Royalcraft Walton Love Seat User manual

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 1 / 6

www.ro
y
alcraft.co.uk
Product size:
W147*D60.5*H75 cm
The frame of this product is manufactured from mild steel coated with a weather resistant paint.
Steel has a natural tendency to rust over time and, whilst we expect you to be able to enjoy your
furniture for many years to come, we recommend that you check the product from time to time for
signs of paint damage and/ or rust. If the paint should become damaged, or if rust begins to form,
you should clean the affected area and apply a suitable “thinners based” touch-up paint.
Such paints are readily available from all good hardware and DIY stores.”
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 2 / 6

www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
This product is intended for domestic use only.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Remove all packaging and banding and place the components
carefully on suitable surfaces to prevent damaging or scratching
them.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
This product is suitable for all year outdoor use, but we
recommend that a furniture cover be used to add additional
protection to your product when not in use.
During severe weather conditions and in the winter months we
recommend moving your furniture inside into a cool, dry place.
Before storage, ensure that the product is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, dry cloth.
Cushions should be cleaned following the care instruction on the
label.
Don’ts
Do not use scourers, abrasives, washing powders, chemical cleaners
or any other substances containing abrasives since these substances
can damage the product, including the glass panel.
Never tilt the chair during use.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the glass as a chopping surface. Do not strike glass
with hard or pointed items.
Do not strike the glass with hard or pointed items.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not sit or lean on the table.
Do not stand or climb onto the product and do not use it as a ladder,
as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people.
Time to assemble
40 minutes
Tools required


Tips:
Do NOT fully tighten bolts before
all components are connected.
Only fully tighten once you are
satisfied with the alignment of all
components.
Do not overtighten bolts.

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 3 / 6

www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A

LeftLeg
1 PC B

RightLeg
1 PC
C

Seating
1 PC D

Left Backrest
1 PC
E

RightBackrest
1 PC F

TableTop(withdetachable
glass)
1 PC
G

Long Table Leg
2 PCS H 
ShortTableLeg
2 PCS
I
M6*15mm Bolt
16
PCS J
M6*20mm Bolt
2 PCS

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 4 / 6

www.ro
y
alcraft.co.uk
K
M6*25mm Bolt
10
PCS L

Spacer
2 PCS
M

BoltHeadCap
28
PCS
N
M6 Washer
28
PCS
O
Spanner
1 PC
Step by step assembly instructions
Note: All Bolt Head Caps and Nut Caps should not be attached before finally tightening all Bolts with
Spanner or Allen Key (optional).
Only tighten all bolts when you are satisfied with the alignment of all components.
Step One
Assemble the Seating (C) to the
Left Leg (A) and Right Leg (B)
using Washers (N), Bolts (I) and
Bolt Head Caps (M).

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 5 / 6

www.ro
y
alcraft.co.uk
Step Two
Assemble the Left Backrest (D) and
Right Backrest (E) to the Left Leg (A),
Right Leg (B) and Seating (C).
using Washers (N), Bolts (K) or (J) and
Bolt Head Caps (M).
Please note the location of Bolts (K) and (J).
Step Three
Assemble the Short Table Leg (G) and
Long Table Leg (H) to the Seating (C).
using Washers (N), Bolts (K) and
Bolt Head Caps (M).
Assemble the Table Top (F) onto the
Short Table Leg (G) and
Long Table Leg (H) using Washers (N),
Bolts (I) and Bolt Head Caps (M).
Assemble the Table Top (F) onto the
Left Backrest (D) and Right Backrest (E)
using Washers (N), Bolts (K) ,
Bolt Head Caps (M) and Spacers (L).
Your Love Seat is ready for use!

Walton Love Seat
Assembly Instructions
ProducedinChinaforA.Mir&Co.,Ltd.
© A. Mir & Co., Ltd. 6 / 6

www.ro
y
alcraft.co.uk
Note: A suitable parasol base should be used if
a parasol is used.
Never tilt the Love Seat during use.
Ensure the product is always placed firmly
on the ground.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE