Directed Electronics 10 User manual

MMooddeell1100
➤
OOwwnneerr’’ssGGuuiiddee

3
© 2005 directed electronics, inc.
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or
replace with a comparable reconditioned model any Directed unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated sensors and
accessories, which proves to be defective in workmanship or material under reasonable use
during the lifetime of the vehicle provided the following conditions are met: the unit was
professionally installed and serviced by an authorized Directed dealer; the unit will be pro-
fessionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: con-
sumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote trans-
mitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial num-
ber is defaced, missing or altered; the unit has been modified or used in a manner con-
trary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materi-
als or construction. The warranty does not cover damage to the unit caused by installa-
tion or removal of the unit. Directed, in its sole discretion, will determine what consti-
tutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-
AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-
ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

4© 2005 directed electronics, inc.
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or con-
sequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-
876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-
soever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Your full name and address
➤Authorized dealer's company name and address
➤Type of alarm installed
➤Year, make, model and color of the automobile
➤Automobile license number
➤Vehicle identification number
➤All security options installed on automobile
➤Installation receipts

5
© 2005 directed electronics, inc.
ttaabblleeooffccoonntteennttss
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy..............................................................................33
ssttaannddaarrddttrraannssmmiitttteerrccoonnffiigguurraattiioonn................................................................................77
wwhhaattiissiinncclluuddeedd............................................................................................................88
iimmppoorrttaannttiinnffoorrmmaattiioonn..................................................................................................88
system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ttrraannssmmiitttteerrffuunnccttiioonnss..................................................................................................1100
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
uussiinnggyyoouurrssyysstteemm......................................................................................................1122
active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
disarming without a transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
dome light control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
one-time bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
aauuxxiilliiaarryyoouuttppuuttss((ooppttiioonnss))..........................................................................................2222
ddiiaaggnnoossttiiccss..................................................................................................................2233
arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ccooddeehhooppppiinngg..............................................................................................................2266
hhiigghhffrreeqquueennccyy............................................................................................................2277
oowwnneerrrreeccooggnniittiioonn......................................................................................................2277
rraappiiddrreessuummeellooggiicc......................................................................................................2288
ppoowweerrssaavveerrmmooddee......................................................................................................2288
pprrooggrraammmmiinngg..............................................................................................................2299
iinnssttaallllaattiioonnooppttiioonnss....................................................................................................3322

6© 2005 directed electronics, inc.
vveehhiicclleerreeccoovveerryyssyysstteemm((vvrrss®®))....................................................................................3333
arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
disarming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
pprrooggrraammmmiinnggooppttiioonnss..............................................................
..................................3366
sshhoocckksseennssoorraaddjjuussttmmeenntt............................................................................................3388
enter shock sensor adjustment mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
adjusting the shock sensor setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
exit shock sensor adjustment mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
reset shock sensor to default setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
sseeccuurriittyy&&ccoonnvveenniieenncceeeexxppaannssiioonnss..........
..................................................................4411
gglloossssaarryyoofftteerrmmss........................................................................................................4433
qquuiicckkrreeffeerreenncceegguuiiddee..................................................................................................4455

7
© 2005 directed electronics, inc.
ssttaannddaarrddttrraannssmmiitttteerrccoonnffiigguurraattiioonn
controls the LLoocckk––AArrmm//PPaanniiccOOnn//PPaanniiccOOfffffunction.
controls the UUnnlloocckk––DDiissaarrmm//PPaanniiccOOfffffunction.
controls SSiilleennttMMooddee™™and an AAuuxxiilliiaarryyOOuuttppuutt((22)).
controls the PPaanniic
cOOnn//OOfffffunction.
and pressed together control an AAuuxxiilliiaarryyOOuuttppuutt((33)).
and pressed together control an AAuuxxiilliiaarryyOOuuttppuutt((44)).
and pressed together control an AAuuxxiilliiaarryyOOuuttppuutt((55)).
and pressed together control an AAuuxxiilliiaarryyOOuuttppuutt((66)).

8© 2005 directed electronics, inc.
wwhhaattiissiinncclluuddeedd
➤One control module
➤A pair of four-button transmitters
➤Wire harnesses
➤The 514N six-tone programmable siren
➤The status LED indicator light
➤A push-button Valet switch
➤Your warranty registration
➤Failsafe®Starter Kill ready circuitry
(may require additional labor)
➤XHF+ external receiver/antenna
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. Due to the complexity of this system,
it must be installed by an authorized dealer only. Installation of
this product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with preprinted dealer certifi-
cates to verify that they are authorized.
This owner’s guide should help you to get the most out of your
system. Please take the time to read it prior to using the system.

9
© 2005 directed electronics, inc.
system maintenance
The system requires no specific maintenance. Your remote
control is powered by a small, lightweight 3 volt lithium battery
(CR2032) that will last approximately one year under normal
use. When the battery weakens, operating range will be reduced
and the LED on the remote will dim.
your warranty
Your warranty registration must be returned and the bar code
serial number must not be removed. If the warranty registration
is not returned, you do not have a warranty. It is also necessary to
keep your proof of purchase, which reflects that the product was
installed by an authorized dealer. Make sure that you receive the
warranty registration from your dealer.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
➜
➜
➜

10 © 2005 directed electronics, inc.
ttrraannssmmiitttteerrffuunnccttiioonnss
This system uses a computer-based learn routine to learn the
transmitter buttons. This makes it possible to assign any trans-
mitter button to any system function. The transmitter initially
comes programmed with Standard Configuration, but may also
be customized by an authorized dealer. The buttons described in
this manual correspond to a Standard Configuration transmitter.
standard configuration
Button
The arming function is controlled by pressing this button for
one second.
Button
The disarming function is controlled by pressing this button for
one second.
➜
3101 Series

11
© 2005 directed electronics, inc.
Button
Silent Mode™ and an optional auxiliary function are controlled
by pressing this button. (Silent Mode works by pressing this
button for less than one second before arming or disarming. An
optional auxiliary function, such as trunk release, can be
controlled by pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.

12 © 2005 directed electronics, inc.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.
uussiinnggyyoouurrssyysstteemm
The buttons described in this manual correspond to the standard
configuration. Remember, this is not the only way your trans-
mitter may be set up. It can be custom configured to meet your
needs.
active arming
You can activate, or arm, the system by pressing on your
transmitter for one second. When the system arms, you will hear
a short siren sound, or chirp, and the parking lights will flash
once. If the vehicle’s power door locks have been connected to
the system, the doors will lock.
➜

13
© 2005 directed electronics, inc.
While the system is armed, the status LED will flash approxi-
mately once per second, indicating that the system is actively
protecting your vehicle. If you hear a second chirp after arming,
and see the status LED flashing in groups, refer to the
Diagnostics
section of this guide. This extra chirp is called Bypass Notification.
passive arming
The system also can be programmed to arm itself automatically
(called passive arming). If the system is programmed for passive
arming, it will automatically arm 30 seconds after the ignition is
turned off and the system "sees" you leave the vehicle by opening
and closing a door. Whenever the system is in its 30-second
passive-arming countdown, the status LED will flash twice as
fast as it does when the system is armed. The siren will chirp
once 20 seconds after the last door has been closed. The system
is not actually armed at that point. The system arms and the
doors lock (if connected and programmed for passive locking) at
the 30 second mark, but the siren will not chirp. The early chirp
provides you with a 10-second warning prior to arming.
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm (unless forced passive arming is pro-
grammed on). See Programming Options section of this
guide. Additionally, each time a protected entry is trig-
gered during the arming countdown, the 30-second
countdown starts over.
➜

14 © 2005 directed electronics, inc.
When armed, your vehicle is protected as follows:
➤Light impacts will trigger the Warn Away®signal. When
triggered, the siren will chirp and the parking lights will flash
for a few seconds.
➤Heavy impacts will trigger the system. The triggered
sequence is between 1-180 seconds of constant siren and
flashing parking lights.
➤If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the sys-
tem with your transmitter if you inadvertently open the door
while the system is armed, while still providing an instant
response (even if the door is immediately closed).
➤Turning on the ignition key will trip the same two-stage
response as opening a door.
➤The optional starter kill prevents the vehicle’s starter from
cranking.
multi-level security arming
Multi-Level Security Arming allows you to select which of the
security system's inputs or sensors will be active and which will
be bypassed at the time that the system is armed. (See the
Table
of Zones
section of this guide.) Pressing again within five
seconds of arming the security system will activate the Multi-
Level Security Arming feature. Each time is pressed again, a
different security level is selected. The different security levels
can be selected as follows:
➜

15
© 2005 directed electronics, inc.
➤Press one time: The parking lights flash once. The
system is armed.
➤Press a second time within five seconds: The parking
lights flash twice. Zone 2 is now bypassed.
➤Press a third time within five seconds: The parking
lights flash three times. Zone 4 is now bypassed.
➤Press a fourth time within five seconds: The parking
lights flash four times. Zone 7 is now bypassed.
➤Press a fifth time within five seconds: The parking
lights flash five times. Zones 2 and 4 are now bypassed.
➤Press a sixth time within five seconds: The parking
lights flash six times. Zones 2 and 7 are now bypassed.
➤Press a seventh time within five seconds: The parking
lights flash seven times. Zones 4 and 7 are now bypassed.
➤Press an eigth time within five seconds: The parking
lights flash eight times. All input zones, except zone 5, are
now bypassed.
➤Continued pressing of will begin the Multi-Level
Security Arming cycle over again.
note: Multi-Level Security Arming only applies to a sin-
gle arming cycle. Once the system is disarmed and then
re-armed, all the zones will be active again.

16 © 2005 directed electronics, inc.
disarming
To disarm the system, press . You will hear two chirps, and
the parking lights will flash twice. If the power locks are
connected to the system, the doors will unlock. If the siren chirps
either four or five times when disarming, refer to the
Diagnostics
section of this guide. This is called Tamper Alert.
high security disarm
This security system offers High Security Disarm. High Security
Disarm is a feature that makes it possible to silence and reset the
system while it is triggering, without disarming the system. If the
system is triggered and the siren has been sounding for longer
than six seconds, pressing or on the remote transmitter
will stop the trigger and return the unit to the armed state. The
system will not disarm, but rather reset. This prevents you from
disabling the system should you wish to disarm it without visu-
ally checking the vehicle. Pressing after resetting the system
will disarm the system; pressing this button during the first six
seconds of the triggered sequence will disarm the security system
immediately. The six second timer is provided for your conve-
nience, in case the system is accidentally triggered.
➜
➜

17
© 2005 directed electronics, inc.
disarming without a transmitter
This feature allows you to disarm the security system without the
remote transmitter should it be lost, damaged, or disabled. In order
to disarm the system without a remote transmitter, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON posi-
tion. Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
Location of Valet Button_________________________________
Number of Pulses______________________________________
important! The unit can be programmed to respond to
one to five pulses of the Valet button for the disarm func-
tion. Be sure to check with the installer for the desired
programming.
DRW-35
➜

18 © 2005 directed electronics, inc.
dome light control
security only
The dome light activates for 30-seconds after the system is
disarmed.
Ignition controlled
The dome light activates for 30-seconds after the ignition is
turned On.
door controlled
The dome light activates for 30-seconds after the system sees a
door has closed. (If door was held open for longer than 3
minutes the dome light will not illuminate.)
full
The dome light activates for 30-seconds after seeing door
closure, ignition, or security disarm. (This is the
factory setting.)
silent mode
To temporarily turn off the arm or disarm chirps, use Silent
Mode™. Simply press for less than one second before
arming or disarming, and the confirmation chirp(s) will be elim-
inated for that one operation only. If you want the arm/disarm
chirps turned off permanently, your dealer can do this for you.
note: The Warn Away®response to lighter impacts is
bypassed if the system is armed using Silent Mode. This
ensures that no chirps will be emitted by the siren in an
area you want chirp-free. The system is still fully capable
of triggering. Only the Warn Away®response is bypassed.
➜
➜

19
© 2005 directed electronics, inc.
panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your transmitter. Just
press or for two seconds, and you will enter Panic
Mode. The siren will sound and the parking lights will flash for
the programmed siren duration. To stop Panic Mode at any time,
press , or on the remote transmitter again.
valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the remote transmitter,
but all convenience functions (door locks, trunk release, etc.)
will continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
DRW-35
➜
➜

20 © 2005 directed electronics, inc.
To enter or exit Valet Mode using the transmitter:
1. Open any vehicle door.
2. Press .
3. Press .
4. Press again.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
one-time bypass
This feature stops the alarm from arming or activating any
outputs that are programmed to activate when the alarm is
armed.
One-time bypass will defeat the following actions:
Passive arming: If programmed ON the alarm will not arm
itself.
If the remote is used to arm the alarm after exiting the vehicle:
Window roll up: If programmed ON this output will not
activate.
Linked Auxiliary Outputs: If programmed to activate on
arm, they will not activate.
To activate one-time bypass:
1. After parking turn the ignition off.
2. Turn the ignition On for more than 1-second and less than
3-seconds.
3. The siren will chirp once to indicate one-time bypass has
been activated.
➜

21
© 2005 directed electronics, inc.
To cancel one-time bypass perform one of the following:
Arm then disarm the alarm.
Turn the ignition On for more than 3-seconds.
nuisance prevention®circuitry
Your system has Directed’s Nuisance Prevention®Circuitry
(NPC®). It prevents annoying repetitive trigger sequences due to
faulty door pin switches or environmental conditions such as
thunder, jackhammers, airport noise, etc.
Example
If the alarm triggers three times within a 60-minute period and
each time the same sensor or switch triggers the alarm, NPC®will
interpret those triggers as false alarms. After the third trigger,
NPC®ignores, or bypasses, that sensor or switch (along with any
other sensors or switches sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the system while it is being
bypassed, the 60-minute bypass period will start over. This ensures
that a sensor that continually triggers will remain bypassed.
Doors are covered by NPC®differently; if the alarm is triggered
by an open door for three full cycles, the doors will be bypassed
until the trigger ceases.
note: Arming and disarming the system does not reset this
function.The only ways to reset a bypassed zone are for it
to not trigger for 60 minutes, or to turn on the ignition. If
testing your system, it is important to remember that the
NPC®programming can cause zones to be bypassed and
appear to stop working. If five chirps are heard when dis-
arming, NPC®has been engaged. If you wish to clear the
NPC®memory, turn the ignition key on.
➜