DIODE LED DI-DMX-WIFI-WMUS-3Z-WH User manual

DRY LOCATION
1 OF 5 IG050919-4.0
DMX ZONE CONTROLLER INSTALLATION GUIDE
®
COLOR-CHANGING
INSTALLATION GUIDE
DMX WALL MOUNT ZONE CONTROLLER
24VDC
12VDC
COMPATIBLE
DMX
SAFETY & WARNINGS
QUICK SPECS / MODELS
TOOLS FOR INSTALL
Phillips-head screwdriver
INSTALLATION
DI-DMX-WIFI-WMUS-3Z-WH
Input Voltage 12 - 24VDC Constant Voltage
Output Signal DMX512
WiFi Transming
Distance 40 .
®
1 2
3
Flat-head screwdriver
Mini at-head screwdriver Wire stripper
1
TURN POWER OFF AT CIRCUIT BREAKER
SHOCK HAZARD! May result in serious injury or death.
Turn power OFF at circuit breaker prior to installaon.
2
DETERMINE LOCATION TO INSTALL COMPONENTS
®
1 2 3
V+
V-
V+
CH1 - R
CH2 - G
CH3 - B
CH4 - W
0-5 0-9 0-9
Data IN
Data OUT
LED Driver(s) Controller DMX Decoder Luminaire
See SYSTEM DIAGRAM for more informaon. DMX luminaires can be
connected directly to controller. DMX Decoders are only ulized to
control Non-DMX type luminaires.
3
If system remains unresponsive or is working improperly, turn OFF main
power at breaker and verify all connecons.
4
CONNECT COMPONENTS
Only use copper wiring. Reference WIRING CONNECTIONS and SYSTEM
DIAGRAM further in this guide for visuals.
TURN POWER ON AT CIRCUIT BREAKER
1. Install in accordance with naonal and local electrical code
regulaons.
2. This product is intended to be installed and serviced by a qualied,
licensed electrician.
3. DO NOT connect directly to high voltage power. Install with a
compable Class 2 constant voltage LED driver (power supply).
4. Only install compable 12V and 24VDC constant voltage luminaires.
5. This product is rated for indoor installaon and is not protected
against moisture.
6. Do not modify product beyond instrucons or warranty will be void.

2 OF 5 IG050919-4.0
DMX ZONE CONTROLLER INSTALLATION GUIDE
®
1 2 3
Dynamic Mode
Short press changes mode/pauses
mode. Long press adjusts speed of
dynamic mode. See ‘Dynamic Mode
Chart’ for mode descripons.
Power
Short press to turn ALL zones and
channels ON/OFF.
RGB Brightness
Long press to adjust brightness of
RGB colors simultaneously (7 steps
of brightness). Adjust W (4CH)
channel seperately to adjust tone. Zone Control
Short press to conrtol zones 1, 2, or 3.
Long press to turn individual zone
ON/OFF.
Color Wheel
Adjust RGB color mixing. RGB ‘White’ Presets
Short press for 3 types of ‘White’ RGB presets:
warm white, neutral white, cool white. Useful
for applicaons that don’t ulize W (CH4) for
RGBW applicaons.
Power Indicator
Red indicates unit is OFF.
Blue indicates unit is ON.
Blue flash indicates DATA is transming.
R, G, B, W Channel Adjustment
Short press to turn channel ON/OFF.
Long press to adjust brightness.
MOBILE DEVICE OPERATION
The DMX controller can also be controlled remotely via WiFi with a
compable IOS/Android mobile device. Go to iOS or Google Play App
Store. Search for “EasyColor Pro” and download applicaon.
WIRING CONNECTIONS
INSTALLATION CONT.
DO NOT connect directly to 120VAC.
See ‘System Diagram’ for a general system design.
To DMX Decoder
or DMX Fixture
From 12-24V Driver
Reset
MOUNTING
Pop o faceplate with
a athead screwdriver.
Mount to a standard switchbox.
PAIRING CONTROLLER TO MOBILE DEVICE
1. Go to WiFi sengs of mobile device.
2. Connect to WiFi Network ‘EasyLighng’.
3. Type in Password ‘0123456789’.
4. Open EasyColor Pro Applicaon.

3 OF 5 IG050919-4.0
DMX ZONE CONTROLLER INSTALLATION GUIDE
PINOUT CONNECTION GUIDE
DYNAMIC MODE CHART
SETTING DMX ADDRESS
Each DMX decoder or DMX luminaire needs to be addressed correctly so the controller
can disnguish between each decoder. To pair a DMX decoder or luminaire to a specic
zone of the controller (1-3), set each decoder/luminaire to one of the following addresses:
• Zone 1: Set to address ‘001’ (will be xed to address 001 – 004)
• Zone 2: Set to address ‘005’ (will be xed to address 005 – 008)
• Zone 3: Set to address ‘009’ (will be xed to address 009 – 012)
Each zone of the controller is xed with 4 DMX addresses to control the 4 channels:
CH1 – Red, CH2 – Green, CH3 – Blue, CH4 – White or X.
Example of DMX Addressing Display
Digital Display
The following diagrams/tables indicate the appropriate connecons for patching your own CAT5/RJ45, and XLR-3 splice cables. These diagrams
are for general reference and may slightly dier between dierent cable manufacturers.
1 2 3 4 5 6 7 8
The Dynamic Mode tool plays factory-programmed
scenes. Choose up to 10 dierent scenes. Short
press switches/pauses the mode. Long press
adjusts speed of the dynamic mode.
Mode Descripon
1Fade 1 - B M R O Y G C
2Fade 2 - B G O W C M B
3Fade 3 - R W C G C W B W
4Skip 1 - R Y W C G W B M W Y
5RGB Fade In/Out
6RGB Fade In
7 RGB Fade Out
8 RGB Skip
9 Fade 4 - B M O G C
10 Fade 5 - W Y W M C W G W M C
11 All Channels O
Pin No. Wire Color Funcon
1White/Orange Data +
2 Orange Data -
3White/Green None
4Blue None
5White/Blue None
6Green None
7 White/Brown May be used as 2nd ground
8 Brown Ground
Pin No. Funcon
1Ground
2 Data -
3 Data +
Once DMX address is set on luminaire or DMX decoder, ensure to Press Zone 1, 2, or 3 on the controller to control desired zone.

4 OF 5 IG050919-4.0
DMX ZONE CONTROLLER INSTALLATION GUIDE
SYSTEM DIAGRAM
The following diagram is provided as an example system design. CAT5 (RJ45 connecons) data cables are the most cost-eecve soluon for
transming DMX-512 signals. XLR-3 cables may also be installed but require an addional adapter for connecng to DMX decoders. Always review
each component installaon guide for detailed and up-to-date wiring instrucons. Install in accordance with NEC and local regulaons.
AC Power
50/60Hz
L
N
Class 2 12-24VDC Driver**
Installed in Junction Box‡
G*
N
L
Input
Output
V+
V-
V+
V-
V+
CH1 - R
CH2 - G
CH3 - B
CH4 - W
0-5 0-9 0-9
Data IN
Data OUT
V+
V-
V+
CH1 - R
CH2 - G
CH3 - B
CH4 - W
0-5 0-9 0-9
Data IN
Data OUT
AC Power
50/60Hz
L
N
Class 2 12-24VDC Driver**
Installed in Junction Box‡
G*
N
L
Input
Output
V+
V-
CAT5 / Ethernet Cable (RJ45 Connections)
DMX Decoder
DMX Decoder
V- V+
V- V+
RGBW Tape Light / Fixture‡‡
V+ V+
CH1 R
CH2 G
CH3 B
CH4 W
V+ V+
CH1 R
CH2 G
CH3 B
Install applicable wire gauge / type
CH4 - W connection only utilized for RGBW / RGB(X) installation.
Wall Washer / DMX-512 Fixture‡‡
AC Power
50/60Hz
RJ45 / XLR-3
Adapter Connector
RGB Tape Light / Fixture‡‡
RJ45 Splice Cable
Wiring Connections
Brown Ground
White/Orange Data +
Orange Data -
White/Brown wire may be used as
an additional ground.
G
+
-
DMX Data
Output
RJ45 Coupler
DMX Controller
Installed in Wall Box‡
®
1 2 3
V+
V -
* Driver may not require a fault ground connecon. Refer to driver specicaons for addional informaon.
** Install a compable Class 2 constant voltage driver. It is recommended to load the driver no more than 80% its labeled rang for maximum longevity.
‡ Refer to driver specicaons for a compable juncon box.
‡‡ See luminaire specicaons for maximum series run limits.

5 OF 5
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2019 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG050919-4.0DMX ZONE CONTROLLER INSTALLATION GUIDE
TROUBLESHOOTING
For thorough troubleshoong of LED strip light and luminaires, see LED luminaire installaon guides.
LED luminaires not responding to touch
1. Ensure the blue indicator light is on by pressing ‘Power.’ A red indicator signies the device is o. The blue indicator light will blink rapidly when
pressing/holding any key on the touch pad.
2. Ensure the appropriate zone number was pressed prior to controlling the DMX decoder/luminaire. For example, if you know the luminaire is
addressed to zone 1, press ‘1’ prior to controlling.
3. Ensure the individual zone has not been turned o. Long pressing zones 1-3 will turn the specic zone ON/OFF. Addionally, long pressing R, G,
B, W will increase/decrease individual brightness and short pressing will turn R, G, B, W ON/OFF.
4. Ensure the DMX decoder/luminaire is addressed properly. For example, address ‘001’ will respond to zone 1 of the controller. See ‘Seng the
DMX Address’ for addional addressing informaon.
LED luminaire responding incorrectly
Ensure all wiring connecons are correct. Reversing the Data + and Data - will cause lights to icker and not respond to controller.
1. Check power connecons of all components (drivers, DMX decoders/luminaires, DMX controller).
2. Check DMX Data connecons - See Pinout Connecon Guide and System Diagram for RJ45 hard-wiring connecons.
3. Check DMX decoder connecons – See System Diagram for CH 1-4 connecons.
Visit the online product page at www.DiodeLED.com for addional product specicaons & warranty informaon.
• DMX WALL MOUNT ZONE CONTROLLER SPECIFICATION SHEET
For full specicaons.
• VOLTAGE DROP CHARTS
Use to specify appropriate wire gauge for installaon. Available at the ‘Resources’ page at www.DiodeLED.com.
ADDITIONAL RESOURCES