Digiplex DGP-48 User manual

Digiplex Control Panel - V2.14/2.20ACC
DGP-48
Reference and Installation Manual

TABLE OF CONTENTS
INTRODUCTION.................................................................................................................................41.0
1.1 Features .......................................................................................................................................................... 4
1.2 Specifications .................................................................................................................................................. 4
ACCESSORIES ..................................................................................................................................52.0
INSTALLATION...................................................................................................................................73.0
3.1 Location & Mounting ....................................................................................................................................... 7
3.2 Earth Ground .................................................................................................................................................. 7
3.3 AC Power ........................................................................................................................................................ 7
3.4 Backup Battery ............................................................................................................................................... 7
3.5 Auxiliary Power Terminals .............................................................................................................................. 7
3.6 Telephone Line Connection ............................................................................................................................ 7
3.7 Bell/siren Output ............................................................................................................................................. 7
3.8 Calculating Power Requirements ................................................................................................................... 9
3.9 Programmable Outputs .................................................................................................................................10
3.10 Bus Zone Connections ............................................................................................................................... 11
3.11 Single Zone Connections ............................................................................................................................ 11
3.12 Double Zone Connections .......................................................................................................................... 12
3.13 Keypad Zone Connections ......................................................................................................................... 12
3.14 Keyswitch Connections ............................................................................................................................... 12
3.15 Fire Circuits ................................................................................................................................................. 12
3.16 Connecting the ZX4 .................................................................................................................................... 13
PROGRAMMING METHODS ...........................................................................................................14 4.0
4.1 Panel Programming Mode ............................................................................................................................ 14
4.2 Module Programming Mode ......................................................................................................................... 14
4.3 Feature Select Programming ........................................................................................................................ 14
4.4 Decimal Programming .................................................................................................................................. 14
4.5 Hexadecimal Programming .......................................................................................................................... 14
4.6 Level Programming ....................................................................................................................................... 14
4.7 Paradox Memory Key ................................................................................................................................... 15
ZONE PROGRAMMING ...................................................................................................................16 5.0
5.1 Zone Numbering ........................................................................................................................................... 17
5.2 Zone Definitions ............................................................................................................................................ 17
5.3 Zone Partition Assignment ............................................................................................................................ 18
5.4 Zone Options ................................................................................................................................................ 18
5.5 Input Speed .................................................................................................................................................. 19
5.6 EOL Zones .................................................................................................................................................... 19
5.7 Zone Doubling (ATZ) .................................................................................................................................... 20
KEYSWITCH PROGRAMMING........................................................................................................21 6.0
6.1 Keyswitch Numbering ................................................................................................................................... 22
6.2 Keyswitch Definitions .................................................................................................................................... 22
6.3 Keyswitch Partition Assignment .................................................................................................................... 22
6.4 Keyswitch Options ........................................................................................................................................ 22
ARMING & DISARMING OPTIONS..................................................................................................23 7.0
7.1 Arming Follows Partition ............................................................................................................................... 23
7.2 No Arming On Battery Fail ............................................................................................................................ 23
7.3 No Arming On Tamper .................................................................................................................................. 23
7.4 No Arming On Supervision Loss ................................................................................................................... 23

7.5 Timed Auto-Arming ........................................................................................................................................23
7.6 No Movement Auto-Arming ...........................................................................................................................23
7.7 Auto-Arming Options .....................................................................................................................................24
7.8 One-touch Features .......................................................................................................................................24
7.9 Exit Delay ......................................................................................................................................................24
7.10 Keypad Lock-out Feature ............................................................................................................................24
7.11 Maximum Bypass Entries ............................................................................................................................25
7.12 Display “Bypass” If Armed ...........................................................................................................................25
7.13 Bell Squawk .................................................................................................................................................25
7.14 Ring-back ....................................................................................................................................................25
7.15 Switch To Stay Arming ................................................................................................................................25
ALARM OPTIONS.............................................................................................................................26 8.0
8.1 Bell/alarm Output ...........................................................................................................................................26
8.2 Bell Cut-off Timer ...........................................................................................................................................26
8.3 Wireless Transmitter Supervision Options ....................................................................................................26
8.4 Tamper Recognition Options .........................................................................................................................26
8.5 Keypad Panic Options ...................................................................................................................................27
EVENT REPORTING ........................................................................................................................28 9.0
9.1 Reporting Enabled .........................................................................................................................................29
9.2 Report Codes ................................................................................................................................................29
9.3 Central Station Phone # ................................................................................................................................31
9.4 Partition Account # ........................................................................................................................................31
9.5 Reporting Formats .........................................................................................................................................31
9.6 Event Call Direction .......................................................................................................................................32
9.7 Recent Close Delay .......................................................................................................................................32
9.8 Auto Test Report ...........................................................................................................................................32
9.9 Power Fail Report Delay ................................................................................................................................32
9.10 Disarm Reporting Options ...........................................................................................................................32
9.11 Zone Restore Report Options ......................................................................................................................32
9.12 Pager Delay .................................................................................................................................................32
9.13 Auto Report Code Programming .................................................................................................................33
DIALER OPTIONS.............................................................................................................................3410.0
10.1 Telephone Line Monitoring ..........................................................................................................................34
10.2 Tone/pulse Dialing .......................................................................................................................................34
10.3 Pulse Ratio ..................................................................................................................................................34
10.4 Busy Tone Detection ...................................................................................................................................34
10.5 Switch To Pulse ...........................................................................................................................................34
10.6 Bell On Communication Fail ........................................................................................................................34
10.7 Dial Tone Delay ...........................................................................................................................................34
PROGRAMMABLE OUTPUTS..........................................................................................................3511.0
11.1 PGM Activation Event ..................................................................................................................................35
11.2 PGM Deactivation Option ............................................................................................................................35
11.3 PGM1 Is Smoke Input .................................................................................................................................36
PGM PROGRAMMING TABLE.........................................................................................................3712.0
SYSTEM SETTINGS & COMMANDS...............................................................................................4013.0
13.1 Hardware Reset ...........................................................................................................................................40
13.2 Software Reset ............................................................................................................................................40
13.3 Battery Charge Current ...............................................................................................................................40
13.4 Installer Code Lock ......................................................................................................................................40
13.5 Partitioning ...................................................................................................................................................40

13.6 Installer Function Keys ............................................................................................................................... 40
13.7 System Date & Time ................................................................................................................................... 41
13.8 Shabbat Feature ......................................................................................................................................... 41
13.9 Access Control ............................................................................................................................................ 41
13.10 Module Reset ............................................................................................................................................ 41
13.11 Locate Module .......................................................................................................................................... 41
13.12 Module Programming ............................................................................................................................... 41
13.13 Module Broadcast ..................................................................................................................................... 41
13.14 Remove Module ........................................................................................................................................ 41
13.15 Serial Number Viewing ............................................................................................................................. 41
13.16 Power Save Mode .................................................................................................................................... 42
13.17 Auto Trouble Shutdown ............................................................................................................................ 42
13.18 No AC Fail Display .................................................................................................................................... 42
ACCESS CODES..............................................................................................................................4314.0
14.1 Installer Code .............................................................................................................................................. 43
14.2 Access Code Length ................................................................................................................................... 43
14.3 System Master Code .................................................................................................................................. 43
14.4 Programming Access Codes ...................................................................................................................... 43
14.5 User Options ............................................................................................................................................... 43
14.6 User Partition Assignment .......................................................................................................................... 44
14.7 Access Control ............................................................................................................................................ 44
14.8 Multiple Action Feature ............................................................................................................................... 44
WINLOAD SOFTWARE....................................................................................................................4515.0
15.1 Answering Machine Override ...................................................................................................................... 45
15.2 Ring Counter ............................................................................................................................................... 45
15.3 Panel Identifier ............................................................................................................................................ 45
15.4 PC Password .............................................................................................................................................. 45
15.5 PC Telephone Number ............................................................................................................................... 45
15.6 Call WinLoad .............................................................................................................................................. 45
15.7 Answer WinLoad ......................................................................................................................................... 45
15.8 Event Buffer Transmission .......................................................................................................................... 45
15.9 Call Back Feature ....................................................................................................................................... 45
USER FEATURES............................................................................................................................4616.0
16.1 Arming and Disarming Features ................................................................................................................. 46
16.2 Bypass Programming .................................................................................................................................46
16.3 Chime Zones .............................................................................................................................................. 47
16.4 Access Codes ............................................................................................................................................. 47
16.5 Normal and Confidential Modes ................................................................................................................. 47
16.6 Keypad Settings .......................................................................................................................................... 47
16.7 Trouble Display ........................................................................................................................................... 48
16.8 Event Record Display .................................................................................................................................49
INDEX ...............................................................................................................................................5017.0
FCC WARNINGS..............................................................................................................................5418.0
WARRANTY......................................................................................................................................5519.0

4REFERENCE& INSTALLATIONMANUAL
1 INTRODUCTION
Paradox Security Systems has once again redefined the
boundaries of the security industry and is proud to introduce the
Digiplex Control Panel. A new generation in control panel
technology, the Digiplex Control Panel uses a quad-wire
communication bus that provides power and two-way
communication for up to 95 modules (keypads, motion detectors,
expansion modules, etc.). This, combined with four true partitions,
event call direction and the zone numbering feature, simplifies the
task of installing or making changes to your security system. The
innovative new programming method makes programming the
control panel logical and much simpler to execute. This new
generation of control panels offers increased capabilities with
countless new features without compromising its user-friendliness.
If anything, these new control panels are easier to use and easier
to install, making the Digiplex Control Panel the ultimate in reliable
security protection.
1.1 FEATURES
•Four-wire Communication Bus:
uProvides power and two-way communication to all
modules connected to the bus.
u95 module support
uAll bus modules have Plug and Play capability
uConnect modules up to 3000ft (914m) from the
control panel.
uFull System Supervision.
•48 fully programmable zones
•8 independent keyswitch zones (does not use any of the 48
zones)
•4 on-board hardwired input terminals for use with non-bus
detection devices (expandable to 48).
•4 True Partitions:
Most features and options in the Digiplex System can be
independently set for each partition such as event
reporting, entry/exit delay, bell squawk, quick arming,
panics and many more. All zones, keyswitches, user
codes and keypads are assigned to specific partitions,
making this a true partitioned system.
•95 User Codes, 1 Installer and 1 System Master
•Up to 4 fully programmable outputs (PGMs) are available.
PGM1 can be set as a two-wire smoke detector input. Optional
5A relay also available.
•Simple, direct and logical programming
•Event Call Direction:
The Digiplex Control Panel events are divided into three
event groups for each partition and two system event
groups. Each event group can be programmed with a
separate dialing sequence for each partition.
•4 Central Station Telephone Numbers
•SIA, Contact ID, Pager Format and many more Communicator
Formats
•Upload/download capability using new WinLoad Security
System Management software for Windows®.
•And much, much, more…
1.2 SPECIFICATIONS
CONTROLPANEL
•AC Power: 16VAC, 20/40VA, 50-60Hz
•Battery: 12VDC, 4Ah minimum
•Aux. Power: 12VDC 600mA typical, 700mA maximum,
fuseless shutdown at 1.1A
•Bell Output: 1A, fuseless shutdown @ 3A
•PGM Output: PGM1 (100mA), PGM2 - PGM4 (50mA) and
PGM5 (5A optional relay)
•Event Buffer: 1024 events
•All control panel outputs are rated to operate between 10.8Vdc
and 12.1Vdc

DIGIPLEX CONTROLPANEL5
2 ACCESSORIES
The following modules are compatible with the Digiplex DGP-48 Control Panel.
WINLOAD
This Windows®-based Security System Management Software can perform remote diagnostics and
adjustments, provide on-site communication at 300baud with the ADP-1 or at 19,200 baud with the
306 Adapter, facilitate programming and event loading, and customize control panel default settings.
This user-friendly software is compatible with most modems.
LCD KEYPAD (DGP-641)
48-zone, 32-character programmable LCD keypad that connects to the bus. Most messages in the
LCD keypad are programmable. View zone, event and trouble status for one or more partitions,
display entry/exit delay, adjust contrast, backlight, and many other features. On-board PGM output
and hardwired zone input.
ACCESS CONTROLLCD KEYPAD (DGP-641ACC)
The DGP-641ACC is an LCD Keypad that can be used with the Access Control feature available
through the Digiplex Control Panel. The Access Control feature allows you to monitor and control the
access of up to 32 doors in the Digiplex system. The DGP-641ACC is the same as a DGP-641
except it allows you to program the access control features, view logged access events as well as
communicate the status of a Posiprox (CR-R880) card reader, a Paradoor (460), a door lock, and a
door contact to the Digiplex system.
LED KEYPADS(DGP-610, DGP-620 & DGP-648)
The cost-effective 10-zone, 20-zone and 48-zone LED keypads connect to the bus and provide a
user-friendly display of the system's status. Includes an on-board PGM output and hardwired zone
input. This modern and stylish keypad will enhance any decor while helping you make the most of the
Digiplex security system.
ZX1 ZONEEXPANSIONBUSMODULE(DGP-ZX1)
Connected to the Digiplex communication bus, this fully supervised zone expansion module will add
1 hardwired input terminal to the Digiplex System (2 zones if ATZ is enabled).
ZX8 ZONEEXPANSIONMODULE(DGP-ZX8)
Connected to the Digiplex communication bus, this zone expansion module will add 8 hardwired
input terminals to the Digiplex System (16 zones if ATZ is enabled). Each module has one on-board
PGM output.
PGM1 EXPANSIONMODULE(DGP-PGM1)
When connected to the Digiplex communication bus, this module will add one 5A programmable
output (PGM) to the Digiplex System.
ZX4 ON-BOARD ZONEMODULE(DGP-ZX4)
Connected to the Digiplex control panel's EXPANSION input, this module will add 4 hardwired input
terminals to the Digiplex System (8 zones with ATZ enabled).

6REFERENCE& INSTALLATIONMANUAL
DIGITALBUSDETECTORS(DGP-25 & DGP-60)
Totally software-driven, digital detectors are more intelligent and more powerful than any other
detection device. This patent-pending, breakthrough technology revolutionizes the security industry
in the same way the compact disc revolutionized music and home entertainment. By connecting
directly onto the bus, you no longer have to set jumpers and complicated dip switches. Simply
program their sensitivity and other settings through any keypad in the system.
HIGH-SECURITYPIR FORDEMANDINGAREASWITHPETIMMUNITY(DGP-70)
Animal lovers can maximize their security protection thanks to the power of true digital analysis with
an intelligent patent-pending “pet-friendly” lens. There's no need to compromise performance or
detector sensitivity to deliver pet immunity.
LIBERATORTM WIRELESS BUSMODULE(DGP-319)
Connected to the Digiplex communication bus, this module will allow you to add up to 16 fully
supervised wireless zones using the LiberatorTM detectors and contact switches as well as 16
programmable remote controls. This module also includes up to two programmable 5A relays.
PRINTERMODULE(DGP-PRT1)
The Printer Module provides you with the ability to automatically print events as they occur in the
Digiplex system or the events can be stored in the module’s event buffer so you can print the events
manually. The events can be sent to a dot matrix printer or can be viewed and printed from a
computer. Includes a 50mA PGM output. Ideal for monitoring users when using the Access Control
feature.
PGM4 (DGP-PGM4)
When connected to the Digiplex communication bus, this module will provide four additional 5A
programmable outputs to the Digiplex system.
COMING SOON:
CONTACTBUSVOICEDIALERAND X-10 MODULE
ZC1 DOOR/WINDOWBUSCONTACTSWITCH

DIGIPLEX CONTROLPANEL7
3 INSTALLATION
3.1 LOCATION& MOUNTING
Before mounting the cabinet, push the five white nylon mounting
studs into the back of the cabinet. Pull all cables into the cabinet
and prepare them for connection before mounting the circuit board
into the back of the cabinet. Select an installation site that is not
easily accessible to intruders and leave at least 2" around the
panel box to permit adequate ventilation and heat dissipation. The
installation site should be dry and close to an AC source, ground
connection and telephone line connection.
3.2 EARTHGROUND
Connect the zone and dialer ground terminals from the control
panel to the cabinet and cold water pipe or grounding rod as per
local electrical codes.
For maximum lightning protection, use separate earth
grounds for the zone and dialer grounds as shown in
Figure 3-3 on page 8.
3.3 AC POWER
Use a 16.5VAC (50/60Hz) transformer with a minimum 20VA rating
to provide sufficient AC power. For increased power you can use a
transformer with a 40VA rating. For UL Listed systems, you can
use model #BE156240CAA. For CSA listed systems, use model
#BE116240AAA. Do not use any switch-controlled outlets to power
the transformer. Connect the transformer as shown in Figure 3-3
on page 8.
Do not connect the transformer or the backup battery
until all wiring is completed.
3.4 BACKUPBATTERY
In order to provide power during power loss, connect a 12VDC 4Ah
rechargeable acid/lead or gel cell backup battery (YUASA model
#NP7-12 recommended) as shown in Figure 3-3 on page 8.
Connect the backup battery after applying AC power. When
installing, verify proper polarity, as reversed connections will blow
the battery fuse. For information on how to set the Battery Charge
Current to either 350mA or 700mA, please refer to section 13.3 of
this manual
3.4.1 Battery Test
The control panel conducts a dynamic battery test under load every
64 seconds. If the battery is disconnected, if its capacity is too low
or if the battery voltage drops to 10.5 volts or less when there is no
AC, the “Battery Trouble” message will appear in the Trouble
Display. At 8.5 volts, the panel shuts down and all outputs close.
3.5 AUXILIARYPOWERTERMINALS
You can use the auxiliary power supply to power the motion
detectors, keypads and other accessories in your security system.
A fuseless circuit protects the auxiliary output against current
overload and automatically shuts down if the current exceeds 1.1A.
Auxiliary power will resume once the overload condition has
restored. For details on available output power, please refer to
Figure 3-3 on page 8. For more information on how to calculate
system consumption, refer to Calculating Power Requirements on
page9.
3.6 TELEPHONELINECONNECTION
Connect the incoming telephone company wires into the TIP and
RING connections of the control panel. Then run the wires from T1
and R1 to the telephone system as shown in Figure 3-1.
Figure 3-1: Telephone Line Connections
3.7 BELL/SIRENOUTPUT
The BELL+ and BELL- terminals power bells and/or other warning
devices that require a steady voltage output during an alarm. The
bell output supplies 12VDC upon alarm and can support two 20-
watt or two 30-watt sirens. The bell output uses a fuseless circuit
and will automatically shut down if the current exceeds 3A. If the
load on the BELL terminals returns to normal (≤3A), the control
panel will re-instate power to the BELL terminals. When connecting
sirens, please verify correct polarity as shown in Figure 3-2. Please
note that PGM5 is rated at 5A and can be used to power bells and/
or other warning devices (see Figure 3-2: Bell/Siren)by
programming it as a bell/siren output. Please refer to
Programmable Outputs in section 11.
When the bell/siren output is not used, the “Bell
Absent” message will appear in the Trouble Display.
To avoid this, connect a 1kΩΩ resistor across the bell
output.
Figure 3-2: Bell/Siren

8REFERENCE& INSTALLATIONMANUAL
Figure 3-3: Digiplex Control Panel PCB Layout