Digitus Biometrics CodeLock User manual

db CodeLock
Installation Manual
Version 1.0

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 2 of 10
Table of Contents
Determining which Lock Pawl to use .................................................................................................. 3
Overview ................................................................................................................................... 4
Securing the Door Lock - Step 1 ....................................................................................................... 4
Mount the tie-down pads to the Door and Cabinet – Step ..................................................................... 5
Route the Cable between the lock and the Remote Node / db Sentry Controller or ACM Panel – Step 3 ................. 6
Connect the cable to the Remote Node / db Sentry Controller – Step 4 ........................................................ 7
Connect the lock to 3
rd
-party Access Panel .......................................................................................... 8
Connect the SENSE OUT to monitor the lock position (open/closed) ........................................................... 9

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 3 of 10
Determining which Lock Pawl to use
As all cabinets vary, we offer a wide range to pawls to suit the particular dimensions of your cabinet.
If new pawls are required, there is a simple measurement that needs to be taken to determine which pawl you will
need. Using the existing mechanical lock, measure the length of “H” in millimeters (mm) as shown in figure 1. Using
“H” determine which pawl is required from Table 1.
Once the correct pawl model has been determine, please contact our lock support team at [phone]
Figure 1
Standard Pawl
Pawl with Rod Control
H (mm)
Model #
H (mm)
Model #
4
1000
-
11
4
1000
-
U63
6
1000
-
6
1000
-
U 1
8
1000
-
113
8
1000
-
U64
10
1000
-
1
10
1000
-
U
13
1000
-
0
13
1000
-
U 3
14
1000
-
19
14
1000
-
U 4
16
1000
-
18
16
1000
-
U 5
18
1000
-
17
18
1000
-
U 6
0
1000
-
16
0
1000
-
U 7
1000
-
15
1000
-
U 8
4
1000
-
14
4
1000
-
U 9
5
1000
-
7
5
1000
-
U30
6
1000
-
50
6
1000
-
U31
8
1000
-
13
8
1000
-
U3
30
1000
-
8
30
1000
-
U33
3
1000
-
6
3
1000
-
U34
34
1000
-
1
34
1000
-
U35
35
1000
-
1
1
35
1000
-
U36
36
1000
-
51
36
1000
-
U37
38
1000
-
5
38
1000
-
U38
40
1000
-
5
40
1000
-
U39
4
1000
-
53
4
1000
-
U40
44
1000
-
54
44
1000
-
U41
45
1000
-
10
45
1000
-
U4
47
1000
-
55
47
1000
-
U43
50
1000
-
56
50
1000
-
U44
Table 1
In most situations the pawl f
rom the existing mechanical handle can be re
-
used with the new lock.

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 4 of 10
Overview
If you are installing the lock into to a cabinet that already has a lock installed, remove the existing lock at this time.
Securing the Door Lock - Step 1
 Secure the lock to the door using the top mounting bracket and bottom mounting bracket as show in Figure 1. Do
not over-tighten the screws in the bottom mounting bracket as this may jam the lock mechanism.
Page 3 of this document describes how to determine which pawl you will need, depending on the make and model
of cabinet.
Pay particular attention to the rotation limiter. This is installed as shown depending on whether you have a right on
left hand opening door.
Pawl
Rotation Limiter
Figure 1
Note.
Do not use an electric screwdriver to tighten the screws.

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 5 of 10
Mount the tie-down pads to the Door and Cabinet – Step 2
The ties down pads are used to secure the supplied cable that connects the lock directly to the Remote Node / db
Sentry or ACM panel.
Ensure that the door surface is clean and free from any debris. (Using neat alcohol to clean the surface is highly
recommended. Allow drying time before proceeding.)
Figure
Remove the protective cover from each tie-down pad and situate as shown in Figure .

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 6 of 10
Route the Cable between the lock and the Re ote Node / db Sentry Controller or ACM Panel –
Step 3
Route the lock cable to the door hinge as shown in Figure 3. Secure the cable to the tie-down pads using the
supplied cable-ties. Connect the supplied device cable to the RJ-45 coupler and route it to the Remote Node or
Sentry, if using Digitus a controller. If connecting to a third party access control panel, connect a network cable to RJ-
45 coupler and run back to panel.
Figure 3

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 7 of 10
Connect the cable to the Re ote Node / db Sentry Controller – Step 4
Locks are connected to the Remote Node or db Sentry’s socket circled in the diagram below.
Each Remote Node / db Sentry Controller has two device inputs, Dev 1 and Dev .
Side View of Remote Node
Side View of db Sentry
It is recommended that for a cabinet with doors, the front door is connected to Dev 1 and the back door is connected to
Dev .

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 8 of 10
Connect the lock to 3
rd
-party Access Panel
Orange/White – GND, Ground
Orange – LOCK CTRL. Requires a 1 V ( 4V if a 4V version of the db CodeLock was purchased) control line to unlock the
handle
Green/White – RED LED. Connect to the Red LED output on the 3
rd
-party panel
Blue – V+, Requires a 1 VDC Supply
Blue/White – LATCH POS (used to indicate if the lock is open or closed) – Will be pulled to Ground (GND) if the handle is
closed. Will be open circuit if the handle is open. See diagram below
Green – GREEN LED. Connect to the Green LED output on the 3
rd
-party panel
Brown/White – Wiegand DATA 1
Brown – Wiegand DATA 0

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 9 of 10
Connect the SENSE OUT to onitor the lock position (open/closed)
If the 3
rd
-party Access Panel requires a -wire input to monitor the door positions, an external relay is required.
Connect as follows:
Black
Wire
3rd-party Access Panel
C
NO NC
+V0V
External
Relay
+V 0V
SENSE OUT. Connect to
Blue/White Wire from ock.
DOOR
SWITCH
INPUT
Yellow
Wire
Blue
Wire
Red
Wire

db CodeLock Version 1.3 Digitus Biometrics, Inc. 2017
Page 10 of 10
Digitus Biometrics, Inc.
2 East Bryan Street, Suite 502
Savannah, A 31401 USA
Phone: [phone]
Fax: [phone]
www.digitus-biometrics.com
[email protected]
Specifications subject to change without notice.