Digital Watchdog DWC-PB6M4T User manual

Quick Start Guide
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
DWC-PB6M4T
Default Login Information
Username: admin Password: admin
WHAT’S IN THE BOX
Quick
setup
guide
1Sunshield
screws 1 Set
Mounting
template 1
Screws and
plastic
anchors – 4pcs
1 Set
Sunshield 1T-Wrench 1
1. Once all cables are connected, secure the camera to the mounting surface using the included screws.
2. To adjust the camera’s pan and tilt, loosen the pan/tilt stopper screw. Adjust the camera’s position as needed.
You may use the camera’s video test cable for local image view.
3. Attach the sunshield to the camera by using the provided sunshield screws.
1. The mounting surface must bear five times the weight of your
camera (2.2 lbs).
2. Mind the cables and power line to avoid damage.
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power
Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc,
880 mA min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with
the output evaluated as a Limited Power Source as defined in
UL60950-1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
7. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
Pass the wires through the mount bracket and make all
necessary connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch,
connect the camera using an Ethernet cable for both data
and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE
switch, connect the camera to the switch using an Ethernet
cable for data transmission and use a power adapter to power
the camera.
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power requirements Power consumption
DC12V, PoE IEEE 802.3at
Class 3
(adapter not included)
TDN On: MAX 10.1W
TDN O: 7.7W
STEP 3 – INSTALLING THE CAMERA
AUDIO
INPUT
AUDIO
OUTPUT
POWER
NET WORK
ALARM
OUTPUT
ALARM
INPUT
IR
ILLUMINATOR
Reset
Button
SD Card Slot
Test Video Output

Rev Date: 04/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Quick Start Guide
STEP 6 – DW IP FINDER™
Network Setup
1. To install the DW IP Finder™, go to:
http://www.digital-watchdog.com
2. Enter “DW IP Finder” on the search box at the top of the page
and press Enter.
3. Click on the DW IP Finder from the search result and go to
Software tab. Click on download icon to download the DW IP
Finder installation file.
4. Run the installation file and follow the wizard to install the DW
IP Finder™. Open the DW IP Finder™ and click ‘Scan Devices’. It
will scan the selected network for all supported devices and list
the results in the table. During the scan, the DW logo will
turn gray.
Default ID / PW : admin / admin
‘Port forwarding’ has to be set in your
network’s router for external access
to the camera.
*NOTE: For security purposes, it is highly
recommended to change your
password after initial setup.
Default TCP/IP information: DHCP
Select DHCP if the internet service is dynamic IP. This will allow the
camera to receive its IP address from the DHCP server.
Select “Static” to manually enter the camera’s IP address, (Sub)
Netmask, Gateway and DNS information.
* The camera’s IP must be set to Static if connecting to
DW Spectrum
Contact your network administrator for more information.
Thumbnail view
Firmware version
Camera’s uptime
Open Device
configuration
settings
Filter device type to scan
Scan devices
Select network to scan
Show/hide thumbnail view
Refresh thumbnail view
Bulk IP assignment
Firmware upgrade
Device’s
information
5. Select a camera from the list by double-clicking on the
camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.
6. To access the camera’s web page, click on ‘View
Camera Website’.
7. To save the changes made to the
camera’s setting, input username and
password of the camera and click Apply.
Click “Scan Devices” from the
main screen again to display the
updated information.
Use the DW IP Finder™ software to scan the network and detect all MEGApix®cameras, set the camera’s network settings or access the camera’s web client.
STEP 7 – WEB VIEWER
STEP 4 – MANAGING THE SD CARD
STEP 5 – RESETTING THE CAMERA
To install the memory card (not included):
1. To install the camera’s SD Card, locate the SD card slot in the side
of the camera by unscrewing
the con cap.
2. Insert class 10 SD/SDHC/SDXC card into the SD card slot by
pressing the SD card until clicks.
3. To remove the SD card, press the card inward until it clicks to
release from the card slot then pull out from the slot
To reset the camera, use the tip of a paper clip or a pencil and press
the reset button. Pressing the button for five (5) seconds will initiate a
camera-wide reset of all the settings, including network settings.
Con Cap SD Card Slot
1
2
3
Reset Button
Once the camera’s network settings have been setup properly, you
can access the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will
open up in your default web browser.
4. Enter the camera’s username and password
(default are admin / admin).
5. If you are accessing the camera for the first time, install the
ActiveX files in order to view video from the camera.
The GUI display may dier by camera models.
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
NOTE: Some Menu options may not be available based on the
camera model. See the full manual for more information.
*