Ayyeka WAVELET - V2 User manual

Jan 2020
P/N0100706
WAVELET –V2
WA1111-xx-V2
QUICKSTART
GUIDE

3
2
It is important that you read the Quick Start Guide
in acontrolled environment prior to installation.
Set up, activate, and successfully test the entire
system (Wavelet-V2, sensors, and antenna
connection) indoors, in acontrolled environment,
before going to the field for installation.
!

IMPORTANT
Contact the Ayyeka Support Team for technical assistance:
[e-mail]
[phone] (US)
[phone] (EMEA)
[phone] (IL)
Always coordinate the installation with the local authority
before starting installation. Installation should be completed
by trained and authorized personnel. If assistance from
Ayyeka Support is needed, schedule a request in advance,
and make sure that you get confirmation before the
installation.
The Ayyeka Limited Warranty covers only Ayyeka-supplied
hardware and software for the duration of the warranty
period as per the warranty terms and conditions.
Do not throw away the device because it contains a lithium
battery. Dispose of the battery properly according to local
laws and regulations.
Operating temperature range: -40°C to -80°C (-40°F to -176°F)
4G (LTE)/3G/2G cellular network signal is required for proper
communication.
Ayyeka is not liable for damage or injury as a result of
handling, installation, or maintenance of its supplied
systems.
3

Analog port
7.3cm
(2.8 in)
17.4 cm
(6.9in.)
IP 68/ NEMA 6P Wavelet
mechanical enclosure
Slots for zip ties and/or bolts
for mounting
Panel connectors protector
13.3 cm
(5.2 in.)
Magnetic Activator
FRONT
BOTTOM
External power port
Serial port
Discrete port
Cellular antenna port
SCHEMATIC
4
LoRaWAN
antenna port
(for LoRaWAN-
enabled devices)

INTERNAL
UPPER ENCLOSURE
INTERNAL
LOWER ENCLOSURE
Military-grade lithium battery pack
(field replaceable, non-rechargeable)
Interface board ON/OFF switch
Indicator LEDs
GSM antenna
SIM card slot #2
Memory card
GPS antenna
SIM card slot #1
Cellular modem
5
SCHEMATIC

1
3
Wavelet Device
M12 field attachable
sensor connectors
(optional; ordered separately)
Wavelet Activator
1x
1x
1x
M8 female field attachable
power connector
(optional; ordered separately)
1x
1x 1x
1x
Panel connectors protector
6
COMPONENTS

1
3
Cellular antenna and
mounting bracket
(REQUIRED and sold separately)
4x2x 4x
Zip ties, screws, and anchors
7
COMPONENTS

SENSOR CONNECTION
Connect the sensor cable(s) assembly with the field attachable
connector to the mating panel connector on the Wavelet. See pages
20-24 for more details.Turn the adjustable stainless-steel end piece to
secure the field attachable connector to the Wavelet.
!CAUTION: Do not turn the black plastic hood of the
connector. Turning the black hood may cause the wires to
disconnect, break, and/or damage the connector pins.
TURN HERE
DO NOT
TURNHERE
8

EXTERNAL ANTENNA CONNECTION
Connect the Cellular antenna to the antenna port (ANT1).
The antenna does not appear in the remaining
depictions in this guide, but it must remain connected
after it is properly secured to the appropriate panel
connectors.
Cellular antenna
(required)
Place the magnetic Wavelet Activator on the embossed Wavelet logo on
the front of the Wavelet enclosure.
The Wavelet will initiate a 15-minute test mode of sampling and send a
few transmissions of data. The device will then return to its default
configuration.
9
Wavelet Activator

10
WAVELET POTECTOR
After connecting sensors and antenna, place the Wavelet protector
above the connector ports and secure the Wavelet protector into the
Wavelet enclosure.
Lower Clips
Upper Clips
Protector
Arches
a. Insert the two lower clips into the two lower holes of the Wavelet
enclosure.
b. Snap the upper clips into place in the two grooves above the panel
connector.
a
b
CAUTION: The protector is provided to shield the
connector from tampering or over-exposure that could
result in disconnected wiring.
If you need to remove the protector, grasp it at the
protector arches and pull up. The protector will snap off.