Digital Watchdog Power PIX DWC-D3361WTIR User manual

12132013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Indoor Dome IR Camera
DWC-D3361WTIR
All manuals and user guides at all-guides.com
all-guides.com

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules.These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
All manuals and user guides at all-guides.com

Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Mount Installation Instructions
Connecting to Monitors
Control Board
Adjusting the Camera Lens
4
5
6
7
8
9
10
11
13-21
22
23-24
25-26
Adjusting the Camera Angle 12
All manuals and user guides at all-guides.com

4
FEATURES*
1/3” 760H CMOS Sensor Chip (760 Horizontal Pixels)
690TVL
2.8~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
TDN (True Day & Night) with IR Cut Filter
WDR (Wide Dynamic Range)
2D DNR (2D Digital Noise Reduction)
Smear Cancelation
AGC / AWB
Easy Icon Driven OSD Menu with Built-in Joystick
Auto Sensing 24VAC/12VDC
All manuals and user guides at all-guides.com

5
PARTS & DESCRIPTION*
1Bottom Case
Camera Gimbal
Upper Case
Dome Cover
2
3
4
1
2
3
4
All manuals and user guides at all-guides.com

6
DIMENSIONS IN MILLIMETERS (IN)*
120.0 4.72”
9.0 0.3539.0 1.53”
89.4 3.52”
81.0 3.19”
89.0 3.50”
All manuals and user guides at all-guides.com
all-guides.com

7
INSIDE THE BOX*
Included with your Camera
1
2
3
5
4
User Manual
Mounting Template
4 Machine Screws and 4 Dry Wall Anchors
L-Key
Secondary Video-BNC Cable
08122013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Indoor Dome IR Camera
DWC-D3361WTIR
All manuals and user guides at all-guides.com

8
EASY INSTALLATION*
1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.
2. Use the camsera or mounting template to mark and drill the
necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.
5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.
6. Use the joystick to adjust the OSD menu. See pages
13-21 for more information.
7. Snap the camera’s cover dome to the camera base to complete
the installation.
All manuals and user guides at all-guides.com

Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
Monitor
CCTV Monitor
Second Video Output
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
9
CONNECTING TO MONITORS*
Right
Left
Up
Down
All manuals and user guides at all-guides.com

10
Joystick: Controls the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
CONTROL BOARD*
Remotve the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.
1
2
All manuals and user guides at all-guides.com