Directed Electronics Viper 771XV User manual

MMooddeell777711XXVV
➤
OOwwnneerr’’ssGGuuiiddee

i
© 2004 directed electronics—all rights reserved
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics ("Directed") promises to the original purchaser to repair or replace
with a comparable reconditioned model any Directed unit (hereafter the "unit"), exclud-
ing without limitation the siren, the remote transmitters, the associated sensors and acces-
sories, which proves to be defective in workmanship or material under reasonable use dur-
ing the lifetime of the vehicle provided the following conditions are met: the unit was pro-
fessionally installed and serviced by an authorized Directed dealer; the unit will be pro-
fessionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: con-
sumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote trans-
mitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial num-
ber is defaced, missing or altered; the unit has been modified or used in a manner con-
trary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materi-
als or construction. The warranty does not cover damage to the unit caused by installa-
tion or removal of the unit. Directed, in its sole discretion, will determine what consti-
tutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-
AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-
ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

ii © 2005 directed electronics—all rights reserved
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or con-
sequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-
876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-
soever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Your full name and address
➤Authorized dealer's company name and address
➤Type of alarm installed
➤Year, make, model and color of the automobile
➤Automobile license number
➤Vehicle identification number
➤All security options installed on automobile
➤Installation receipts

1
© 2005 directed electronics—all rights reserved
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii
wwhhaattiissiinncclluuddeedd....................................................................
..........................................33
iimmppoorrttaannttiinnffoorrmmaattiioonn...................................
.................................................................33
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
22--wwaayyrreemmootteeddiiaaggrraamm...........
.........................................................................................55
ssttaannddaarrdd
rreemmootteeccoonnffiigguurraattiioonn........................................................................................55
ssttaannddaarrddrreemmootteebbuuttttoonnccoonnffiigguurraattiioonn......................................................
......................66
22--wwaayyrreemmootteeffuunnccttiioonnss......................................................
............................................88
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
rreemmootteeooppeerraattiioonn....................................
....................................................................1100
system signal paging features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Out of Range Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
pprrooggrraammmmiinnggrreemmoottee.........
...........................................................................................1122
uussiinngg
yyoouurrssyysstteemm........................................................................................
................1133
warning! safety first. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
arming while driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
disarming without a 2-way remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
remote start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
short-run/turbo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AAuuxxiilliiaarryyOOuuttppuuttss((OOppttiioonnss))..................................................
......................................2299
ssaaffeettyyffeeaattuurreess............................................
....................................................................3300
starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
over and under rev protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ttaabblleeooffccoonntteennttss

2© 2005 directed electronics—all rights reserved
nuisance prevention circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ddiiaaggnnoossttiiccss........................................................................................
..........................3333
arming diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ccooddeehhooppppiinngg.........................................................
.....................................................3366
hhiigghhffrreeqquueennccyy..............................
..............................................................................3377
oowwnneerrrreeccooggnniittiioonn..
....................................................................................................3377
rraappiiddrreessuummeellooggiicc...............................................................................
.......................3388
ppoowweerrssaavveerrmmooddee..........................................................
............................................3388
pprrooggrraammmmiinnggooppttiioonnss..................................
..............................................................3399
sseeccuurriittyy&&ccoonnvveenniieenncceeeexxppaannssiioonnss..
..........................................................................4422
gglloossssaarryyoofftteerrmmss......
..................................................................................................4433
qquuiicckkrreeffeerreenncceegguuiiddee..............................................................................
....................4477

3
© 2005 directed electronics—all rights reserved
wwhhaattiissiinncclluuddeedd
➤A control module
➤An XHF2 transceiver/antenna
➤One 4-button 2-way remote
➤One 4-button remote
➤A Stinger™ DoubleGuard®two-stage shock sensor
➤A Revenger™ Soft Chirp™ six-tone programmable siren
➤A status LED indicator light
➤A push-button Valet switch
➤Your warranty registration
➤A shut-down toggle switch
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your combination remote
start alarm system. Due to the complexity of this system, it must
be installed by an authorized dealer only. Installation of this
product by anyone other than an authorized dealer voids the
warranty. All dealers are provided with a preprinted dealer certif-
icate to verify authorization.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.directed.com.

4© 2005 directed electronics—all rights reserved
your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Make sure you receive the warranty registration from your dealer.
It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
caution
This product is designed for fuel injected, automatic transmission
vehicles only. Use of this product in a standard transmission
vehicle is dangerous and contrary the product's intended use.
➜
➜
➜

5
© 2005 directed electronics—all rights reserved
22--wwaayyrreemmootteeddiiaaggrraamm
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonn
1. Unlock/Lock Indicator (Orange)
2. Receive/Transmit Indicator (Green)
3. Remote Start/Auxiliary Indicator (Yellow)
4. Panic Indicator (Red)
5. Lock Button
6. Unlock Button
7. Remote Start Button
8. Auxiliary Channel Button
1
2
3
4
56
78

6© 2005 directed electronics—all rights reserved
ssttaannddaarrddrreemmootteebbuuttttoonnccoonnffiigguurraattiioonn
controls the AArrmmand PPaanniiccOn/Off function.
controls the DDiissaarrmmand PPaanniiccOff function.
controls SSiilleennttMMooddee™™and AAuuxxiilliiaarryychannel 22output.
controls the RReemmootteeSSttaarrttfunction.
and pressed together control the TTiimmeerrmode.
and pressed together control TTuurrbboo//SShhoorrttRRuun
n.
and pressed together control channel 44output.
and pressed together control channel 5 output.
and and pressed together control the rear
defogger.
and pressed together control channel 6 output.

7
© 2005 directed electronics—all rights reserved
ssyysstteemmmmaaiinntteennaannccee
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
Low Battery Notification
If the battery is low (and this feature is programmed On) the 2-
way remote will emit 2 long beeps 5-seconds after a transmission
is completed. The 2 long beeps will repeat every 25 seconds up to
3 times (or until a 2-way remote button is pressed).
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the remote
control observing the correct polarity. When power is returned
the remote control will light all icons and generate melodies
(representing all beeper tones).

8© 2005 directed electronics—all rights reserved
22--wwaayyrreemmootteeffuunnccttiioonnss
The receiver uses a computer-based Learn Routine to learn the 2-
way remote buttons. This makes it possible to assign any 2-way
remote button to any receiver function. The 2-way remote
initially comes programmed with Standard Configuration, but
may also be customized by an authorized dealer. The buttons in
all of the instructions in this manual correspond to a Standard
Configuration 2-way remote.
standard configuration
Button
The arming function is controlled by pressing this button for
one second. Pressing and holding this button for more than
3-seconds will trigger the panic mode.
Button
The disarming function is controlled by pressing this button for
one second. Pressing this button during panic mode will turn off
the panic mode.
Button
Silent Mode™ and an optional auxiliary function are controlled
by this button. (Silent Mode works by pressing this button for
less than one second before arming or disarming. An optional
auxiliary function, such as trunk release, can be controlled by
pressing this button for 1.5 seconds.)
The auxiliary output controls __________________________.
➜

9
© 2005 directed electronics—all rights reserved
Button
The remote start feature is turned On/Off by pressing this button twice.
and Buttons
The remote start timer mode function of the system is controlled
by pressing these buttons simultaneously.
and Buttons
The Turbo/Short Run feature is controlled by these buttons (refer
to the Turbo/Short Run section for additional details).
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
Button
Press and hold this button for 3-seconds to enter Panic Mode.
and and Buttons
When simultaneously pressed these buttons control the rear
window defogger during remote starting.

10 © 2005 directed electronics—all rights reserved
and Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls __________________________.
rreemmootteeooppeerraattiioonn
The remote start system operates at 434 MHz and incorporates
Directed’s proprietary XHF2 out-board technology transceiver. The
high frequency combined with Binary Data communication achieves
superior range with two-way communication.
system signal paging features
A page is the signal the control module sends to the remote control
as confirmation of receipt of a command or alarm system status.
When the remote control receives a page it will generate a page noti-
fication to the user (notifications are audible beeps) and the LED
Icons will display the current system status.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
➜

11
© 2005 directed electronics—all rights reserved
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will
be sent to the 2-way remote control. After receipt of an Alarm
Page at the 2-way remote, the LED icons will flash and the 2- way
remote will beep the alarm system status information.
An Alarm Page alert will repeat every 100 seconds to alert the
user that the alarm system was triggered and will continue until
the alarm page is cleared. A full sensor trigger will cause the 10
rapid beep sequence Alarm Page alert and a door opening and
any other trigger will cause the 4 rapid beep sequence Alarm
Page alert.
Page Recognition (Acknowledgement)
The 2-way remote will flash an icon and beep when it has
received a triggered response and will wait for you to recognize
the violation. Briefly press the button on the 2-way remote
while the 2-way remote is beeping to clear the alarm page. If the
alarm page was not cleared the 2-way remote will notify again at
another 100 seconds.
important! The Alarm Page alert can only be cleared dur-
ing notification, the lock button must be pressed while
the 2-way remote is beeping. The 2-way remote cansend
commands between the Alarm Page alerts (100 seconds)

12 © 2005 directed electronics—all rights reserved
Out of Range Notification
If a command is issued from the remote, but the remote is
beyond the range of the vehicle to receive the command, the
remote responds with 2 sets of 3 quick beeps and the Green LED
will flash 6-times.
pprrooggrraammmmiinnggrreemmoottee
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming mode is now entered.
Beeps On/Off
Press to select beeps On/Off. One beep is notification beeps
On, Two beeps is notification beeps Off. The notification beeps
are programmed On from the factory and can be programmed
Off if they are not desired. When programmed Off the remote
will only flash the LEDs as notification of a command page or
an alarm page.
Remote battery low notification
Press to select low battery notification On/Off. One beep is
low battery notification On. Two beeps is low battery notifica-
tion Off. The Low battery Beeps are programmed On from the
factory and can be programmed Off if they are not desired.
When programmed Off the remote will not give any notification
that the battery charge level in the remote is low.
➜

13
© 2005 directed electronics—all rights reserved
Page notification
The remote control can be programmed to notify the user of a
page (audibly beeping if the vehicle’s status changes, e.g. door
unlocked, engine started, vehicle violation, etc.). Press to
select page On/Off. One beep is page On, Two beeps is page Off.
When programmed off the remote will not give any notification
that a page was received from the vehicle.
To exit programming mode
The remote control will exit programming mode after 2-seconds
of inactivity and will emit 2 long beeps.
uussiinnggyyoouurrssyysstteemm
warning! safety first
The following safety warnings must be observed at all times:
➤Due to the complexity of this system, installation of this
product must only be performed by an authorized Directed
dealer.
➤When properly installed, this system can start the vehicle via
a command signal from the 2-way remote control. Therefore,
never operate the system in an enclosed area or partially
enclosed area without ventilation (such as a garage). When
parking in an enclosed or partially enclosed area or when
having the vehicle serviced, the remote start system must be
disabled using the installed toggle switch. It is the user's sole
responsibility to properly handle and keep out of reach from
children all 2-way remotes to assure that the system does not
unintentionally remote start the vehicle. TTHHEEUUSSEERRMMUUSSTT
➜

14 © 2005 directed electronics—all rights reserved
IINNSSTTAALLLLAACCAARRBBOONNMMOONNOOXXIIDDEEDDEETTEECCTTOORRIINN
OORRAABBOOUUTTTTHHEELLIIVVIINNGGAARREEAAAADDJJAACCEENNTTTTOOTTHHEE
VVEEHHIICCLLEE..AALLLLDDOOOORRSSLLE
EAADDIINNGGFFRROOMMAADDJJAACCEENNTT
LLIIVVIINNGGAARREEAASSTTOOTTHHEEEENNCCLLOOSSEEDDOORRPPAARRTTIIAALLLLYY
EENNCCLLOOSSEEDDVVEEHHIICCLLEESSTTOORRAAGGEEAARREEAAMMUUSSTTAATT
A
ALLLLTTIIMMEESSRREEMMAAIINNCCLLOOSSEEDD..These precautions are the
sole responsibility of the user.
➤Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. (1) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral
safety feature of the vehicle periodically checked, wherein the
vehicle must not remotely start while the car is in gear. This
testing should be performed by an authorized Directed dealer
in accordance with the Safety Check outlined in the product
installation guide. If the vehicle starts in gear, cease remote
start operation immediately and consult with the authorized
Directed dealer to fix the problem.
➤After the remote start module has been installed, contact
your authorized dealer to have him or her test the remote
start module by performing the Safety Check outlined in the
product installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The remote
start module must be removed or the installer must properly
reinstall the remote start system so that the vehicle does not
start in gear. All installations must be performed by an autho-
rized Directed dealer. OOPPEERRAATTIIOONNOOFFTTHHEERREEMMOOTTEE
SSTTAARRTTMMOODDUULLEEIIFFTTHHEEVVEEHHIICCLLEESSTTAARRTTSSIINNGGEEAARR
IISSCCOONNTTRRAARRYYTTOOIITTSSIINNTTEENNDDEEDDMMOODDE
EOOFFOOPPEERR--
AATTIIOONN..OOPPEERRAATTIINNGGTTHHEERREEMMOOTTEESSTTAARRTTSSYYSSTTEEMM
UUNNDDEERRTTHHEESSEECCOONNDDIITTIIOONNSSMMAAYYRREESSUULLTTIINN
PPRROOPPEERRTTYYDDAAM
MAAGGEEOORRPPEERRSSOONNAALLIINNJJUURRYY..YYOOUU

15
© 2005 directed electronics—all rights reserved
MMUUSSTTIIMMMMEEDDIIAATTEELLYYCCEEAASSEETTHHEEUUSSEEOOFFTTHHEE
UUNNIITTAANNDDSSEEEEKKTTHHEEAASSSSIISSTTAANNCCEEOOFFAANNAAUUTTHHOO--
RRIIZZEEDDDDIIRREECCTTEEDDDDEEAALLEER
RTTOORREEPPAAIIRROORR
DDIISSCCOONNNNEECCTTTTHHEEIINNSSTTAALLLLEEDDRREEMMOOTTEESSTTAARRTT
MMOODDUULLEE..DDIIRREECCTTEEDDWWIILLLLNNOOTTBBEEHHEELLDD
RREESSPPOONNSSIIBBLLEEOOR
RPPAAYYFFOORRIINNSSTTAALLLLAATTIIOONNOORR
RREEIINNSSTTAALLLLAATTIIOONNCCOOSSTTSS..
active arming
You can arm the system by pressing of your 2-way remote
for one second. When the system arms, from the vehicle you will
hear a short siren sound, or chirp, and see the parking lights flash
once. If the power door locks are controlled by the system, the
doors will also lock. While the system is armed, the in-vehicle
status LED will flash approximately once per second, indicating
that the system is actively protecting your vehicle. If you hear a
second chirp after arming and note that the in-vehicle’s status
LED is flashing in groups, see the Diagnostics Section of this
guide. This extra chirp is called Bypass Notification.
The remote responds to active arming with one beep and the
Orange LED will flash 3-times to indicate successful arming of
the system.
If after 2-seconds the remote beeps once and the Orange and
Red LEDs flash 3-times, the system has detected an active sensor
that should be checked.
If after 2-seconds the remote beeps once, the Orange LED flashes
6-times and the Red LED lights for 3-seconds, the system has
detected an open door, hood or trunk and has been bypassed.
➜

16 © 2005 directed electronics—all rights reserved
passive arming
The system can be programmed to arm itself automatically (called
passive arming). If the system is programmed for passive arming, it
will automatically arm 30 seconds after the ignition is turned off
and the system detects that you have left the vehicle by opening and
closing a door. Whenever the system is in its 30-second passive
arming countdown, the in-vehicle status LED will flash twice as
fast as it does when the system is armed. At the 20-second point of
the countdown, the siren will chirp to indicate that the system is
about to arm. At the 30-second point, the parking lights will flash
to indicate that the system is armed.
The remote responds to passive arming with one beep and the
Orange LED will flash 3-times to indicate successful arming of
the system.
When armed your vehicle is protected as follows:
➤Light impacts trigger the Warn Away®signal. When triggered,
the siren chirps and the parking lights flash for a few seconds.
➤Heavy impacts trip a Triggered Sequence. The sequence
consists of the siren sounding continuously and the parking
lights flashing for a pre-programmed period, which can range
in duration from 1 to 180 seconds.
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system will
not passively arm (unless forced passive arming is pro-
grammed on. See Programming Options section.) Addi-
tionally, each time a sensor is triggered during the arming
countdown, the 30-second countdown starts over.
➜

17
© 2005 directed electronics—all rights reserved
➤If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren output changes to a continuous blast.
This progressive response gives you time to disarm the system
with your 2-way remote if you inadvertently open the door
while the system is armed, while still providing instant re-
sponse (even if the door is immediately closed).
➤Turning on the ignition key will trip the same progressive re-
sponse as opening a door.
➤The optional starter kill prevents the vehicle’s starter from cranking.
➤Any full trigger of the alarm system will immediately send an
alarm page to your remote informing you that your vehicle
should be checked.
multi-level security arming
Multi-Level Security Arming allows you to select which of the
system's inputs or sensors will be active and which will be
bypassed when the system is armed. (See
Table of Zones section
of this guide.) Pressing (only in Standard Configuration)
again within five seconds of arming the system will activate the
Multi-Level Security feature. Each time is pressed again, a
different security level is selected. The different security levels are
selected as follows:
➤Press once: The siren chirps once. The system is armed.
➤Press a second time within five seconds: The siren chirps
twice followed by a long chirp. Zone 2 is now bypassed.
➤Press a third time within five seconds: The siren chirps
three times followed by a long chirp. Zone 4 is now bypassed.
➜