Digital Watchdog DWC-D3661T User manual

07212014
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Starlight MPA
Indoor Dome Camera
DWC-D3661T
DWC-D3661TIR

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damage.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth wi h a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residen ial environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Easy Installation
Connecting to Monitors
Control Board
4
5
6
7
8
9
10
13-25
26
27-28
29-30
Adjus ing the Camera Gimbal 12
Adjus ing the Camera Lens 11

4
FEATURES*
1/3" Sony 1.3M CMOS
820 TV Lines [B/W], 800 TV Lines [Color]
2.8~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync, Smart IR [DWC-D3661TIR]
True Day & Night with IR Cut Filter
3D DNR (3D Digital Noise Reduction)
WDR (Wide Dynamic Range)
Star-Light (Super Low Light Technology)
HME (Highlight Masking Exposure)
Defog (Extreme Weather Image Copmensation)
Digital Quick Zoom & 8x Digital Zoom
16:9 and 4:3 Viewing Modes
AGC / BLC / AWB
Privacy Zones (16) & Motion Detec ion
Camera Control via RS-485/ UTC
RS485, UTP, & 1Alarm Output Built-In
Secondary BNC Output

PARTS & DESCRIPTION*
5
6
7
9
8
1Bottom Case
Camera Gimbal
Upper Case
Dome Cover
BNC Cable
DC12V Cable
UTP Cable
RS485 Cable
Alarm Output Cable
2
3
4
5
1
2
3
4
65
8
7
9

DIMENSIONS IN MILLIMETERS (IN)*
120.0 4.72”
9.0 0.3539.0 1.53”
89.4 3.52”
81.0 3.19”
89.0 3.50”
6

Included with your Camera
1
2
5
4
3
User Manual
Moun ing Template
2 Machine Screws and 2 Dry Wall Anchors
Secondary Video-BNC Cable
Power Cable
0 0
AB U MA UA
B
B
Strl ght MPA
Indoor Dome Camera
DWC-D366
DWC-D366 R
7
INSIDE THE BOX*

EASY INSTALLATION*
1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.
2. Use he camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.
5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.
6. Use he joystick to adjust the OSD menu. See pages
13-21 for more information.
7. Snap the camera’s cover dome to the camera base to complete
the installation.
8

Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
Monitor
CCTV Monitor
Second Video Output
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
CONNECTING TO MONITORS*
Right
Left
Up
Down
9

Joystick: Controls the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
CONTROL BOARD*
Remove he camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control he camera’s OSD options.
1
2
10