Digi ConnectTank v1 User manual

1Identify Contents
Quick Start Guide
Digi ConnectTank v1
b
Digi Connect Tank Magnet
If any item is missing or damaged, please contact your supplier. Also, make a record of any damage that may have occurred during shipping and
report it to the supplier.
Note:For the bulk packs (12 ConnectTanks), only one magnet is included in
the kit.
DiGI International
www.digi.com
Unscrew the four retaining screws and remove the enclosure cover.
2Insert the SIM Card and Connect the Battery
a
Unlock the SIM card holder. Insert the SIM card, and lock as demonstrated in the following image.
Digi Connect Tank is available in both CDMA and UMTS models. SIM card holders are used only for the UMTS models of Digi
Connect Tank. For information on SIM card activation, refer to the Digi ConnectTank Getting Started Guide.
Connect the internal battery to the device. Ensure the battery and its wiring are properly placed in the wiring compartment.
Re-attach the enclosure cover, and secure using the original retaining screws.
f
LOCK
OPEN
LOCK
OPEN
OPEN
LOCK
LOCK
OPEN
A SIM card must be supplied and activated by a Cellular Service Provider for device operation.
Note: The metal contacts on the SIM card should be face down, and the chamfered edge should be on the top.
(for Verizon users only).
Press the wake up button followed by the factory default button.
The network LED will blink red (2 seconds ON- 2 seconds OFF) until authentication is complete.
Aer authentication, the network LED will blink blue (2 seconds ON- 2 seconds OFF) for 30 seconds.
Upload the device information to the Device Cloud.
First reset the device using the reset button and wait for 30 seconds.
Then press the factory default button to restore factory settings and register the device in the Device Cloud.
Wait for the network LED to glow for 3 seconds.
Register the device to the network
Before completing installation, make sure the Tank Upload Method matches your cellular contract to avoid a high cellular bill. See the Digi Connect Tank
Getting Started Guide for more information.
Tips
Installation
Note: Cover screws are required as part of the safety rating. When tightening the cover screws,
use a screw torque of 7 to 17 inch pounds (0.79 to 1.92 newton meters).
a
b
c
d
e
f
90001316 G

© 2015 Digi International Inc.
Digi, Digi International Inc., Connect Tank, and the Digi logo are trademarks or registered trademarks of Digi International Inc., in the United States and other countries worldwide.
3Mount the Digi Connect Tank
4
What’s Next?
The Digi ConnectTank can be connected directly to tanks with a 1" NPT threaded opening as shown in the following image.
Note: For tanks with a 2" NPT threaded opening, first connect a 1-to-2" NPT adapter to the Digi
ConnectTank, then attach the unit to the tank as shown in the image.
Before you wake-up the device, register the device to the Device Cloud. For more information, see Adding Digi ConnectTank Device in Device Cloud section
of the Digi ConnectTank Getting Started Guide. Once you have connected the internal battery, installed the device and powered it ON, press the Wake up
button. You can also activate the Wake up button using the magnet.
The network and battery LEDs will glow indicating the status of the unit.
The device is now ready for use. Now you are ready to change the configuration. For more information, see the Configuration section of the Digi
ConnectTank Getting Started Guide.
)
)
)
DiGI International
www.digi.com
Battery LED Cellular LED
Battery LED Cellular LED
Note: There may be a delay in LED activity for 20-90 seconds.
Configure the Digi ConnectTank with Device Cloud
To complete configuration of your device, refer to the Digi Connect v1 Tank Getting Started Guide provided on the Digi support site
(www.digi.com/support).
LED Color and Light Pattern Description
Battery LED Blink Blue Battery health – strong.
Blink Red
Battery health – weak.
Cellular LED Blink Blue (1 sec ond ON - 1 second OFF) Registered to the cellular network .
Blink Red Not r egistered to the cellular
network or registration has failed.
Glow Blue (for 3seconds) Diagnostic record has been
successfully sent to the Device Cloud.
Cellular LED (d uring
Verizon activation)
Blink Red (2 sec onds ON - 2 seconds OFF) Authentication is in progress .
Blink Blue (2 sec onds ON - 2 s econds OFF
for 30 seconds)
Authentication is successful .