DIODE LED FENCER FOIL 2 User manual

1 OF 2 IG071717-2.0
FENCER®FOIL™2 INSTALLATION GUIDE
®
INSTALLATION GUIDE
FENCER®FOIL™ 2PREMIUM DIFFUSION
LED FIXTURE
DRY LOCATION
90+
HIGH CRI DIMMABLE
120VAC
INCLUDED MODELS / QUICK SPECS
Input Voltage ~120VAC / 50 ~ 60Hz
Maximum Series Run 300W
Ambient Temperature -4° ~ 122°F (-20° ~ 50°C)
Environment Indoor / Dry Locaons
INSTALLATION - UL LISTED 1598 HARD-WIRED LUMINAIRE
SKU Power Consumpon
DI-120V-FOIL-PDxx-12-yy 7W
DI-120V-FOIL-PDxx-18-yy 10W
DI-120V-FOIL-PDxx-24-yy 13W
DI-120V-FOIL-PDxx-32-yy 17W
xx - Indicates CCT (Kelvin); yy - Indicates color nish
1. Install in accordance with local and naonal electrical codes.
2. This product is intended to be installed and serviced by a licensed
electrician.
3. Turn power o at circuit breaker prior to installaon or servicing.
4. Risk of Electric Shock! Do not use any connecon pin to touch
electrical connecons.
5. For indoor use only. Do not install outdoors or in potenally combusve
environments.
6. Do not exceed 300W for daisy-chain series connecons.
7. Do not install this product in an environment outside the listed
ambient temperature.
8. Do not modify or disassemble this product beyond instrucons or the
warranty will be void.
9. See the ‘FENCER SERIES Dimmer Compability List’ for a list of
compable dimming controls.
DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!
Read all warnings and installaon instrucons thoroughly.
WARNING
WARNING! TURN MAIN POWER OFF BEFORE INSTALLING OR SERVICING!
Read all warnings and installaon instrucons thoroughly.
SAFETY & WARNINGS
Romex (NM) or BX Cable
Remove cover port of FENCER FOIL Direct Wire Switch & J-Box (DI-FOIL-
JBOX-**) to access wiring compartment. Included push-in wire connectors
should only be used with 12AWG wire. If using thinner gauge wire cut o
pre-aached connectors and make connecon with standard UL Listed
twisted wire connectors.
Line (HOT)
Neutral
Ground
Black
White
Green/Yellow
WIRING KEY
Push-in wire connectors
Use FENCER FOIL Extension Cable (DI-FOIL-**EXT-**) to connect
to FENCER FOIL Direct Wire Switch & J-Box (DI-FOIL-JBOX-**) or
link between FENCER FOIL xtures.
3/8” Romex Connector
Use FENCER FOIL 72 in. Power Cable
with Hard-Wire Connecon (DI-FOIL-
HWPWR-**) to connect to FENCER FOIL
Direct Wire Switch & J-Box (DI-FOIL-
JBOX-**). Hard-wired connecons must be
made in the FENCER J-box or other Listed
enclosure.
Use FENCER FOIL Linkable End-to-End Connector, one included,
(DI-FOIL-ETE-**) to link FENCER FOIL xtures together.
Ensure all terminal covers are
aached to open ports once
installaon is complete!
Terminal
Cover Terminal
Cover Screw

2 OF 2
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | inf[email protected]
© 2017 Elemental LED, Inc. All rights reserved. Specicaons are subject to change without noce.
IG071717-2.0FENCER®FOIL™2 INSTALLATION GUIDE
INSTALLATION - UL LISTED 153 PORTABLE LUMINAIRE
Use FENCER FOIL 72 in. Power Cable with
AC Plug (DI-FOIL-ACPWR-**) to connect to
electrical receptacle.
Use FENCER FOIL Linkable End-to-End Connector, one included,
(DI-FOIL-ETE-**) to link FENCER FOIL xtures together.
Use FENCER FOIL Extension Cable
(DI-FOIL-**EXT-**) to link FENCER
FOIL xtures together.
MOUNTING
Draw a guiding line before securing
mounng brackets to surface.
Mounng Brackets (included)
Use included Allen
key to loosen or
ghten set screw.
Secure mounng brackets to surface with screwdriver. To adjust
pivot angle, adjust ghtess with screwdriver and nish ghtening
with allen key and set screw.
NOTE: Mounng Brackets only pivot in one
direcon. See image below.
FENCER FOIL 72 in. Power Cable
with AC Plug (DI-FOIL-ACPWR-**)
connects to electrical receptacle.
FENCER FOIL 72 in. Power Cable with Hard-
Wired Connecon (DI-FOIL-HWPWR-**) must
be wired to FENCER FOIL Direct Wire Switch
& J-Box (DI-FOIL-JBOX-**) or other Listed
enclosure.