Digicom 10/100 User manual

PCI CARD 10/100
User’s Guide
Dear customer,
thank you for purchasing a Digicom product.
DESCRIPTION
With your Digicom PCI Card 10/100 network card you can connect your
PC to a Local Area Network regardless of its operating speed (10 or 100
Mbit/s).
UsingPCIcard10/100 willbring severaladvantages thanksto itsadvanced
features and simple installation:
lPlug and Play
lAutosensing,operating speedis automaticallydetected assoon ascable
is plugged
lFull Duplex at 10 and 100Mbit/s
lWake On Lan function
lDriver support for most common operating systems
PACKAGE CONTENTS
lPCI Card 10/100
lUser Guide
lWake On Lan cable
lDriver diskette
PREFACE
The following installation rules should be respected in order to have the
best working order of the equipment and for the user’s safety.
ENVIROMENTAL CONDITIONS
ENVIROMENTAL TEMPERATURE RELATIVE HUMIDITY
from 0 to + 55°C from 5 to 95% n.c.
from 32 to 131°F
Rapid changes of temperature or humidity should be avoided (0,03°C/
min).
lDust, humidity, heat from direct sun light.
lObjectswhich irradiateheat.Thesecouldcausedamageto thecontainer
or other problems.
lObjects which produce a strong electtromagnetic field (loudspeakers,
etc.)
lLiquids or chemical corrosive substances.
http://www.digicom.it
DECLARATION OF CONFORMITY
This product satisfies the basic requirements of Electromagnetic
Compatibility and Safety of the below indicated Directive:
l89/336/CEE of 3 May 1989 with subsequent modifications (Directive
92/31/CEE of April 28, 1992, Directive 93/68/CEE of July 22,1993 and
Directive 93/97/CEE of 29 October 1993).
l73/23/CEE of February 19, 1973 with subsequent modifications
(Directive 93/68 ECC of July 22, 1993).
CHECK REPORT
The equipment has been successfully tested according to the check
procedure indicated on the inside back cover of the user’s manual. It is in
conformitywiththetechnicalcharacteristics describedin theusers’ manual
supplied with the equipment.
WARRANTY
WARRANTY CLAUSES
lThe equipment has a warranty which covers manufacturing and
operating faults for the period indicated on the inside back cover of the
user’s manual.
lThe warranty is to be considered freight forward and the goods must
reach the address indicated below at customer’s expences.
lWarranty means the substitution or repairing of fault products. Working
hours used for repairing included in the warranty.
lThe estetic and the separable parts are not included in the warranty.
lThe warranty is not extended to equipments which have been subject
to misuse, improper installation, electric discharge or repaired by
unauthorized staff.

TECHNICAL SPECIFICATIONS
lPCI Local Bus Rev. 2.0
l32 bit bus mastering PCI
lEarly transmit & receive interrupt support
lUp to 33MHz clock support
lRJ45 port
lCategory 3, 4, 5 cabling for 10BaseT
lCategory 5 for 100BaseTX
lIEEE802.3 for 10BaseT, IEEE802.3u for 100BaseTX
l10/100 Mbps auto-sensing
lFull duplex on 10 and 100 Mbps networks
lWake On Lan remote power on
lACPI, Advanced Configuration Power Interface
lSleep mode left by keyboard or wake up packet
lAutomatic Bios I/O address allocation
lIRQ 0Ah mapped to Bios IRQ Setup
lWake On Lan through included cable
lBoot ROM socket
lActivity, Link, 10Mbps/100Mbps led indicators
l5 VDC, max 300mA
lOperating Temperature 0 to 55°C - 32 to 131 F
lHumidity 10% to 95% non condensing
lCE Mark
lDriver support for Microsoft Windows® 3.11, Windows®, 98/95/95-
OSR2, Windows® NT 3.51/4.0, Microsoft Lan Manager, IBM LAN
Support, OS2, OS2/WARP, LAN Server, SCO Unix, SUN PC-NFS,
ArtisoftLANtastic, BanyanVINES, DECPathworks, FTPPC/TCP, NCSA
TCP/IP, Novell NetWare 3.12, 4.x, 5.0, LAN Workplace, LANAnalyzer
HARDWARE INSTALLATION
Please refer to your PC documentation in order to correctly identify a Bus
Mastering PCI slot and the “5V Standby” connector for Wake On Lan
functionality. Also see the Setup/Bios documentation regarding PCI slots
and their settings.
To install the PCI Card 10/100, power off your PC and remove the chassis
cover. Next, select an unused PCI expansion bus slot and remove its
protective bracket. Carefully insert the card and press until all the edge
connectors are firmly seated inside the slot. Screw the card’s bracket
securely into the PC’s chassis and replace the cover.
If you are going to use the Wake On Lan capability, attach one end of the
3-pin Wake-on-LAN cable to the connector on the top edge of the card,
and the other end to the “5V Standby”
connector on the computer’s
motherboard.
Connect the PCI Card 10/100 to a
10Base-T or 100Base-TX hub or
switch using RJ45-RJ45 UTP cables
(Category 3, 4 or 5 for 10BASE-T;
Category 5 for 100BASE-TX).
The maximum allowable length of
10BASE-T or 100BASE-TX cable
connections is 100 meters (328 ft.).
SOFTWARE INSTALLATION
The PCI Card 10/100 should
beautomaticallyconfiguredby
the PCI computer’s BIOS
setup program.
However, if you have an
older PCI computer, you
may have to change the
computer’s BIOS settings
to accomplish this.
Please refer to section
“Setup and Diagnostics”.
Windows® 98/95
At startup your PC will
automaticallydetect anew
hardware and ask for the
drivers.
Click on Next.
Insert the driver disk into the
floppy drive, type A:\ and click on
Browse. Select Win95 or Win98
folder.
Click on OK.
Follow the instructions to
complete the installation.
OTHER OPERATING SYSTEMS OR APPLICATIONS
All drivers regarding supported operating systems and applications are
located in dedicated folders on the diskette.
Refer to the Release.txt file on the diskette for more details and general
informations.
Where needed a *.TXT file provides specific installation and use details.
SETUP AND DIAGNOSTICS
From the DOS prompt (not from a DOS window under Windows®) run
DIAG.EXE, available in the SETUP folder on the diskette.
Through View current configuration and Set New Configuration menues
you can check the current settings and modify them to match your needs.
Note: IRQ and I/O Base are controlled by the PC’s Bios.
Test andDiagnostic functionsareavailable fortesting andtroubleshooting.
Please refer to DIAG.TXT file for more detailed informations.
LED DESCRIPTION
Link 10
On when the card is correctly connected
and operating at 10Mbit/s.
Link 100
On when the card is correctly connected
and operating at 100Mbit/s.
ACT
Flashing when data is transmitted or
received.
Pin assignment
1 RD+
2 RD -
3 TD+
4 not used
5 not used
6 TD -
7 not used
8 not used
RJ45
Wake on LAN