DIODE LED ENVI-LIGHT Color Tunable Mirror User manual

1 OF 5 IG110718-3.0
ENVI-LIGHT
®
Color Tunable Mirror INSTALLATION GUIDE
®ENVI-LIGHT® Color Tunable Mirror
INSTALLATION GUIDE
SKU DI-120V-ENV-MIR
Input 120V-277VAC 60HZ
Wattage 70 Watts
Dimensions 32.25 in. x 31 in. x 8 in. (W x H x D)
1.Install in accordance with national and local electrical
code regulations.
2.This product is intended to be installed and serviced by a
qualied, licensed electrician.
3.Do not modify or disassemble this product beyond
instructions or the warranty will be void.
4.Do not submerge, or install within 5 feet of a swimming
pool.
5.Failure to follow safety warnings, and installation
instructions will void the warranty for this product.
SAFETY & WARNINGS QUICK SPECS / MODELS
DRY LOCATION
120V-
277V
AC

2 OF 5 IG110718-3.0
ENVI-LIGHT
®
Color Tunable Mirror INSTALLATION GUIDE
ENVI-LIGHT® Color Tunable Mirror
INSTALLATION GUIDE
INSTALLATION
REQUIRED TOOLS
1
2
3
1. Phillips-head Screwdriver
2. Pencil
3. Ruler
TURN POWER OFF AT CIRCUIT
BREAKER
Prior to mounng, turn on power and
test connecon to ensure system is
operang properly. Turn o power again
before mounng.
REQUIRED COMPONENTS
1
2
1. ENVI-LIGHT®Color Tunable Mirror
2. Wall Mount
3. AC Power Cable
SHOCK HAZARD! May result in serious
injury or death.
Turn power OFF at circuit breaker prior to
installation.
3
1

3 OF 5 IG110718-3.0
ENVI-LIGHT
®
Color Tunable Mirror INSTALLATION GUIDE
ENVI-LIGHT® Color Tunable Mirror
INSTALLATION GUIDE
MARK WALL MOUNT ON SURFACE
SCREW WALL PLATE TO SURFACE
Using included mounting screws, fasten wall plate
to surface.
X
X
X
X
Locating two studs, mark drilling points for screw
mounts.
~16”
STUD
STUD
STUD
STUD
ATTACH BRACKETS TO BACK OF
ENVI-LIGHT®
Using included screws, fasten brackets to back of
ENVI-LIGHT®.
INSTALLATION (CONT.)
INSERT POWER CABLE INTO BACK
OF ENVI-LIGHT®
3
2
4
5

4 OF 5 IG110718-3.0
ENVI-LIGHT
®
Color Tunable Mirror INSTALLATION GUIDE
ENVI-LIGHT® Color Tunable Mirror
INSTALLATION GUIDE
INSTALLATION (CONT.)
MOUNT ENVI-LIGHT®TO WALL
PLATE
While pulling bracket straps down, place back of
ENVI-LIGHT® onto wall plate using hooks.
a
b
Place bottom of ENVI-LIGHT®brackets into wall
plate, then release straps allowing bracket to snap
into place.
PLUG ENVI-LIGHT®INTO WALL
OUTLET
TURN POWER ON AT CIRCUIT
BREAKER
6
7
8

5 OF 5
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | inf[email protected]om
© 2015 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG110718-3.0
ENVI-LIGHT
®
Color Tunable Mirror INSTALLATION GUIDE
ENVI-LIGHT® Color Tunable Mirror
INSTALLATION GUIDE
TROUBLESHOOTING
ADDITIONAL RESOURCES
Visit the on-line product page at www.DiodeLED.com for
full product specications, installation guides, and warranty
information.
ENVI-LIGHT®COLOR TUNABLE MIRROR
SPECIFICATION SHEET
SYSTEM WORKING IMPROPERLY?
Turn power OFF at circuit breaker and verify all connections.
Review SYSTEM DIAGRAMS and TROUBLESHOOTING or
call Diode LED Technical Support at 877.817.6028.
Symptom Common Cause
Fixture does not
illuminate • Circuit breaker is OFF or tripped.
For full product specications and warranty information.
OPERATION
TURN ON ENVI-LIGHT®AND ADJUST
COLOR TEMPERATURE
Turn dial clockwise until it clicks, and the xture
illuminates.
The further you turn the dial, the higher (ie. cooler)
the Color Temperature will be.
a
WARM WHITE
b
COOL WHITE
1