Bosch ICP-SOL2-P User manual

&RQWURO3DQHO
,&362/3,&362/3
HQ 4XLFN5HIHUHQFH*XLGH

2en | Table of Contents Control Panel
2014.06 | 02 | F01U298027 Quick Reference Guide Bosch Security Systems, Inc.
Table of contents
1Introduction 5
2Programming 6
2.1 TEXT LCD Codepad Menu Programming 6
2.2 ICON LCD Codepad Programming 9
2.3 Programming Option Bits 10
2.4 Installer's programming commands 10
3Operating Commands 11
3.1 Add/Delete RF Device (Wireless Zones) 13
3.2 Add/Delete RF Repeater 13
3.3 Add/Delete RF Keyfob 13
3.4 Set First Test Report 14
3.5 Change Domestic Telephone Numbers 14
3.6 Change the Telco Arm/Disarm Sequence 14
3.7 Set STAY Mode 2 Zones 15
3.8 Report Monitor Mode (Toggle On/Off) 15
3.9 Walk Test Mode 15
3.10 Event Memory Recall 15
4Programming Parameters 19
4.1 Phone Programming 19
4.1.1 Receiver 1 19
4.1.2 Receiver 2 19
4.1.3 Dialing Format 20
4.1.4 External Network Module 1 20
4.1.5 External Network Module 2 20
4.1.6 Password for A-Link Plus/RSC Connection 20
4.1.7 Telco Arming Sequence (Call Forward On) 20
4.1.8 Telco Disarm Sequence (Call Forward Off) 20
4.1.9 Call Back Telephone Number 20
4.1.10 Ring Count 21
4.1.11 Telephone Line Fail Options 21
4.1.12 Dialer Options 1 21
4.1.13 Dialer Options 2 21
4.1.14 Dialer Options 3 22
4.1.15 A-Link Plus Options 22
4.2 Installer Code 22
4.3 User Code Programming 22
4.4 Day Alarm Zones 24
4.5 EOL Resistor Value 24
4.6 Zone Programming 24
4.7 Swinger Programming 27
4.7.1 Swinger Shutdown Count For Siren 27
4.7.2 Swinger Shutdown Count For Dialer 28
4.8 Zone Status Programming 28
4.8.1 STAY Mode 2 Automatically Bypass Zones 28
4.8.2 Reserved 28
4.8.3 Zone Status Reporting Options 28
4.9 RF Programming 29
3.11 Fault Analysis Mode 16

Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. Quick Reference Guide 2014.06 | 02 | F01U298027
4.9.1 RF Supervision Time 29
4.9.2 RADION Anti-Jamming Sensitivity 29
4.9.3 RF Receiver 29
4.9.4 RF Options 29
4.9.5 Reserved 29
4.10 Report Programming 29
4.10.1 Reserved 29
4.10.2 Arm / Disarm Reporting Options 30
4.10.3 Reserved 30
4.10.4 Codepad Reporting Options 30
4.11 System Status Programming 30
4.11.1 Reserved 30
4.11.2 Access Denied(Code Retry) 30
4.11.3 System Status Reporting Options 30
4.12 Test Report Programming 31
4.12.1 Test Report Time (Automatic) 31
4.12.2 Test Reporting Dialer Options 31
4.13 Output Programming 31
4.14 Time Programming 35
4.14.1 Entry Time 1 35
4.14.2 Entry Time 2 35
4.14.3 Exit Time (AWAY/STAY Modes) 35
4.14.4 Entry Guard Time For STAY Mode 35
4.14.5 Delay Alarm Report Time 35
4.14.6 Sensor Watch Time 35
4.14.7 Codepad Lockout Time 35
4.14.8 Siren Run Time 36
4.14.9 Siren Sound Rate 36
4.14.10 Auto Arming Pre-Alert Time 36
4.14.11 Auto Arming Time 36
4.14.12 Auto Disarming Time 36
4.14.13 Kiss-Off Wait Time 36
4.14.14 Speaker Beep Volume 37
4.15 Options Programming 37
4.15.1 System Options 1 37
4.15.2 System Options 2 37
4.15.3 System Options 3 37
4.15.4 System Options 4 37
4.15.5 Consumer Options 1 38
4.15.6 Consumer Options 2 38
4.15.7 Consumer Options 3 38
4.15.8 Reserved 38
4.15.9 Partitioning Options 1 35
4.15.10 Partitioning Options 2 39
4.16 Partition Allocations 39
4.16.1 Zone Area Assignment 39
4.16.2 Codepad Assignment 39
4.16.3 Reserved 39
4.16.4 User Code Area Assignment 40
4.17 Default Options 40

4en | Table of Contents Control Panel
2014.06 | 02 | F01U298027 Quick Reference Guide Bosch Security Systems, Inc.
4.18 IP Destination 40
4.19 RF User Code ID Numbers 42
4.20 RF Zone/Device ID Numbers and RF Zone Option 42
4.21 RF Repeater ID Numbers 43
4.22 Text Codepad Items 43
4.22.1 Home Message 43
4.22.2 Zone Names 43
4.22.3 User Names 44
4.22.4 Area Names 44
5Appendices 45
5.1 Connections for EOL Resistors 45
5.2 Wiring Diagram 46
5.3 Component Overlay 47

Control Panel Introduction | en 5
Bosch Security Systems, Inc. Quick Reference Guide 2014.06 | 02 | F01U298027
Introduction
Thank you for choosing the ICP-SOL2-P/ICP-SOL3-P Control Panel for your installation. You
will find this system extremely flexible, reliable, and easy to use. This Quick Reference Guide
is supplied with the system to provide users with enough basic information to wire, configure,
and program the system. Due to the systems many programmable features and options, we
suggest that you obtain the ICP-SOL2-P/ICP-SOL3-P Installation Guide that provides detailed
information on system options, functions, and programming methods.
Throughout this document, the words “control panel ” refer to all control panels covered by
this document (ICP-SOL2-P/ICP-SOL3-P).
Features ICP-SOL2-P ICP-SOL3-P
Number of users or RF keyfobs 32 32
Number of WE800EV2 keyfobs HCT-4 21 21
Number of RADION keyfobs RFKF-TB or RFKF-FB 0 32
Number of areas 2 2
Number of zones 4 (Onboard) + 4
(zone doubling)
8 (Onboard) + 8
(zone doubling)
Number of Onboard outputs 4 4
Number of text LCD codepads IUI-SOL-TEXT or
ICON LCD codepads IUI-SOL-ICON
44
Number of wireless receiver WE800EV2 1 1
Number of RADION receiver B810 0 1
Number of RADION repeater RFRP 0 8
Number of B308 Octo-output Modules 1 1
Number of B426 Conettix Ethernet
Communication Modules
22
Number of B450 Conettix Plug-in Communicator
Interfaces
22
Table 1.1: Control Panel Capacities
1

6en | Programming Control Panel
2014.06 | 02 | F01U298027 Quick Reference Guide Bosch Security Systems, Inc.
Programming
The programming options of the system are stored in a non-volatile EPROM. This memory
holds all information during a total power loss and can be changed as many times as required.
The entire programming sequence consists of entering a location number and changing the
data as required.
Use the following methods to program the system:
– Codepad
– A-Link Plus Software
2
2.1 TEXT LCD Codepad Menu Programming
1. Enable Text codepad and confirm that the system is in disarmed status.
2. To enter Installer’s Programming Menu, enter the installer code (Default = 1234) followed
by the [#] key or [-] key.
3. Programming: Select the menu and operate according to the menu prompt.
– Down to the next menu: Press [Ⴍ]
– Up to the previous menu: Press [Ⴃ]
– Enter menu or confirm input : [#]
– Back to the menu or exit programming item setting: Press [-]; or press and hold [-]
for 3 seconds to exit programming without saving changes.
– Operate according to the menu prompt. Select menu and enter or select data for
specific programming items to complete programming, step by step. For specific
items and options, refer to Programming Parameters, page 15.
4. After completing input, press [-] to get back to the previous menu. Complete all
programming input by repeating step 3 and press [-] to get back to the current main
menu level by level.
5. To use the TEXT LCD codepad in location programming mode (like IUI-SOL-ICON), enter
programming option [8] [1].
6. When [Confirm to Save Parameter Changes?] display, press [#] to save parameter
changes , exit menu programming and reset system.
– In location programming mode enter the programming location then [#].
– Enter the new data then [*] to save it. Enter [#] to go to the next location.

Control Panel Programming | en 7
Bosch Security Systems, Inc. Quick Reference Guide 2014.06 | 02 | F01U298027
TEXT LCD Codepad Programming Tree
.
Command
Installer
Passcode
Inquire
System
RF diagnose
Test
12
3
4
5
Fault analysis1Event recall
2
Day alarm
2Arm/disarm seq.
3Report monitor
4Modem call init.
5Domestic phone
6Version display
7Factory default
8
RF zone1RF Keyfob
2RF Repeater
3
Horn speaker1Bell test
2Strobe test
3Walk test
4Test report
5
Access
2
Installer code
Access retry
1
3User allocate2User authority
3
User property
4
System
Timer
Codepad
Arm/disarm
Fault
Wireless
System option
31
2
3
4
5
6
Entry time11Entry time2
2Exit time
3Entry guard time for STAY mode
4Sensor watch time
5Codepad lockout time
6Auto arm pre-alert time
7Auto arm time
8Auto disarm time
9
Silent codepad panic alarm1Silent codepad fire alarm
2Silent codepad medical alarm
3Codepad access denied silent
4Codepad fault beep enable
5Codepad display off after 60s
6
Auto arm in STAY11Single button arm enable
2Single button disarm enable
3Disarmed on power up
4Arm/disarm track on power up
5Phone remote arm
6Answer machine bypass on arm
7
Ignore AC fail1AC fail report wait time
2Horn speaker fault monitor
3Phone line fault indicator
4Phone line fault alarm on armed
5Phone line fault alarm on disarm
6Lockout phone line fail alarm
7
RF receiver1Zone RFID and input option
2Keyfob RFID
3Repeater RFID
4RF supervision time
5RF jam sensitivity
6RF RECE jam/tamper siren alarm
7RFKF button4 arm in STAY1
8RF arm/disarm strobe indicator
9
Home message1Button factory default enable
2Alarm memory reset on disarm
3STAY indicator for day alarm
4Digit 3 for codepad duress alarm
5Siren and strobe output in STAY
6Speaker beep volume
7
[181]
[424]
[189]
[534]
[466]
[468]
[470]
[472]
[476]
[478]
[481]
[482]
[486]
[493.1]
[493.2]
[493.3]
[493.4]
[498.1]
[497.1]
[496.3]
[497.2]
[497.3]
[495.1]
[495.2]
[177.2]
[177.3]
[494.2]
[494.1]
[492.2]
[176.1]
[176.2]
[176.3]
[179.2]
[395]
[1820]
[1500]
[1980]
[393]
[394]
[396.2]
[492.4]
[492.3]
[2500]
[900]
[497.4]
[496.4]
[498.2]
[498.3]
[491]

Bosch Security Systems, Inc. Quick Reference Guide 2014.06 | 02 | F01U298027
8en | Programming Control Panel
Zone
Zone config
Installer
Passcode
Zone allocate
Zone name
Day alarm zone
STAY2 zone
EOL resistor
Zone state report
41
2
3
4
5
6
7Siren swing shutdown count1Report swing shutdown count
2
Telco arming sequence
1Telco disarming sequence
2Delay alarm report time
3Kiss-off wait time
4Delay siren until transmit over
5Extend wait for handshake
6Upload/download enable
7Callback phone number request
8Callback phone number
9
Siren run time
1Siren sound rate
2Siren sound on RF receiver fail
3
Silent zone tamper alarm1Unseal RF zone that failed monitor
2Bosch Smart Lockout enable
3Zone pulse count handover enable
4Handover delay in order
5
Area
5Codepad area
Area option
1
2
Output
6
STAY mode arm/disarm rpt enable1Arm/disarm rpt only if alarmed
2First disarm/last arm report
3Arm/disarm report option
4Codepad report option
5Test report time and interval
6Test report only when armed
7Test report on siren reset
8Test report option
9
First phone number1Second phone number
2Transmit format
3Subscriber ID number
4IP destination
5CSVIP user name and password
6
Ring count1Report function enable
2Exit A-Link connection on alarm
3System status report option
4Use bell-103 for FSK format
5DTMF dial pulse to 1 digit/sec
6Set up domestic dialing format
7
Swing shutdown
8
Zone option
9
Arm/disarm all areas once1Reset siren from any area
2
Onboard output
Codepad output
Extend output
Siren config
1
2
3
4
Comm
7Receiver config
Network config
Report config
Comm option 1
Comm option 2
1
2
3
4
5
Network module1A-Link/RSC password
2
Parameter
8Address program
Address auto step
Adapter
1
2
3Test adapter
1Read adapter
2Write adapter
3
[267]
[502]
[2536]
[265]
[381]
[266]
[392] [379]
[380]
[498.4]
[396.3]
[492.1]
[494.3]
[494.4]
[501.2]
[500.3]
[518]
[436]
[460]
[646]
[177.4]
[0, 40]
[16, 56]
[33, 73]
[34, 74]
[1000, 12000]
[1100, 1300]
[479]
[480]
[396.1]
[81]
[83]
[175]
[177.1]
[180.3]
[427]
[178.2]
[178.1]
[500.1]
[403]
[411]
[428, 434]
[496.1]
[496.2]
[435]
[179.1]
[*]
[474]
[490]
[178.3]
[178.4]
[180.1]
[180.2]
[159]
[113]
[143]

ICON LCD Codepad Programming
The system must be disarmed (with no active alarm) to program the system. If there is an
active alarm or the system is armed, enter the code for User 1 (Default = 2580) followed by
the [#] key. (User Code 1 is factory default as the Master Code.)
1. Enter Installer’s Programming Mode: Enter the installer code (Default = 1234) followed by
the [#] key. Two beeps are heard and both the STAY and AWAY indicators flash
simultaneously to indicate that you entered programming mode. The codepad indicators
display the current data programmed in Location 0000 (first location of the Primary
Telephone Number).
2. Programming: Move to the required location and program new data into location.
– To move to another programming location, enter the location number followed by
the [#] key. The data in the new location is displayed using the codepad indicators.
(For example, if you enter [34 #], the system jumps to Location 0034, the beginning
of the Subscriber ID Number For Receiver 1.)
– To move to the next location, press the [#] key. This steps you to the next location.
The data in the next location is displayed using the codepad indicators. (For
example, if you are currently positioned at Location 0034, pressing [#] key takes you
to Location 0035.)
– To step back one location, press the [*] key. (For example, if you are currently
positioned at Location 0035, pressing the [*] key returns to Location 0034.)
– To change data in the current location, enter the new value (0 to 15) followed by the
[*] key. This stores the new data into the location. (For example, if you enter the
value [14*], the Zone 14 indicator display to represent the new data value.)
3. Exit from Installer’s Programming Mode: Enter [960#]. Two beeps are heard and the STAY
and AWAY indicators no longer display. The system returns to the disarmed state and is
ready for use.
Task Keystrokes
Enter Installer’s Programming Mode [1234#]
Exit from Installer’s Programming Mode
without saving changes
[958#]
Exit from Installer’s Programming Mode with
saving changes and panel reset
[960#]
Step to next Location [#]
Step back one Location [*]
2.2
Program new data into Location [Data][*] (Data = 0 to 15)
Jump to another Location [Location No.] [#]
2014.06 | 02 | F01U298027 Quick Reference Guide Bosch Security Systems, Inc.
Control Panel Programming | en 9

Bosch Security Systems, Inc. Quick Reference Guide 2014.06 | 02 | F01U298027
10 en | Operating Commands Control Panel
Programming Option Bits
Use option bits to program any combination of the four different options in one location by
adding the options together. Programming a zero disables all four options.
Example
If at Location 0177 you only want options 1, 2, and 4, add the numbers together and the total
is the number to be programmed. The number to be programmed is 7 (1 + 2 + 4 = 7).
Option Description
1 Dialer reporting functions allowed
2 Remote arming using Telephone allowed
4 Answering machine bypass only when armed
8 Use bell 103 for FSK format (Disabled = CCITT V21)
Table 2.3: Programming Option Bits
Installer's programming commands
Installer Programming Commands, displayed in below table can only be used when you enter
Installer’s Programming Mode. Enter the command followed by the [#] key.
Command Description
958 Exit from Installer’s Programming Mode without saving changes
959 Test IUI-SOL-ADAPTER
960 Exit from Installer’s Programming Mode with saving changes and panel
reset
961 Reset the control panel to factory defaults
962 Copy the control panel memory to IUI-SOL-ADAPTER
963 Copy IUI-SOL-ADAPTER data to the control panel memory
965 Set up domestic dialing format
966 Enable/disable the automatic stepping of locations during programming
999 Display the software version number or control panel type
Table 2.4: Installer’s Programming Commands
2.3
2.4