Digital Watchdog STAR-LIGHT AHD DWC-D3763WTIR User manual

ABOUT MANUAL
Indoor Dome Camera
Analog High Definition
DWC-D3763WTIR
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
01/2016
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
2
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Table of Contents
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
4
5
6
Inside the Box
Easy Installation
Connecting to Monitors
Control Board
Adjusting the Camera Angle
9
7
8
10
11
12-25
26
27-28
29-30
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
3

FEATURES*
Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
Panasonic 1/3" CMOS Sensor
1080P Resolution at 30fps
Digital Wide Dynamic Range (DWDR)
Varifocal P-Iris Lens 2.8~12mm
Smart IR™ with Intelligent Camera Sync. 100ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
Secondary Video-BNC Output (While UTP in use)
Easy Icon Driven OSD Menu with Built-in Joystick
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
4

PARTS & DESCRIPTION*
1
5
6
7
2
3
4
Bottom Case
Camera Gimbal
Upper Case
Dome Cover
UTP Cables
RS485 Cables
Alarm Output Cable
3
4
1
2
5
6 7
Set Screw
5
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

DIMENSIONS IN MILLIMETERS (IN)*
89.0 3.50”
81.0
120.0 4.72”
9.0 0.3539.0 1.53”
89.4 3.52”
3.19”
6
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

INSIDE THE BOX*
Included with your Camera:
1
2
5
4
3
User Manual
Mounting Template
2 Machine Screws and 2 Dry Wall Anchors
Secondary Video-BNC Cable
Power Cable
10222013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Strlight MPA
Indoor Dome Camera
DWC-D3661T
DWC-D3661TIR
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
7

EASY INSTALLATION*
1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.
2. Use the camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.
5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.
6. Use the joystick to adjust the OSD menu. See pages
13-21 for more information.
7. Snap the camera’s cover dome to the camera base to complete
the installation.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
8

CONNECTING TO MONITORS*
Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
CCTV Monitor
Monitor 300.0
Right
Left
Up
UTP
2ND
COAX
Down
2nd Video Output
Power Connection -12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
NOTE: Make sure the UTP/ COAX switch is set to the proper connection. If the switch is set, for
example to UTP, but the camera is connected via Coax, the video from the camera will appear black.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
9

CONTROL BOARD*
Joystick: Controls
the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
1
2 Remove the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
10