DFG E-TitanComb User manual

Instruction Manual
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
DFG E-TitanComb
Heavy Duty
Binding Machine

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone: [phone], Fax: [phone]
Email: [e-mail] Website: www.dfgus.com
EtitanComb Machine Operation Manual
For your safety:
1. Do not connect this product to electrical power or attempt to operate it before you
read these operating instructions and have been fully trained to operate this
product.
2. Follow the instructions and warnings on the machine and on this operation
manual
3. When lifting the machine, you should only lift from the bottom
4. Indoor use only. Do not expose to rain.
5. Keep hands, long hair, neckties, necklaces and other loose articles away from
moving parts
6. Do not place this product on an unstable stand, cart, or surface. The product may
fall and hurt you. If you use a cart, move the product and cart carefully.
7. Do not insert objects or spill liquids into the product. They may short out
components that may result in fire.
8. The power outlet shall be installed near this product and shall be easily accessible.
9. Unplug the product before moving it. Unplug the power supplier when it will not
be in use for an extended period of time.
10. Do not attempt to service this product. Contact DFG or your dealer if you need
service.
This machine should only plug into 110 V single-phase power outlets.
1. Insert foot pedal plug into foot
pedal socket
2. Connect power cord to machine
and power outlet (not shown)
3. Turn on the power

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone: [phone], Fax: [phone]
Email: [e-mail] Website: www.dfgus.com
Picture 1
Picture 2
Determine Plastic comb binding element size
There are three methods you can use:
1. To use any size of comb you like, as long as the comb size is larger than book
thickness2.
2. To use coil that is 2 – 6 mm (1/8” to ¼”) larger than book thickness
3. To use our coil size selector. Please refer to the picture 3 (EtitanCoil machine
showed. only comb size up to 1 1/2” are showed)
Picture 3
A
B
Installation
1. Remove a screw (A) from binding shaft (see
picture 1) by a Philip (cross) head screwdriver.
2. Push binding handle (B) onto the binding shaft
(see picture 2).
3. Install the screw back
Put book on the table and under the
“Size Selector”.
Move the “Size Selector” down until
its bottom touches the top page of
sheet.
The point area of the “Size Selector”
will point the coil size you can use

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone: [phone], Fax: [phone]
Email: [e-mail] Website: www.dfgus.com
Determine Side Margin (side guide) and Punch Margin (rear back gage)
Picture 4
(EtitanCoil machine showed)
Punching
1. Align sheets and insert edge to be bound into punch throat
2. Push the sheets to flush against the inner wall of punch throat.
3. Push the sheets to be against the side guide
4. Press the foot pedal
You can punch up to 28 sheets of paper (20#) at once. Punch ONLY 6 pieces of 10 mil
PVC covers at a time to prevent jams and excessive wear.
Binding
Picture 5
.
1. Select the punch margin (general
guidance – the thicker the book, the
larger the punch margin. However,
you can use small punch margin for
any thickness of book)
2. Set the side guide to center the
sheet
1. Place a plastic comb-binding element on the
binding head. Please make sure that the tips of
the plastic rings are on the top and pointing away
from you (see picture 5)
2. Pull binding lever forward (towards you) to
open the plastic comb-binding element
3. Align the holes of the punched documents
with the tips of the plastic rings on the binding
element. Load the punched documents vertically
into the open plastic rings of the
binding element. Swing the documents down so
that the plastic rings will enter the punched holes
of the documents.
Tip

1260 Kempar, Madison Heights, MI 48071, U.S.A. Phone: [phone], Fax: [phone]
Email: [e-mail] Website: www.dfgus.com
Empty chip drawer
Please empty chip drawer frequently to prevent machine jam. Pull the drawer toward you
to open.
Service
For service or warranty, please contact DFG at:
Phone: [phone]
Email: [email protected]
Thank you for purchasing DFG EtitanComb machine.
4. Pushed the binding lever to its original position. The binding element will close and
bind the documents
5. Remove bound documents by lifting it up from you binding head.