dipo INDUCTION TCK60-E User manual

2012-09-10
1
Caution
TCK60-E/TCK070-E/TCK113-E
DIH602-E/DIH070-E/DIH113-E
BK60-E/BK70-E/BK602-E
BK60S-E/BK70S-E/BK602S-E
DIBK226-E/DIBK235-E/DIBK261-E/DIBK218-E
DIBK226S-E/DIBK235S-E/DIBK261S-E/DIBK218S-E
DIHG900-E/DIHG450-E
Theory 4P
Cautions 5~9P
Specification 10~16P
How to Use 17~19P
Cleaning & Troubleshooting 20~21P
Installation 22~28P
Cookware for Induction 29P
Warranty Card 30~31P
User’s Manual
Read this manual,
before using the Range.
INSTRUCTIONS and SAFEGUARDS
1. Use an individual ELB having rated ampacity according to electric wiring
regulation before connecting to a distribution panel.
See page 22~23 for electrical wiring installation.
2. DO NOT block the air-intake or air-outflow panels as blocking may overheat
the unit.
3. Use pans 17cm or larger in diameter.
Please refer to 11 page for a list of suitable and unsuitable pans.
4. DO NOT touch the hot surface of the ceramic plate. NOTE: The induction
range itself does not produce any heat during cooking, however, the heat from
the pan will leave the surface of the ceramic hot!
5. DO NOT heat empty pots or pans. Heating an empty pan could automatically
activate the overheating protection function and the unit will shut off. An
empty pan can become dangerously hot, resulting in fire or personal injury.
6. Place the induction range on a horizontal surface and at least 10cm(4’’) away
from the wall and other objects for the proper ventilation.
7. DO NOT place any objects or tools in the air-intake panel. Doing so may
cause electrical shock.
8. To protect against electrical shock, DO NOT immerse the unit, the power
cable in water or other liquids.
9. Close supervision is necessary when the induction range is used or near
children.

2012-09-10
2
10. DO NOT operate the induction range if it has been damaged in any manner or
if the unit malfunctions. Return the unit to the nearest authorized service facility
for examination or repair.
11. The use of any accessories not recommended by the manufacturer may cause
injuries.
12. Keep the power cord away from heat.
13. DO NOT place the induction range in, on or near open flames, electric burners,
heated ovens or other high temperature surroundings.
14. DO NOT heat any sealed cans on the induction range. A heated can may
explode.
15. DO NOT move the induction range while cooking or when the pan is hot.
16. After the induction range has cooled down, power off at the circuit breaker of
unplug the and clean as follows, CERAMIC PLATE: wipe with damp cloth or use
a mild, non-abrasive cleaning solution.
BODY: wipe the control panel with soft cloth or use a mild cleaner.
17. DO NOT use induction range for other than intended use.
18. Power off at the circuit breaker or unplug when not in use.
19. When storing, DO NOT place any objects on top of the induction range.
20. When using an induction range (smooth top range) for cooking, keep your face
60cm from the heating areas.
SAVE THESE INSTRUCTIONS!!!
T H E O R Y
4
Theory of DIPO Induction
Induction Range
When the magnetic flux created
at the coil passes through the
bottom of the pot placed on the
top plate, eddy current is
generated around the flux.
This eddy current then is
transformed into heat by the
resistant element of the pan and
heats up the pan for cooking.
The features of Induction Range
◈ Save -> save up to 70%, no waste heat
◈ Clean -> spills don’t burn on. No combustion
products in the air.
◈ Fast -> cooks faster
◈ Safe -> safest cooking equipment

2012-09-10
3
5
Warning / Cautions
Warning / Cautions
Contents
Warning
Caution
S Y M B O L
Don’t touch! General
prohibition Important!
Be careful of
Electric shock!
Use of fire strictly
prohibited!
Indicates the possibility of severe injury or death .
Indicates the possibility of injury or damage to
the equipment.
Warnings / Cautions
6
Warning
Warnings / Cautions
1. Use a proper circuit breaker to standard.
<1 Phase> <3PH+N>
Don't use a damaged power
cable.
** If the supply
cable is damaged, it
must be replaced
by the manufacturer,
its service agent or
similarly qualified
persons in order to
avoid a hazard.
<3PH>
Don't bent or put strain on the
power cable.

2012-09-10
4
7
Warnings / Cautions
Warnings / Cautions
Don’t use in and unsafe place.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of
the appliance by a person
responsible for their safety.
Warning
Children should be supervised to
ensure that they do not play with
the appliance.
Be careful not to drop this appliance.Use only on a flat surface.
Don’t use in a wet environment.
Don’t install or use near an
electric heater or a gas range.
8
Warnings / Cautions
Warnings / Cautions
Don’t move or lift up product when
in use.
*It can cause a fire or a electric shock.
Don’t touch the hob surface, after
using range. It will be hot.
Metallic objects such as knives,
forks, spoons and lids should not
be placed on the hob surface since
they may get hot.
Don’t use the sharp tools, when
you clean this appliance.
WARNING : If the surface is cracked,
switch off the appliance and turn off
the circuit breaker to avoid
possibility of electric shock.
Warning
Don’t spray water on the range.
Be careful that the power cable is not
damaged or put under strain.
Don't use paint thinner,
benzene or gasoline, when you
clean this appliance.

2012-09-10
5
9
Warnings / Cautions
Warnings / Cautions
Warning
Keep electronics and magnetic
cards away from the ceramic
surface.
If you use pacemaker, consult with
doctor before using this appliance.
Do not block the exhaust vents.
Do not heat an empty pan or cook
dry ingredients.
Use vessels of the proper size.
If the oil starts smoking when oil
frying food, turn off the power!
Unplug or turn of the circuit
breaker when not in use.
*Use vessels with flat bottoms and a diameter of is
17cm~48cm. (6 ¾” – 19”)
10
SPECIFICATIONS
Specifications
Model
Watt
Voltage
Weight
Size
Heat Level
TCK070-E
7000W
8 Steps
MODEL: TCK60-E/TCK070-E/TCK113-E
24 Kg
AC 340~420V 3PH+N
50/60Hz
450 X 600 X 280 (mm)
Back Plate : 150 mm
Ceramic
Top Plate
Display
Power Button
Exhaust Vent
Mode Button
Min/Sec Button
Timer Button Start/Stop Button
External
Temperature
Sensor
Connector
Air Filter
TCK113-E
11000W
10 Steps
Control Knob
TCK60-E
5500W
10 Steps
Warm(7 Steps)
AC 220~240V
3PH 50/60Hz
Warm(7 Steps) Warm(7 Steps)

2012-09-10
6
11
SPECIFICATIONS
Specifications
MODEL: DIH602-E/DIH070-E/DIH113-E
Model
Watt
Voltage
Weight
Size
Heat Level
DIH070-E
44 Kg
600 X 750 X 370 (mm)
Back Plate : 630 mm
Ceramic
Top Plate
Display
Start Button
Exhaust Vent
Power Button
Mode Button
Min/Sec Button
Timer Button
Air Filter
External
Temperature
Sensor
Connector
Control Knob
DIH113-E
DIH602-E
7000W 11000W5500W
8 Steps 10 Steps10 Steps
AC 220~240V
3PH 50/60Hz
AC 340~420V 3PH+N
50/60Hz
Warm(7 Steps) Warm(7 Steps) Warm(7 Steps)
12
SPECIFICATIONS
Specifications
MODEL: BK602-E/BK60-E/BK70-E
Ceramic Top Plate
Power
Button
Start Button
Air Intake
Exhaust Vent
Display
Mode
Button
Min/Sec
Button
Timer Button
Model
Watt
Voltage
Weight
Size
Heat Level
External
Temperature
Sensor
Connector
Control Knob
BK60-E
26 Kg
400 X 600 X 250 (mm)
Exhaust Vent Plate : 30 mm
BK70-E
BK602-E
6000W 7000W5500W
8 Steps
Warm(7 Steps)
8 Steps
Warm(7 Steps)
10 Steps
Warm(7 Steps)
AC 220~240V
3PH 50/60Hz
AC 340~420V 3PH+N
50/60Hz

2012-09-10
7
13
SPECIFICATIONS
Specifications
MODEL: BK602S-E/BK60S-E/BK70S-E
Ceramic Top Plate
Power
Button
Start Button
Air Intake
Display
Mode
Button
Min/Sec
Button
Timer Button
Model
Watt
Voltage
Weight
Size
Heat Level
External
Temperature
Sensor
Connector
Control Knob
BK60S-E
26 Kg
400 X 530 X 250 (mm)
BK70S-E
BK602S-E
6000W 7000W5500W
8 Steps
Warm(7 Steps)
8 Steps
Warm(7 Steps)
10 Steps
Warm(7 Steps)
AC 220~240V
3PH 50/60Hz
AC 340~420V 3PH+N
50/60Hz
14
SPECIFICATIONS
Specifications
MODEL: DIBK-E Series
Model
Watt
Voltage
Weight
Size
Heat Level
AC 220~240V 50/60Hz
300 X 600 X 220 (mm)
Exhaust Vent Plate : 30 mm
Ceramic Top
Plate
Back
Burner
Display
Start
Button
Exhaust Hole
Start
Button Mode
Button Air Intake
Min/Sec
Button
Timer Button
Front
Burner
Display
External Temperature
Sensor Connector
Control Knob
DIBK218-E DIBK226-E DIBK235-EDIBK261-E
10 Steps
Warm (7 Steps)
10 Steps
Warm (7 Steps)
10 Steps
Warm (7 Steps)
8 Steps
Warm (7 Steps)
23.5 Kg 23.5 Kg 23.5 Kg
23 Kg
5200W
(2600W+2600W)
6600W
(3300W+3300W)
5900W
(2600W+3300W)
4000W
(2000W+2000W)

2012-09-10
8
15
SPECIFICATIONS
Specifications
MODEL: DIBKS-E Series
Model
Watt
Voltage
Weight
Size
Heat Level
AC 220~240V 50/60Hz
300 X 600 X 220 (mm)
Ceramic Top
Plate
Front
Burner
Display
Start
Button
Start
Button Mode
Button Air Intake
Min/Sec
Button
Timer Button
Back
Burner
Display
Control Knob
DIBK218S-E DIBK226S-E DIBK235S-E DIBK261S-E
10 Steps
Warm (7 Steps)
10 Steps
Warm (7 Steps)
10 Steps
Warm (7 Steps)
8 Steps
Warm (7 Steps)
23.5 Kg 23.5 Kg 23.5 Kg
23 Kg
5200W
(2600W+2600W)
6600W
(3300W+3300W)
5900W
(2600W+3300W)
4000W
(2000W+2000W)
16
SPECIFICATIONS
Specifications
MODEL: DIHG900-E/DIHG450-E
Power Button
Start
Button
Air Filter
Exhaust
Vent
Display
Grease
Can
Iron
Plate
Model
Watt
Voltage
Weight
Size
Heat Level
DIHG900-E
6600W
75 Kg
AC 220~240V 50/60Hz
900X600X280(mm)
<DIHG900-E>
<DIHG450-E>
Control
Knob
DIHG450-E
3300W
45 Kg
450X600X280(mm)
40~200℃
40~200℃

2012-09-10
9
17
HOW TO USE
How To Use
1. Connect the power cable.
2. Place a pot on the Ceramic Top Plate.
◆ Four lighted dots on the display indicates that the unit is plugged in.
◆ It must be placed in center of the ‘target’ on the Ceramic Top Plate.
3. Operation
◆ If you press the power button, “00” is displayed.
◆ If you want to start heating, press the START Button and turn the knob to right. At
first “01” is displayed.
◆ If you want to control Heat Level, spin knob to right(Max.10 Step) or to left(Min.H1
step).
4. How to use Timer Function
◆ Press the power button. “00” is displayed.
◆ Press the Timer Button. At first, "720" is displayed.
◆ Press the Min/Sec Button. "720" will blink. And then, if you spin the knob, you can control
cooking times.( From 1 Second to 720 Minutes )
◆ , If you want to adjust the seconds, (for times less than 100 minutes) Press the Min/Sec
Button one more time and the Seconds will blink. Use the knob to select the desired time.
◆ If you press the Start Button, the unit will start. If you want to control heat level, after press
the Timer Button, spin the knob.
BK(S)-E/TCK-E/DIH-E Series
Start
Button Power
Button
Control Knob
Min/Sec
Button
Timer
Button
5. Temperature Mode
◆ And then, press the Mode Button. "000C" is displayed.
◆ Press the power button. “00” is displayed.
◆ At the end of the set time, the operation will stop. Then if you press the start button one
more time, the product will start again with the same set time and heat level. But if you press
the power button, the set values are reset to Power Level 1 and 720 minutes.
the set value is reset at first.
◆ Press the start button. The display will show 40C, then set the cooking temperature by
turning the knob. The display will alternate between showing the actual temperature and
the set point.
◆ When the set point is reached, the display will stop changing.
★ If you press the Mode button and no temperture sensor is attached, the display will flash
E5.
★ The temperature sensor is optional and purchased separately.
☞DIPO is not responsible for damage to the equipment or
injuries caused by mis-use or negligence
18
HOW TO USE
How To Use
DIBK(S)-E Series
1. Connect the power cable.
Start Button
Power Button
Control Knob
Min/Sec Button
Time Button
Mode Button
2. Place a pot on the Ceramic Top Plate.
3. Operation
◆ If you press the power button, “00” is displayed.
◆ If you want to control Heat Level, spin knob to right(Max.10 Step) or to left(Min.H1
step).
☞DIPO is not responsible for damage to the equipment or
injuries caused by mis-use or negligence
◆ Four lighted dots on the display indicates that the unit is plugged in.
◆ It must be placed in the center of the ‘target’ on the Ceramic Top Plate.
◆ If you want to start operation, press the Start/Stop button and turn the knob to
right. At first, “01" is displayed.
4. How to use Timer Function
◆ Press the power button. “00” is displayed.
◆ Press the Timer Button. At first, "720" is displayed.
◆ Press the Min/Sec Button. "720" will blink. And then, if you spin the knob, you can control
the cooking times.( From 1 Second to 720 Minutes )
◆ If you want to adjust the seconds, (for times less than 100 minutes) Press the Min/Sec
Button one more time and the Seconds will blink. Use the knob to select the desired time.
◆ If you press the Start Button, the unit will start. If you want to control the heat level, after
press the Timer Button, then spin the knob.
◆ At the end of the set time, the operation will stop. Then if you press the start button one
more time, the unit will operate again with the same set time and heat level. But if you press
the power button, the set values are reset to Power Level 1 and 720 minutes.
5. Temperature Mode
◆ And then, press the Mode Button. "000C" is displayed.
◆ Press the start button. The display will show 40C. Then, set the cooking temperature by
turning the knob. The display will alternate between showing the actual temperature and
the set point.
◆ When the set point is reached, the display will stop changing.
If you press the Mode button and no temperature sensor is attached, the display will flash
E5.
★ The temperature sensor is optional and purchased separately.
◆ Press the power button. “00” is displayed.

2012-09-10
10
19
HOW TO USE
How To Use
DIHG900-E/DIHG450-E
Power Button
Start Button
Control Knob
Display
1. Insert the power plug.
◆Four lighted dots on the display indicates that the unit is plugged in.
.
2. Operation
◆If you press the power button, “000C” is displayed.
◆ If you press the Start button, “40C” is displayed, and the unit will
begin heating.
◆ Turn the control knob to adjust the set point from 40℃ to 200℃.
3. To Turn the Unit OFF
◆ Press the Power Button to stop operation and reset the temperature to
40C . Press the Start/Stop button to halt the current operation and retain
the temperature setting.
◆ This unit will run for a maximum of 12 hours. After 12 hours, press
the Start/Stop button to resume heating at the previously set
temperature.
◆ The display will alternate between the set point and the actual
temperature. When the set point is reached, the display will stop
changing.
☞DIPO is not responsible for damage to the equipment or
injuries caused by mis-use or negligence.
.
20
CLEANINGS
Cleanings
Cleanings
1. Cleaning ceramic top plate and control panel
◆ Do not use hard or sharp tools to clean the glass.
2. Clean the stainless steel case with a soft and dry cloth, or
dampen with a commercial stainless steel cleaner.
3. For products that have a removable air filter, remove and
clean the filter at least once per week, more if necessary..
◆The filter is located underneath the unit. Clean with a mild detergent and allow to air dry.
4. To clean the grease can, see the
illustration to the right.
( BK(S)-E & DIBK(S)-E Model Only )
◆ Remove the air vent cover and lift the grease can
out of the unit.
◆ Do not use sharp objects.
◆ Do not operate the unit without the grease
can and cover in place.
5. For DIHG-E Model Griddles, clean the cooking surface with
mild detergents only.
◆ Do not use acid based detergents as this will damage the surface.
◆ Immediately after cleaning the griddle surface, season with cooking oil.
◆ Light stains : Clean the top plate with the soft and wet cloth.
◆ Severe stains : Use a soft cloth with a mild cleaning agent or detergent.
★ Caution : Unplug the unit and allow to cool before cleaning.
◆ Clean using a mild detergent.

2012-09-10
11
21
TROUBLESHOOTING
Troubleshooting
세척 및 유지 방법
Troubleshooting
Symptoms Measure Methods
Display is Blank
◆Check that the unit is plugged in and/or the breaker is
on.
◆Check that voltage is present at the unit.
◆Contact the Factory.
Power on, but pan
not heating.
◆Check that a pot is proper for Induction Range or that a
pot is placed in center of the top plate.
◆Contact the Factory.
Unit stops heating
Or output is
weakened.
◆Check the surrounding temperature.
◆Check the product's ventilation.
◆Check that the temperature of the ceramic top plate is above 500F.
◆Check that the pan is properly placed.
◆ Check the set timer value.
◆Check if the 12 hour maximum run time has been exceeded.
Etc…
(display
ed)
U, 00 ◆Make sure you have a valid pan.
◆Check that the pan has a flat bottom.
E4, E6 ◆Turn off and unplug the unit. Allow the unit to cool off.
Plug back in and try again.
E5 ◆Check that the temperature sensor is connected to the product correctly.
◆"E5" error means that the sensor isn't connected to the product.
E2,E3,E7 ◆Unplug or turn of the breaker for at least 1 minute, plug
back in and try again
E1,E8,E9 ◆Contact the Factory.
22
INSTALLATION
Installation
Installing Electricity
1. 380V 3 Phase circuit breaker
•Electrical specification
- 340~420V 3PH+N (Plus GND)
- Use circuit breaker with proper
ratings
- cable : Above 600V, 5 Wires
: Below 7kw(Wire Diameter : Above 4￠)
: Below 11kw(Wire Diameter : Above 6￠)
2. 220V 3 Phase circuit breaker
•Electrical specs according
to Models
Model Output Ampere Voltage
TCK070-E 7kw 11.5A 340~420V 3PH+N
TCK113-E 11kw 16A 340~420V 3PH+N
DIH070-E 7kw 11.5A 340~420V 3PH+N
DIH113-E 11kw 16A 340~420V 3PH+N
BK60(S)-E 5.5kw 8.5A 340~420V 3PH+N
BK70(S)-E 7kw 11.5A 340~420V 3PH+N
•Electrical specification
- 220~240V 3PH (Plus GND)
- Use circuit breaker with proper
ratings
- cable : Above 400V , 4 Wires
Model Output Ampere Voltage
TCK60-E 6kw 15A
220~240V 3PH
DIH602-E 6kw 16A
220~240V 3PH
BK602(S)-E 6kw 15A
220~240V 3PH
•Electrical specs according to
Models

2012-09-10
12
23
INSTALLATION
Installation
Installing Electricity
3. 220V 1 Phase Circuit Breaker
•Electrical specification
- 220~240V 1PH (Plus GND)
- Use circuit breaker with proper ratings
- cable : Above 400V, 3 Wires
: Below 7kw (Wire Diameter : Above 4￠)
Model Output Ampere Voltage
DIBK226(S)-E 5.2kw 24A 220~240V 1PH
DIBK235(S)-E 6.6kw 30A 220~240V 1PH
DIBK261(S)-E 5.9kw 27A 220~240V 1PH
DIBK218(S)-E 4kw 18A 220~240V 1PH
DIHG900-E 6.6kw 30A 220~240V 1PH
DIHG450-E 3.3kw 16A 220~240V 1PH
★ Caution : When you install DIHG450-E Models, each unit
must have be installed on a dedicated circuit.
24
INSTALLATION
Installation
BK-E Series
Hole Size
5. Hole Size of Control Panel
Size of Product
580mm
380mm
Front Part Holes of
case for built-in
Holes
For sufficient ventilation
the holes as right
picture are required.
2. Space of 10cm (4”) and open louvers in front of the unit is required
for ventilation.
4. Cut-out size for Products
3. For Drop-in units, be sure the counter top is adequately reinforced
to bear the weight of the unit in operation. Additional support under
the unit may be required.
1. Match cut-out size to the product.
235mm
300mm
60mm
50mm
40mm
50mm
290mm
239mm
54mm
2-C10mm
400m
250mm
600mm

2012-09-10
13
25
INSTALLATION
Installation
BKS-E Series
Hole Size
5. Hole Size of Control Panel
Size of Product
511mm
380mm
Mounting of controls
and louvers
Louvers
For sufficient ventilation
the holes as right
picture are required.
2. Space of 10cm and open louvers in front of the unit is required for
ventilation.
4. Cut out size for Products
3. For Drop-in units, be sure the counter top is adequately reinforced
to bear the weight of the unit in operation. Additional support under
the unit may be required.
1. Match cut-out size to the product.
235mm
300mm
60mm
50mm
40mm
50mm
290mm
239mm
54mm
2-C10mm
400mm
530mm
250mm
제품 설치
Installation
DIBK-E Series
Holes
578mm
278mm
26
INSTALLATION
2. Space of 10cm and holes to front of product is needed for
ventilation.
4. Hole Size of Products
3. When products have been built-in, reinforcement stand is required
in order to bear weight of products.
1. Match size of hole with size of product as possible.
Size of Product Hole Size
For sufficient ventilation
the holes as right
picture are required.
5. Hole Size of Control Panel
Hole Size
600mm
300mm
220mm
Front Part Holes of
case for built-in

2012-09-10
14
Installation
DIBKS-E Series
Holes
27
INSTALLATION
2. Space of 10cm and holes to front of product is needed for
ventilation.
4. Hole Size of Products
3. When products have been built-in, reinforcement stand is required
in order to bear weight of products.
1. Match size of hole with size of product as possible.
Size of Product Hole Size
For sufficient ventilation
the holes as right
picture are required.
5. Hole Size of Control Panel
Hole Size
578mm
278mm
300mm
220mm
Front Part Holes of
case for built-in
Installation
DIBKS-E Series
28
INSTALLATION
6. In case of DIBKS-E Model, the ventilation and the air flow guide of
product’s back is needed.
Back of Case
Picture of Case
7. Ventilation Holes and Air Flow Guide
Hole of
Power
Cable
Ventilation
Holes
Air Flow
Guide

2012-09-10
15
29
INDUCTION COOKWARE
Induction Cookware
BKP/BK 설치 가이드
Selecting proper pots
TCK-E Series
BK(S)-E Series
17~36cm
DIH-E Series
DIBK218(S)-E
Pan Bottom Diameter
Model
17~48cm
DIBK(S)-E Series
(Except DIBK218(S)-E)
11~24cm
12~24cm
1. Bottom of pots must be flat.
2. Bottom Materials of Pots : Iron, Cast Iron, Enameled Iron, Stainless
Steel(Magnetic), Triple Bond Steel and Magnetic Pots
3. Don't use!! : Non-ferrous metal, Glass, Aluminum, Copper, Mesh for Grill,
or pots with concave bottoms
★Please use pots that have IH exclusive marks.
Warranty
0
Limited Warranty Statement
All commercial cooking equipment manufactured by DIPO is warranted
against defects in materials and workmanship for a period of one year
from the date of invoice. Accessories, cookware and other incidental
non-range items sold by DIPO are warranted against defects in
materials and workmanship for a period of 90 days.
IMPORTANT! A valid proof of purchase (s) showing date of purchase
and Serial Number is required to obtain Warranty Service.
This warranty is for the benefit of the original purchaser and is non-
transferable. Any defects in materials or workmanship, which are
brought to the attention of DIPO by written notification within the
stated warranty period will be repaired or replaced at DIPO’s discretion,
with new or recertified products or parts.
THIS IS THE SOLE REMEDY FOR ANY BREACH OF THIS WARRANTY. IN
NO EVENT WILL DIPO BE LIABLE FOR DAMAGES OF ANY KIND,
WHETHER DIRECT OR INDIRECT, SPECIAL OR CONSEQUENTIAL. THIS
WARRANTY IS THE COMPLETE AND ONLY WARRANTY, EXPRESS OR
IMPLIED IN LAW OR FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY, SUITABILITY, QUALITY, OR
FITNESS FOR ANY PARTICULAR PURPOSE. THIS WARRANTY DOES NOT
INCLUDE ANY THIRD PARTY INSTALLATION, REMOVAL OR DAMAGE
COSTS including (but not limited to) LABOR, MATERIALS AND TRAVEL
FOR CAULKING IN DROP-IN (“BUILT-IN”) UNITS, OR REPAIRS /
REPLACEMENT OF FUSES, BREAKERS, MILLWORK AND / OR COUNTER-
TOPS).

2012-09-10
16
Warranty
0
This warranty is void if it is determined upon inspection by DIPO or one
it’s Authorized agents that the equipment has been modified, misused,
misapplied, improperly installed, or damaged in transit or by fire, flood
or act of God. Broken Glass-Ceramic tops are considered abuse and are
NOT covered. Warranty will be considered void if the serial nameplate
has been removed or defaced or if the unit has been opened or
modified in any way or service has been attempted by unauthorized
personnel.
This warranty is valid only for equipment purchased through an
authorized DIPO Representative or Dealer.
To receive Warranty Service, please call DIPO Customer Service at
[phone]. A Return Merchandise Authorization (RMA) number
will be issued along with instructions for returning goods for service (or
their replacement). The RMA number must be written clearly or printed
on the outside of the return shipping container, or on the address label
when returning units for service. Units received without an RMA number
will be refused at our shipping dock and may encounter a delay in
service. Units must be taken or shipped to DIPO USA for service with
transportation charges prepaid.
DIPO will provide return freight. DIPO assumes no liabilities whatsoever
for any damages incurred in transit. PLEASE BE SURE TO USE
ADEQUATE PACKAGING AND A RELIABLE SHIPPING METHOD. IF THE
UNIT IS BEING REPLACED, USE THE SAME BOX THE REPLACEMENT UNIT
ARRIVED IN FOR THE RETURN.
TEL : [phone]
www.dipoelec.com
Rm402, Hanamventure Center, 523 Chang-u-dong,
Hanam-si, Gyeonggi-do 465-120, Korea
FAX : [phone]
E-MAIL : [e-mail]