DHP 4032459 User manual

DO NOT RETURN TO THE STORE !
Visit www.dhpfurniture.com/eng/support-home
or call Toll-Free 1-800-267-1739
4032459
B34403245904 - 241643 -XL
Date of Purchase
Upholstered Daybed and Trundle
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
XL - 2017.09.15
© 2014 Dorel Home Products All Rights Reserved
Twin
Grey
Weight Limit: 400 Lb / 181 Kg
TM
Daybed
225 Lb / 102 Kg Trundle

Contact Us!
[e-mail]
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec, Canada H1G 3L1
Read Before Beginning Assembly
1-800-267-1739
Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)
Warranty Information
2
Caution
DHP warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers one year from the date of
original purchase. This is solely limited to the repair or replacement of defective
parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way.
Liability for consequential damages is excluded to the extent exclusion is permitted
by law. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
To obtain warranty service, purchaser must present original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty
period only. The defective components will be repaired or replaced without charge,
subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
● Call our toll free number if you need assistance.
● Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
● Recommended # of people needed for assembly: 2 (however it is always better
to have an extra hand). Estimated assembly time is 2 hours.
● Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
● Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
● This product is designed for home use and not intended for commercial use.
● This product contains small components. Please ensure that they are kept away
from small children.
● Do not use power tools to assemble your furniture. Power tools may strip or
damage the parts.
For help with assembly, identifying parts, product information or to order parts,
please contact us:

3

4
Parts For Daybed
This item is packed in 2 boxes!
All parts listed on this page are in Box A.
If Box B is missing please contact your Retailer.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
C
C
C
Armrest
T936770
X 2

5
Parts For Daybed
This item is packed in 2 boxes!
All parts listed on this page are in Box B.
If Box A is missing please contact your Retailer.
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
Front/Rear Panel
T932980
X 2
BEF
K
Front/Rear Rail
T926920
X 2
Center Rail
T936800
X 1
Cross Brace
T926830
X 1
Wooden Slat
T926360
X 26
Bracket
T393050
X 2
Bracket
T393060
X 2
Single Slat Cap
T926370
X 26
Double Slat Cap
T926380
X 13
Leg
T926840
X 4
O
S T XY
Z
B
B
EFKX
Y
Z
T
S
O

6
Parts For Trundle
This item is packed in 2 boxes!
All parts listed on this page are in Box B.
If Box A is missing please contact your Retailer.
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
G
G
H
I J
NP
O
XY
Wooden Slat
T926360
X 24
Single Slat Cap
T926370
X 24
Double Slat Cap
T926380
X 12
Side Rail
T951010
X 2
Caster
T950950
X 2
Lock Caster
T950960
X 2
Front panel
T932990
X 1
Rear Rail
T926340
X 2
Front Rail
T926350
X 1
H
H
P
N
J
I
I
X
O
Y

7
Hardware Pack: Daybed
Hardware Pack #: T4032359-00
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of
the page.
45
3
21
1/4" X3/4"
X 14
1/4" X 1 3/16"
X 16
1/4" X 1 9/16"
X 12
5/16" X 3 1/8"
X 4
4mm
X 1

8
Hardware Pack: Trundle
Hardware Pack #: T4144719LS-01
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of
the page.
1
1/4" X3/4"
X 8
2
1/4" X 1 3/8"
X 6
3
1/4" X 1 9/16"
X 6
4
1/4"
X 6
5
4mm
X 6
6
Wrench
X 6

9
Step 1
NOTE: The following instructions will
illustrate how to assemble the Daybed
from Step 1 to Step 6. Please use the
Daybed Hardware Pack: T4032359-00.
Attach Z x 4 to C x 2 with x.
X 4
Z
ZZ
Z
4
To avoid fraying the fabric during the assembly,
please lay the armrests(C) on a piece of cardboard.
CC

10
Step 2
Attach T and S to B with u.
NOTE: This step needs to be done
twice for remaining parts B, S and T.
X 12
B
T
S
BB
TS
Pay special attention that small holes on slots
of S and T should be facing upward!
1
x 2

11
Step 3
Attach E to B with w.
NOTE: This step needs to be done
twice for remaining parts E and B.
X 12
B
E
3
Please make sure narrow holes on part T, S and slat
holes on part E are facing toward the same side.
T
S
x 2

12
Step 4
4.1 Pre assemble v in C;
4.2 Hang S and T located on part B onto
pre-assembled v, as illustrated below.
Do not completely tighten the bolts in this
step as you need to assemble the middle
stretcher F in the next step.
X 12
CCC
B
T
B
T
B
B
C
C
T
4.1 4.2
2
Leave half of the thread exposed！

13
Step 5
5.1 Attach F to C with v;
5.2 Attach K to E with u.
Completely tighten all bolts from step 4
in this step.
X 4
2
C
C
F
C
B
E
K
E
K
1
X 2
1
2
5.1 5.2
F

14
Step 6
O
O
X
E
XY
O
O
F
O
E
X
E
F
Y
X
6.1 6.2 6.3
6.1 Insert O into X;
6.2 Press X into E, repeat the same procedure
for the opposite side.
6.3 Insert ends of both slat O into Y, then
press Y into F as illustrated.
Repeat the same procedures going backwards
for every row of slats.

15
Step 7
J
I
I
H
H
I
J
IH
H
H
H
H
The following instructions will illustrate how
to assemble the Trundle from Step 7 to Step
11. Please use the Trundle Hardware Pack:
T4144719LS-01.
7.1 Lay H x 2 on the floor with holes towards
upward as illustrated.
7.2 Lay J and I x 2 with the slat holes facing
downwards.
7.3 Insert H x 2 into I x 2 and J as illustrated.
Caster holes on H
towards upward.
Slat holes on part I / J
towards floor as illustreated.
7.1
7.2
7.3

16
Step 8
Attach I x 2 & J to H x 2 with v using y
and x using z.
46
2
5
J
H
6
5
2
I
H
4
I
I
J
H
H
2
4
X 6 X 6

17
Step 9
H
P
IJ
H
N
I
I
J
H
H
N
N
P
P
1
X 8
In order not to damage
your product, please orient
lever to the inside of the
trundle as illustrated.
Attach P x 2 & N x 2 to H x 2 with u.
Caster N should be assembled
close to Part J.

18
Step 10
G
J
J
I
I
G
3
X 6
Turn over the frame assembled from
STEP 9.
Attach G to J with w.

19
Step 11
I
Y
O
O
J
X
O
X
I
O
I
X
X
YJ
11.1 11.2 11.3
11.1 Insert O into X;
11.2 Press X into J, repeat the same
procedure for the opposite side to Press X
into I;
11.3 Insert ends of both slats O into Y,
then press Y into I as illustrated. Repeat the
same procedures going backwards for every
row of slats.
O

20
Helpful Hints
To use Trundle:
Pull out the trundle completely from
underneath daybed. Once positioned,
make sure casters are locked by pushing
down the lever "ON" as illustrated "How to
lock caster?".
To store Trundle:
Unlock the casters by pushing down the
lever "OFF" as illustrated "How to unlock
caster?" and push in the Trundle
underneath the Daybed.
WARNINGS:
Keep casters in lock condition under normal
use to prevent unintentional movement which
may lead to instability and tipping.
How to unlock caster?
How to lock caster?