-based products. If you suspect that a
material is not compatible with petroleum products, an air line filter
for removal of moisture and oil vapor in compressed air is required.
NOTE: Always use an air line filter to remove moisture and oil vapor
when spraying paint.
Location
Place the air compressor in a clean, dry and well ventilated area
at least 12" (30.5 cm) away from the wall or other obstructions that
will interfere with the flow of air. Keep the compressor away from
areas that have dirt and/or volatile fumes in the atmosphere. These
impurities may clog the intake filter and valves, causing inefficient
operation.
The air compressor pump and shroud are designed to allow for
proper cooling. The ventilation openings on the compressor are
necessary to maintain proper operating temperature. Do not place
rags or other containers on or near these openings.
Place the air compressor on a flat surface resting on the rubber
feet.
NOISE CONSIDERATIONS
Consult local officials for information regarding acceptable noise
levels in your area. To reduce excessive noise, use vibration mounts
or silencers, relocate the unit or construct total enclosures or baffle
walls. Contact a DEWALT service center or call 1-800-4-DEWALT for
assistance.
12

ELECTRICAL
Refer to all safety instructions before using unit. Observe extension
cord safety instructions if necessary. Always move the On/Off
switch (A) to the OFF position before removing the plug from the
outlet.
TRANSPORTING
When transporting the compressor in a vehicle, trailer, etc., ensure
that the tank is drained and the unit is secured. Use care when driv-
ing to avoid tipping the unit over in the vehicle. Damage can occur to
the compressor or surrounding items if the compressor is tipped.
MOVING
When moving the compressor, grasp the handle and carry the com-
pressor as close to the body as possible.
_, WARNING: Risk of unsafe operation. Ensure proper footing and
use caution when carrying compressor to avoid a loss of balance.
PREPARATION FOR USE
Pre-Start Checklist (Fig. 1)
1. Ensure the On/Off switch (A) is in the OFF position.
2. Plug the power cord into the correct branch circuit receptacle.
See Voltage and Circuit Protection under Installation.
3. Ensure air tank is drained, see Draining Air Tank under
Maintenance.
4. Ensure the drain valve (H) is closed.
5. Ensure safety valve (G) is functioning properly, see Checking
Safety Valve under Maintenance.
6. Check pump oil level, see Compressor Pump Oil under
Maintenance.
CAUTION: Do not operate without oil or with inadequate oil. DEWALT
is not responsible for compressor failure caused by inadequate oil.
7. Turn regulator knob (D) counterclockwise until fully closed. Ensure
regulated pressure gauge reads 0 PSI (0 kPa).
8. Attach hose and accessories.
_kWARNING: Risk of unsafe operation. Firmly grasp hose in hand
when installing or disconnecting to prevent hose whip.
9. Ensure all covers and labels are in place, legible (for labels) and
securely mounted. Do not use compressor until all items have
been verified.
• , WARNING: Risk of bursting. Too much air pressure causes a
hazardous risk of bursting. Check the manufacturer's maximum
pressure rating for air tools and accessories. The regulator outlet
pressure must never exceed the maximum pressure rating.
Initial Set.up (Fig. 1)
WARNING: Do not operate this unit until you read and understand
this instruction manual for safety, operation and maintenance
instructions.
BREAK-IN PROCEDURE
_kWARNING: Serious damage may result if the following break-in
instructions are not closely followed.
This procedure is required before the air compressor is put into
service for the first time and when the check valve or a compressor
pump/motor has been replaced.
1. Ensure the On/Off switch (A) is in the OFF position.
NOTE: If hose is not connected to Quick Connect body, pull coupler
back until it clicks to prevent air from escaping through the quick
connect.
2. Plug the power cord into the correct branch circuit receptacle. See
Voltage and Circuit Protection under Installation.
13

3. Open the drain valves (counter-clockwise) fully to permit air to
escape and prevent air pressure build up in the air tank during
the break-in period.
4. Move the On/Off switch to the ON position. The compressor will
start.
5. Run the compressor for 20 minutes.
6. After 20 minutes, close the drain valves by turning clockwise.
The tank will fill to cut-out pressure and the motor will stop.
7. Compressed air will be available until it is used or bled off.
OPERATING PROCEDURES
Start-up (Fig. 1)
1. Follow Pre-Start Checklist under Preparation for Use.
2. Move the On/Off switch to the ON position and allow tank pres-
sure to build. Motor will stop when tank pressure reaches
cut-out pressure.
CAUTION: Risk of unsafe operation. Compressed air from the unit
may contain water condensation and oil mist. Do not spray unfil-
tered air at an item that could be damaged by moisture. Some air
operated tools or devices may require filtered air. Read the instruc-
tions for the air tool or device.
3. Adjust regulator (D) to desired setting. See Regulator under
Features.
Shut-down (Fig. 1)
1 Move On/Off switch (A) is in the OFF position. NOTE: If finished
using compressor, follow Steps 2 - 6.
2. Turn regulator knob (D) counterclockwise until fully closed. Ensure
regulated pressure gauge reads 0 PSI (0 kPa).
3. Remove hose and accessory.
4. Drain the air tank, see Draining Air Tank under Maintenance.
Ensure air tank pressure gauge reads 0 PSI (0 kPa).
_, WARNING: Risk of bursting. Drain air tank daily. Water will con-
dense in air tank. If not drained, water will corrode and weaken the
air tank causing a risk of air tank rupture.
5. Allow the compressor to cool down.
6. Wipe air compressor clean and store in a safe, non-freezing
area.
MAINTENANCE
The following procedures must be followed when maintenance or
service is performed on the air compressor.
1. Ensure On/Off switch is in the OFF position.
2. Remove air compressor plug from outlet.
3. Drain air tank.
4. Allow air compressor to cool down before starting service.
NOTE: All compressed air systems contain maintenance parts (e.g.,
oil, filters, separators) that are periodically replaced. These used parts
may contain substances that are regulated and must be disposed of in
accordance with local, state, and federal laws and regulations.
NOTE: Take note of the positions and locations of parts during
disassembly to make reassembly easier.
NOTE: Any service operations not included in this section should
be performed by a DEWALT factory service center or a DEWALT
authorized service center.
14

Maintenance Chart
Procedure Daily Weekly IVlonthly
Check safety valve X
Inspect air filter + X
Drain air tank X
Check pump oil level X
Change pump oil**+
Oil leak inspection X
Check for unusual noise! X
vibration
Check for air leaks* X
Clean compressor exterior X
1year or
200 Hours
* To check for air leaks apply a solution of soapy water around joints.
While compressor is pumping to pressure and after pressure cuts out,
look for air bubbles to form.
** The pump oil must be changed after the first 20 hours of operation.
Thereafter, when using DEWALT synthetic or SAE 40, non-detergent air
compressor oil, change oil every 200 hours of operation or once a year,
whichever comes first.
+ Performmore frequent !ndusty or humid condit!ons
Checking Safety Valve (Fig. 1)
_WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,
and surrounding parts are very hot, do not touch (see the Hot
Surfaces identified in Fig. 2). Allow compressor to cool prior to
servicing.
_WARNING: Risk of bursting, ff the safety valve does not work
properly, over-pressurization may occur, causing air tank rupture or
an explosion.
Before starting compressor, pull the ring on the safety valve to
make sure that the safety valve operates freely. If the valve is stuck
or does not operate smoothly, it must be replaced with the same
type of valve.
Checking Air Filter Element (Fig. 1)
_,WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head, and
surrounding parts are very hot, do not touch (see the Hot Surfaces
identified in Fig. 2). Allow compressor to cool prior to servicing.
1. Ensure the On/Off switch (A) is in the OFF position.
2. Allow unit to cool.
3. Remove air filter (N) from unit.
4. Carefully pry filter top from base.
5. Remove element from filter base.
6. If element needs cleaning, blow out with air. Replace if needed.
Purchase replacement parts from your local dealer or authorized
service center. Always use identical replacement parts.
7. Place element back in filter base.
8. Snap filter top to filter base.
9. Reassemble air filter to unit. Ensure exhaust outlet points down.
_CAUTION: Risk of unsafe operation. Do not operate without air
inlet filter
Draining Air Tank (Fig. 1)
_kWARNING: Risk of unsafe operation. Risk from noise. Air tanks
contain high pressure air. Keep face and other body parts away from
outlet of drain. Use safety glasses [ANSI Z87.1 (CAN/CSA Z94.3)]
when draining as debris can be kicked up into face. Use ear
protection [ANSI $12.6 ($3.19)] as air flow noise is loud when
draining.
15

NOTE: All compressed air systems generate condensate that
accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers).
This condensate contains lubricating oil and/or substances which
may be regulated and must be disposed of in accordance with local,
state, and federal laws and regulations.
1. Ensure On/Off switch is in the OFF position.
2. Move compressor into an inclined position so drain valve (H) is
at the lowest point (this will assist in removing moisture, dirt, etc.
from air tanks)
3. Place a suitable container under the drain valve to catch
discharge.
4. Grasp knurled knob on drain valve.
5. Slowly rotate knob to gradually bleed air from air tank.
_, WARNING: Risk of bursting. Drain air tank daily. Water will con-
dense in air tank. ff not drained, water will corrode and weaken the
air tank causing a risk of air tank rupture.
CAUTION: Risk of property damage. Drain water from air tank may
contain oil and rust, which can cause stains.
6. When air tank pressure gauge reads 10 PSi (68,9 kPa), rotate
valve to the fully open position.
7. Close drain valve when finished.
Compressor Pump Oil (Fig. 1)
CHECKING OiL
&WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,
and surrounding parts are very hot, do not touch (see the Hot
Surfaces identified in Fig. 2). Allow compressor to cool prior to
servicing.
1. Ensure On/Off switch is in the OFF position.
2. Place unit on a flat level surface.
3. Remove dipstick (K) and wipe clean.
16
4. Reinsert dipstick fully into oil fill port for a few
seconds to allow oil to collect on the dipstick. K
5. Remove oil dipstick to read oil level. Oil should
not exceed top raised line on dipstick. If oil is
below lower mark, add SAE 40, non-detergent
air compressor oil and follow Steps 4 - 6.
NOTE: When filling the crankcase, the oil
flows very slowly into the pump. If the oil is
added too quickly, it will overflow and appear
to be full.
_,CAUTION: Risk of unsafe operation. Overfilling with
oil will cause premature compressor failure. Do not
overfill.
6. Replace dipstick.
CHANGING OiL
NOTE: Pump oil contains substances that are MAX,
regulated and must be disposed of in accordance with
local, state and federal laws and regulations. MIN-
_&WARNING: Hot surfaces. Risk of burn. Aftercooler, pump head,
and surrounding parts are very hot, do not touch (see the Hot
Surfaces identified in Fig. 2). Allow compressor to cool prior to
servicing.
1. Ensure On/Off switch is in the OFF position.
2. Allow the unit to cool.
3. Remove air compressor plug from outlet.
4. Drain air tank.
5. Locate a suitable container under pump drain plug (L).
6. Remove the dipstick (K) from crankcase.
7. Remove the oil drain plug (L).
8. Allow ample time for all oil to drain out. (Tilting the compressor
towards the drain plug will assist in draining.)

9.Installtheoildrainplug.
10.FillpumpwithSAE40,non-detergentaircompressoroil.
11.Replacedipstick.
ACCESSORIES
Recommended accessories for use with your tool are available
for purchase from your local dealer or authorized service center.
If you need assistance in locating any accessory for your tool,
please contact DEWALT Industrial Tool Co., 701 East Joppa Road,
Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit
our website www.dewalt.com.
_kCAUTION: The use of any other accessory not recommended for
use with this tool could be hazardous. Use only accessories rated
equal to or higher than the rating of the air compressor.
SERP'IC_ INFORMATION
Please have the following information available for all service calls:
Model Number Serial Number
Date and Place of Purchase
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment should be performed by a DEWALT factory service
center, a DEWALT authorized service center or other qualified
service personnel. Always use identical replacement parts.
Full One Year Warranty
DEWALT heavy duty industrial tools are warranted for one year from
date of purchase. We will repair, without charge, any defects due
to faulty materials or workmanship. For warranty repair information,
call 1-800-4-DEWALT. This warranty does not apply to accessories
or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may
have other rights which vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold
in Latin America. For products sold in Latin America, see country
specific warranty information contained either in the packaging, call
the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-4-DEWALT for a free
replacement.
17

GLOSSARY
CFM: Cubic feet per minute.
SCFM: Standard cubic feet per minute; a unit of measure of air delivery.
PSI: Pounds per square inch; a unit of measure of pressure.
kPa (ki[opasca[): Metric pressure measurement. 1 kilopascal equal 1000 pascals.
Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified
independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety.
Cut-In Pressure: While the motor is off, air tank pressure drops when accessory is used. When the tank pressure drops to a certain low
level the motor will restart automatically. The low pressure at which the motor automatically restarts is called cut-in pressure.
Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a
certain high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The
high pressure at which the motor shuts off is called cut-out pressure.
Branch Circuit: The circuit carrying electricity from electrical panel to outlet.
Duty Cycle: This air compressor pump is capable of running continuously. However, to prolong the life of your air compressor, it is
recommended that a 50%-75% average duty cycle be maintained; that is, the air compressor pump should not run more than 30-
45 minutes in any given hour.
18

Troubleshooting Guide
This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or
maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified DEWALT technician or
your dealer.
Problem Code
Excessive air tank pressure-safety valve pops off ...................................................................... 1,2
Air leaks .................................................................................................................................... 3
Air leaks in air tank or at air tank welds .................................................................................... 4
Air leaks between head and valve plate .................................................................................... 5
Air leaks from safety valve ......................................................................................................... 6
Knocking Noise .......................................................................................................................... 6,16,17
Pressure reading on the regulated pressure gauge drops when an accessory is used ........... 7
Compressor is not supplying enough air to operate accessories .............................................. 8,9,10,11,12,15
Regulator knob has continuous air leak .................................................................................... 13
Regulator will not shut off air outlet ........................................................................................... 13
Moisture in pump crankcase ...................................................................................................... 14,18
Motor will not run ....................................................................................................................... 11,19,20,21,22,23,24,25,26
Troubleshooting Codes
CODE POSSIBLE CAUSE POSSIBLE SOLUTION
Pressure switch does not Shut off moto[ when compressor set the On/Off switch to OFF, if the unit does not ShUt
reaches Cut_out pressure off c0ntact a DEWALT faCt0rY Seiv!Ce center 0r a DEWALT
authorized service center.
2 Pressure switch cut-out too high Contact a DEWALT factory service center or a DEWALT
authorized service center.
19

CODE POSSIBLE CAUSE POSSIBLE SOLUTION
3 Tube fittings are not tight enough Tighten fittings Where air Can be heard eScaPingl cheCk
• fittings with soapy water solution. Do Not Overtighten.
4 Defective air tank Air tank must be replaced. Do not repair the leak.
&WARNING: Risk of bursting. Do not drill into, weld or
otherwise modify air tank or it will weaken. The air tank can
rupture or explode.
contact a DEWALT factory service cente[ 0r a DEWALT
• authorized Service center.
6 Defective safety valve Operate safety valve manually by pulling on ring. If valve
still leaks, it must be replaced.
Regulator is not adjusted coirect!y foi access0iY being, !t is norma! for some pressure drop to occur when an acceS'
used .............................. sory is used, adjust the regulator as instructed in Regulator
under Features if pressure drop s excessive.
, NOTE: Adjust the iegulated pressure undei fl0w cond!tionS
wh e accessory s be ng used.
8 Prolonged excessive use of air Decrease amount of air usage.
compressoi is n0t laige en0ugh f0i acceSSorY Check the accessory air reqUiremenL If it is higher than
the SCFM or pressure Supp!ied by your air Compress0r, a
larger compressor is needed to operate accessory.
10 Hole in air hose Replace air hose.
11 ' Check valve restricted Remove; Clean or replace.
12 Air leaks Tighten fittings.
13 Regulator is damaged Replace:
2O